设备:6520X-EI
版本:R6510
设备万兆口1/0/41口下连服务器,端口有震荡日志:
%Oct 21 17:50:16:506 2021 yewuSW-1 IFNET/3/PHY_UPDOWN: Physical state on the interface Ten-GigabitEthernet1/0/41 changed to up.
%Oct 21 17:50:16:511 2021 yewuSW-1 IFNET/5/LINK_UPDOWN: Line protocol state on the interface Ten-GigabitEthernet1/0/41 changed to up.
%Oct 21 17:50:18:202 2021 yewuSW-1 LLDP/6/LLDP_CREATE_NEIGHBOR: Nearest bridge agent neighbor created on port Ten-GigabitEthernet1/0/41 (IfIndex 41), neighbor's chassis ID is f8f2-1eb4-48b1, port ID is f8f2-1eb4-48b1.
%Oct 21 17:50:31:155 2021 yewuSW-1 IFNET/3/PHY_UPDOWN: Physical state on the interface Ten-GigabitEthernet1/0/41 changed to down.
但是设备上并无相应TC报文产生,查看端口stp是使能的,且没有配置边缘端口:
#
interface Ten-GigabitEthernet1/0/41
port link-mode bridge
description pT-OFF-N-41
port link-type trunk
undo port trunk permit vlan 1
port trunk permit vlan 1000 to 1254 2000 to 2069
#
后查看端口stp状态发现,边缘端口有两种状态,一种是config即用户配置的,另一种是active,即设备自动检测的,设备自动将端口设为了边缘端口,因此在端口震荡时不会产生TC报文。
----[Port41(Ten-GigabitEthernet1/0/41)][FORWARDING]----
Port protocol : Enabled
Port role : Designated Port
Port ID : 128.41
Port cost(Legacy) : COnfig=auto, Active=2
Desg.bridge/port : 32768.00be-d5ed-49c0, 128.41
Port edged : COnfig=disabled, Active=enable//自动变成边缘端口
Point-to-Point : COnfig=auto, Active=true
Transmit limit : 10 packets/hello-time
TC-Restriction : Disabled
Role-Restriction : Disabled
Protection type : COnfig=none, Active=none
MST BPDU format : COnfig=auto, Active=802.1s
Port Config-
Digest-Snooping : Disabled
Rapid transition : True
Num of VLANs mapped : 325
Port times : Hello 2s MaxAge 20s FwdDelay 15s MsgAge 1s RemHops 20
BPDU sent : 1767753
TCN: 0, Config: 0, RST: 0, MST: 1767753
BPDU received : 0
TCN: 0, Config: 0, RST: 0, MST: 0
当端口开启生成树功能后,设备将自动对端口进行一次边缘端口监测。即如果端口在(2×Hello Time+1)秒内没有收到BPDU报文,则会自动将端口设置为边缘端口。
该案例暂时没有网友评论
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作