组网及说明
1. 适用产品系列
本手册适用于如下产品：本案例适用于如WX3008、WX3010、WX3010E、WX3024E、WX5002 WX5004等WX30、WX50系列的AC。
LAN口默认管理地址为192.168.0.100。
配置步骤
1. 不需要之前的配置文件，恢复出厂设置
以下标黑部分为设备自动打印部分，标红加粗的命令是需要手动输入。
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing.......................Done!
BootWare Validating...
Press Ctrl+B to enter extended boot menu... //如果看到该提示及时按Ctrl+B进入botroom菜单
BotWare password: Not required. Please press Enter to Continue.
Password recovery capability is enabled. //如果看到此提示，则表示设备开启了密码恢复功能。
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 6 //选择6 跳过配置文件
Flag Set Success.
===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 0 //选择0重启设备
System is starting...
Press ENTER to get started.
跳过启动文件后直接保存当前配置，再重启
The current Configuration will be written to the device. Are you sure? [Y/N]:y
Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):（输入回车）
flash:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait...
Configuration is saved to device successfully.
Start to check Configuration with next startup Configuration file, please wait.........DONE!
Current Configuration may be lost after the reboot, save current Configuration? [Y/N]:y
This command will reboot the device. Continue? [Y/N]:y
重启完成后使用默认配置启动，恢复出厂成功
2. 保留原有配置，只修改密码
2.1 以忽略系统当前配置的方式启动
以下标黑部分为设备自动打印部分，标红加粗的命令是需要手动输入。
详细配置过程：
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing.......................Done!
BootWare Validating...
Press Ctrl+B to enter extended boot menu...//按Ctrl+B进入botroom菜单
BotWare password: Not required. Please press Enter to Continue.
Password recovery capability is enabled. //如果看到此提示，则表示设备开启了密码恢复功能。
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 6 //选择6 跳过配置文件
Flag Set Success.
===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 0 //选择0重启设备
System is starting...
Press ENTER to get started.
Directory of flash:/
2 -rw- 1666 Apr 26 2000 12:05:39 startup.cfg
29106 KB total (16876 KB free)
给设备和电脑配置成同网段Ip地址，举例：WAC配置成192.168.100.1/24，电脑配置成192.168.100.2/24），在电脑上使用3CDaemon软件搭建TFTP服务器，打开3CDaemon服务器，目录指向电脑E盘，然后点击应用。
[H3C]interface Vlan-interface 1
[H3C-Vlan-interface1]ip address 192.168.100.1 24
[H3C-Vlan-interface1]quit
[H3C]ping 192.168.100.2
PING 192.168.100.2: 56 data bytes, press CTRL_C to break
Reply from 192.168.100.2: bytes=56 Sequence=1 ttl=128 time=7 ms
//提示设备到电脑网络可达
//从设备上下载startup.cfg文件到电脑E盘
File will be transferred in binary mode
Sending file to remote TFTP server. Please wait... |
TFTP: 1666 bytes sent in 0 seCond(s).
File uploaded successfully.
下载成功：
可以到本地相关路径（此例子中是E盘）查看到相关文件。
解决方法：
使用记事本打开startup.cfg文件
删除aux0口下的认证方式和密码并保存文件
覆盖当前配置文件
The file startup.cfg exists. Overwrite it? [Y/N]:y
Verifying server file...
Deleting the old file, please wait...
...
File will be transferred in binary mode
Downloading file from remote TFTP server, please wait....
TFTP: 1166 bytes received in 0 seCond(s)
File downloaded successfully.
Start to check Configuration with next startup Configuration file, please wait.........DONE!
Current Configuration may be lost after the reboot, save current Configuration? [Y/N]:n 不保存配置
This command will reboot the device. Continue? [Y/N]:y 确定继续重启
3. 适用产品系列
本手册适用于如下产品：MSG360-4、MSG360-10、MSG360-10P、MSG360-20、MSG360-20N、MSG360-40、WAC380-30、WAC380-60、WAC380-90、WAC380-120、WAC381
4. 保留原有配置，只修改密码
从设备中下载startup.cfg到电脑，具体参考：1.2保留原有配置，只修改密码
解决方法：
使用记事本打开startup.cfg文件
删除Con0口下的认证方式和密码并保存文件
覆盖当前配置文件
The file startup.cfg exists. Overwrite it? [Y/N]:y
Verifying server file...
Deleting the old file, please wait...
...
File will be transferred in binary mode
Downloading file from remote TFTP server, please wait....
TFTP: 1166 bytes received in 0 seCond(s)
File downloaded successfully.
Start to check Configuration with next startup Configuration file, please wait.........DONE!
Current Configuration may be lost after the reboot, save current Configuration? [Y/N]:n 不保存配置
This command will reboot the device. Continue? [Y/N]:y 确定继续重启
配置关键点
该案例暂时没有网友评论
编辑评论
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证，请认证邮箱或绑定手机后进行当前操作