不涉及
不涉[CR16010F]mirroring-group 1 mirroring-port GE1/2/12 to g1/2/15 both
[CR16010F]mirroring-group 1 monitor-port g1/2/9
The type of the mirroring port in the mirroring group
如下操作记录显示,现场在部署本地端口镜像时,提示镜像源端口类型不支持。
[CR16010F]mirroring-group 1 monitor-port g1/2/9
The type of the mirroring port in the mirroring group is not supported.
查看具体镜像组配置信息如下:
< CR16010F>dis mirroring-group 1
Mirroring group 1:
Type: Local
Status: Incomplete
Mirroring port:
GigabitEthernet1/2/12.3036 Both
GigabitEthernet1/2/13.3026 Both
GigabitEthernet1/2/14.3016 Both
GigabitEthernet1/2/15.3006 Both
现场镜像源端口采用的子接口,而子接口是不支持做镜像来用的,告知现场修改。
后面现场修改的过程中,把镜像源端口设置为具体物理接口,同样提示源接口类型不支持,操作记录如下: [CR16010F]mirroring-group 1 mirroring-port GE1/2/12 to g1/2/15 both
[CR16010F]mirroring-group 1 monitor-port g1/2/9
The type of the mirroring port in the mirroring group is not supported.
然后,具体查看版本说明书和1号槽位单板信息,不存在相关限制;确认本地镜像资源数也没有超规格(每个芯片,对镜像源端口的方向 数量 存在限制,不能超过4个)。
后面远程现场设备操作发现,配置本地镜组源端口时,配置过程中一次指定一个源端口时,是可以正常下发配置的,无报错,如下显示:
[CR16010F]mirroring-group 1 mirroring-port GE1/2/12 both
[CR16010F]mirroring-group 1 monitor-port g1/2/9
而采用下面配置方式,即一次指定多个镜像源端口时,便会提示接口类型不支持的报错:
[CR16010F]mirroring-group 1 mirroring-port GE1/2/12 to g1/2/15 both
[CR16010F]mirroring-group 1 monitor-port g1/2/9
The type of the mirroring port in the mirroring group is not supported.
了解到现场情况,和产品线专家沟通确认得知:
上面这种配置方式,1/2/12到1/2/15,会把中间的子接口也包含进去,但是子接口一直都不支持镜像,所以返回接口类型不支持。如果中间配置了很多子接口,那就不能用1/2/12 to 1/2/15的方式配置,需要一个个接口进行配置。
本地镜像组中的源端口单独一个个定义配置即可。
该案例暂时没有网友评论
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作