• 全部
  • 经验案例
  • 典型配置
  • 技术公告
  • FAQ
  • 漏洞说明
  • 全部
  • 全部
  • 大数据引擎
  • 知了引擎
产品线
搜索
取消
案例类型
发布者
是否解决
是否官方
时间
搜索引擎
匹配模式
高级搜索

3PAR 重新部署一个DL120 SP

2020-03-28 发表
  • 0关注
  • 0收藏 3510浏览
粉丝:22人 关注:0人

组网及说明

3PAR with DL120 SP

问题描述

3PAR DL120 没有物理串口,只能通过虚拟串口来进行配置,下面是详细步骤。

过程分析

The DL120 does not have a physical serial port. Instead it has a virtual serial port. When you attempt to rebuild the SP at some point the display switches to the virtual serial port and stops outputting on the graphic head.  The rebuild is still progressing and eventually will complete and give you a SP00000 Login> prompt on the graphics terminal.


To monitor the rebuild use the following process.

 

1.       Insert the DVD with the SP Software in the SPs drive.

2.       Configure the ip address on your laptop to be 10.255.155.49 / 255.255.255.248.

3.       Connect network cable from laptop to the service port on the back of the DL120 (right hand port)

                 

 

4.       Browse to the IP of the ILO, 10.255.155.52.  Login using Administrator and the password from the toe tag.

5.       Started an ssh session to the same IP address as the ILO. You need the Administrator password from the toe tag. 

6.       At the Hpilo> prompt type vsp to connect to the virtual serial port.

7.       From the ILO reset the SP and you will start to see output on both the ILO and the VSP (Virtual Serial Port).

8.       As the SP starts to boot select  F9 to enter Bios/Platform Configuration.

9.       Ensure that Virtual Install Disk and Internal SD Card Slot are [Disabled].

                

 

 

10.    After the setting are changed hit ESC to allow the SP to continue booting.

Execute all the following commands on the serial port

 

11.    At the following Menu Press 'ESC+!' for One-Time Boot Menu

 

Redundant ROM Detected - This system contains a valid backup system ROM

HP SmartMemory authenticated in all populated DIMM slots.

For access via BIOS Serial Console:

 

Press 'ESC+9' for System Utilities

Press 'ESC+0' for Intelligent Provisioning

Press 'ESC+!' for One-Time Boot Menu

Press 'ESC+@' for Network Boot

 

12.    In the One-Time Boot Menu hit <ENTER>

                One-Time Boot Menu                                                                                                                                                                                                                                                         > Legacy BIOS One-Time Boot Menu     

 

13.    Select <ENTER> a second time.

 /-----------------------------------------------------\                                                                                                                                         

|Select ENTER to enter the Legacy BIOS One-Time  Boot    |            

|Menu or ESC to cancel.                                                         |                                              

 |Enter (Exit) | ESC (Cancel)                                                   |

  \-----------------------------------------------------/

 

Booting in Legacy BIOS mode...

 

14.    Select the Boot option

 Please Choose one of the Following Default Boot Override Options:

      1) One Time Boot to CD-ROM

      2) One Time Boot to USB DriveKey

      3) One Time Boot to HDD

      4) One Time Boot to Network (1st NIC in IPL)

      5) One Time Boot to UEFI Boot Menu (after system reset)

      7) One Time Boot to Intelligent Provisioning (after system reset)

      8) Enter the System Utilities menu (after system reset)

      0) Exit Boot Override Menu and Continue Default Boot Process

 

15.    Select the Baud Rate which selects the proper SP hardware type.

16.    The Graphic port will stop outputting after and the Write protecting the kernel read-only data: 1980k

17.    The serial port will continue to show output as the SP rebuilds.

18.    After the Graphics terminal stopped outputting it took about 18 minutes to complete.

19.    The graphics head will start outputting a few minutes before it completes

20.    When it completes both terminals will show the login prompt   SP00000 Login>


解决方法

该案例对您是否有帮助:

您的评价:1

若您有关于案例的建议,请反馈:

0 个评论

该案例暂时没有网友评论

编辑评论

举报

×

侵犯我的权益 >
对根叔知了社区有害的内容 >
辱骂、歧视、挑衅等(不友善)

侵犯我的权益

×

泄露了我的隐私 >
侵犯了我企业的权益 >
抄袭了我的内容 >
诽谤我 >
辱骂、歧视、挑衅等(不友善)
骚扰我

泄露了我的隐私

×

您好,当您发现根叔知了上有泄漏您隐私的内容时,您可以向根叔知了进行举报。 请您把以下内容通过邮件发送到zhiliao@h3c.com 邮箱,我们会尽快处理。
  • 1. 您认为哪些内容泄露了您的隐私?(请在邮件中列出您举报的内容、链接地址,并给出简短的说明)
  • 2. 您是谁?(身份证明材料,可以是身份证或护照等证件)

侵犯了我企业的权益

×

您好,当您发现根叔知了上有关于您企业的造谣与诽谤、商业侵权等内容时,您可以向根叔知了进行举报。 请您把以下内容通过邮件发送到 zhiliao@h3c.com 邮箱,我们会在审核后尽快给您答复。
  • 1. 您举报的内容是什么?(请在邮件中列出您举报的内容和链接地址)
  • 2. 您是谁?(身份证明材料,可以是身份证或护照等证件)
  • 3. 是哪家企业?(营业执照,单位登记证明等证件)
  • 4. 您与该企业的关系是?(您是企业法人或被授权人,需提供企业委托授权书)
我们认为知名企业应该坦然接受公众讨论,对于答案中不准确的部分,我们欢迎您以正式或非正式身份在根叔知了上进行澄清。

抄袭了我的内容

×

原文链接或出处

诽谤我

×

您好,当您发现根叔知了上有诽谤您的内容时,您可以向根叔知了进行举报。 请您把以下内容通过邮件发送到zhiliao@h3c.com 邮箱,我们会尽快处理。
  • 1. 您举报的内容以及侵犯了您什么权益?(请在邮件中列出您举报的内容、链接地址,并给出简短的说明)
  • 2. 您是谁?(身份证明材料,可以是身份证或护照等证件)
我们认为知名企业应该坦然接受公众讨论,对于答案中不准确的部分,我们欢迎您以正式或非正式身份在根叔知了上进行澄清。

对根叔知了社区有害的内容

×

垃圾广告信息
色情、暴力、血腥等违反法律法规的内容
政治敏感
不规范转载 >
辱骂、歧视、挑衅等(不友善)
骚扰我
诱导投票

不规范转载

×

举报说明

提出建议

    +

亲~登录后才可以操作哦!

确定

亲~检测到您登陆的账号未在http://hclhub.h3c.com进行注册

注册后可访问此模块

跳转hclhub

你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作