• 全部
  • 经验案例
  • 典型配置
  • 技术公告
  • FAQ
  • 全部
  • 全部
产品线
搜索
取消
案例类型
发布者
是否解决
是否官方
时间
高级搜索

POE troubleshooting method

2021-02-04 Published
  • 0关注
  • -1收藏,204浏览
粉丝:0人 关注:0人

Network Topology

NULL

Configuration Steps

The idea of locating the fault is: first check whether the powered PD device meets the POE power supply requirements of our device, then check the power supply status of the device's POE interface, and finally collect and check related information analysis according to the error message when the POE function is enabled.

1.Check network cable distance

It is recommended that the power supply device and the power receiving PD device use a twisted pair cable with specifications exceeding Category 5 and above, and the distance is less than 100 meters.

2.Enable non-standard PD detection function

Only after the non-standard PD function can be detected on our equipment, the equipment can detect the non-standard PD and supply power to it.

Command:poe legacy enable pse pse-id

3.Check the working status of the PoE interface of a device failure

Command:display poe interface gigabitethernet

<H3C> display poe interface gigabitethernet 1/0/1

 Port Power Enabled               : enabled

 Port Power Priority              : high

 Port Operating Status            : on

 Port IEEE Class                   : 0

 Port Detection Status            : delivering-power

 Port Power Mode                   : signal


Port Operating Status

l off: The power supply function is disabled

l on: power is being supplied normally

l power-lack: The remaining guaranteed power of the PSE is insufficient, resulting in the inability to supply power to the PoE interface with priority Critical

l power-deny: refuse to supply power, the PD requires more power than the configured power

l power-itself: The external device is powering itself

l power-limit: The power is being restricted, and the PD requires more power than the configured power, and the PSE still supplies power according to the configured power

 

Port Detection Status

l disabled: PoE interface power supply is prohibited

l searching: searching PD

l Delivering-power: Power is being supplied to PD

l fault: error

l test: test status

l other-fault: other error status

l pd-disconnect: PD is not connected


4.Check whether an error is prompted when poe enable is enabled on the interface

[H3C]int Ethernet 1/0/1

[H3C-Ethernet1/0/1]poe enable

PoE is not supported on the port!

5.Use FULL mode to upgrade device PSE file

If an error is displayed when the POE function is enabled on the interface, use the FULL mode to upgrade the PSE processing software. 

Command: poe update full filename pse pse-id

For example: Upgrade S5120-EI switch PSE processing software

[H3C] poe update full 00061204_0384_001_h3c.bin pse 4

This command will refresh firmware on the specific PSE(s), Continue? [Y/N]:y

 System is downloading firmware into the hardware. Please wait ..

 Update success

Note: Please contact H3CTS after-sales service for the PSE processing software required for the upgrade.

6. If the interface does not prompt an error when the POE function is enabled,Collect and feedback equipment related POE fault information.  Please collect the following information and feed it back to the after-sales engineer.

(1) Collect POE status information on the device at the time of failure.

<H3C>dis power

<H3C>dis poe device

<H3C>dis poe pse

<H3C> dis poe interface and dis poe int gx/x/x (collect both faulty and normal ports)

<H3C>dis poe interface power

<H3C>sys

[H3C] en_diag

[H3C-diagnose] debug poe dimm-status unit_id (the default unit_id of non-IRF devices is 1)

[H3C-diagnose] debug poe port-power unit_id

[H3C-diagnose] debug poe pse-info unit_id

[H3C-diagnose] debug poe sys-status unit_id

 

(2) Collect the diagnostic information of the equipment at the time of failure.

<H3C>dis diag


Key Configuration

If an error is displayed when the POE function is enabled on the interface, use the FULL mode to upgrade the PSE processing software. 

Command: poe update full filename pse pse-id

If the interface does not prompt an error when the POE function is enabled,Collect and feedback equipment related POE fault information.

0 comments

No comments

Add Comments:

举报

×

侵犯我的权益 >
对根叔知了社区有害的内容 >
辱骂、歧视、挑衅等(不友善)

侵犯我的权益

×

泄露了我的隐私 >
侵犯了我企业的权益 >
抄袭了我的内容 >
诽谤我 >
辱骂、歧视、挑衅等(不友善)
骚扰我

泄露了我的隐私

×

您好,当您发现根叔知了上有泄漏您隐私的内容时,您可以向根叔知了进行举报。 请您把以下内容通过邮件发送到zhiliao@h3c.com 邮箱,我们会尽快处理。
  • 1. 您认为哪些内容泄露了您的隐私?(请在邮件中列出您举报的内容、链接地址,并给出简短的说明)
  • 2. 您是谁?(身份证明材料,可以是身份证或护照等证件)

侵犯了我企业的权益

×

您好,当您发现根叔知了上有关于您企业的造谣与诽谤、商业侵权等内容时,您可以向根叔知了进行举报。 请您把以下内容通过邮件发送到 zhiliao@h3c.com 邮箱,我们会在审核后尽快给您答复。
  • 1. 您举报的内容是什么?(请在邮件中列出您举报的内容和链接地址)
  • 2. 您是谁?(身份证明材料,可以是身份证或护照等证件)
  • 3. 是哪家企业?(营业执照,单位登记证明等证件)
  • 4. 您与该企业的关系是?(您是企业法人或被授权人,需提供企业委托授权书)
我们认为知名企业应该坦然接受公众讨论,对于答案中不准确的部分,我们欢迎您以正式或非正式身份在根叔知了上进行澄清。

抄袭了我的内容

×

原文链接或出处

诽谤我

×

您好,当您发现根叔知了上有诽谤您的内容时,您可以向根叔知了进行举报。 请您把以下内容通过邮件发送到zhiliao@h3c.com 邮箱,我们会尽快处理。
  • 1. 您举报的内容以及侵犯了您什么权益?(请在邮件中列出您举报的内容、链接地址,并给出简短的说明)
  • 2. 您是谁?(身份证明材料,可以是身份证或护照等证件)
我们认为知名企业应该坦然接受公众讨论,对于答案中不准确的部分,我们欢迎您以正式或非正式身份在根叔知了上进行澄清。

对根叔知了社区有害的内容

×

垃圾广告信息
色情、暴力、血腥等违反法律法规的内容
政治敏感
不规范转载 >
辱骂、歧视、挑衅等(不友善)
骚扰我
诱导投票

不规范转载

×

举报说明

提出建议

    +

亲~登录后才可以操作哦!

确定

你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作