组网及说明
1. 适用产品系列
本手册适用于如下产品：WAC360、WAC 361、MSG360-4、MSG360-10、MSG360-10P、MSG360-20、MSG360-20N、MSG360-40、WAC380-30、WAC380-60、WAC380-90、WAC380-120、WAC381
胖AP：WAP712C、WAP722E、WAP722S、WAP722、WAP621
配置步骤
1.1.1 不需要之前的配置文件，恢复出厂设置
以下标黑部分为设备自动打印部分，标红加粗的命令是需要手动输入。
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing.......................Done!
BootWare Validating...
Press Ctrl+B to enter extended boot menu... //如果看到该提示及时按Ctrl+B进入botroom菜单
BotWare password: Not required. Please press Enter to Continue.
Password recovery capability is enabled. //如果看到此提示，则表示设备开启了密码恢复功能。
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 6 //选择6 跳过配置文件
Flag Set Success.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 0 //选择0重启设备
System is starting...
Press ENTER to get started.
跳过启动文件后直接保存当前配置，再重启
<H3C>save
The current Configuration will be written to the device. Are you sure? [Y/N]:y
Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):（输入回车）
flash:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait...
Configuration is saved to device successfully.
<H3C>reboot
Start to check Configuration with next startup Configuration file, please wait.........DONE!
Current Configuration may be lost after the reboot, save current Configuration? [Y/N]:y
This command will reboot the device. Continue? [Y/N]:y
重启完成后使用默认配置启动，恢复出厂成功
1.2 保留原有配置，只修改密码
本手册适用于如下产品：WAC360、WAC 361、胖AP：WAP712C、WAP722E、WAP722S、WAP722、WAP621
1.2.1 以忽略系统当前配置的方式启动
以下标黑部分为设备自动打印部分，标红加粗的命令是需要手动输入。
详细配置过程：
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
The Extend BootWare is self-decompressing.......................Done!
BootWare Validating...
Press Ctrl+B to enter extended boot menu...//按Ctrl+B进入botroom菜单
BotWare password: Not required. Please press Enter to Continue.
Password recovery capability is enabled. //如果看到此提示，则表示设备开启了密码恢复功能。
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 6 //选择6 跳过配置文件
Flag Set Success.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Clear Super Password |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTEND-ASSISTANT MENU
Ctrl+F: Format File System
Enter your choice(0-9): 0 //选择0重启设备
System is starting...
Press ENTER to get started.
<H3C>dir //查看设备配置文件：startup.cfg
Directory of flash:/
2 -rw- 1666 Apr 26 2000 12:05:39 startup.cfg
29106 KB total (16876 KB free)
给设备和电脑配置成同网段Ip地址，举例：WAC配置成192.168.100.1/24，电脑配置成192.168.100.2/24），在电脑上使用3CDaemon软件搭建TFTP服务器，打开3CDaemon服务器，目录指向电脑E盘，然后点击应用。
<H3C>system
[H3C]interface Vlan-interface 1
[H3C-Vlan-interface1]ip address 192.168.100.1 24
[H3C-Vlan-interface1]quit
[H3C]ping 192.168.100.2
PING 192.168.100.2: 56 data bytes, press CTRL_C to break
Reply from 192.168.100.2: bytes=56 Sequence=1 ttl=128 time=7 ms
//提示设备到电脑网络可达
<H3C>tftp 192.168.100.2 put startup.cfg
//从设备上下载startup.cfg文件到电脑E盘
File will be transferred in binary mode
Sending file to remote TFTP server. Please wait... |
TFTP: 1666 bytes sent in 0 seCond(s).
File uploaded successfully.
下载成功：
可以到本地相关路径（此例子中是E盘）查看到相关文件。
解决方法：
使用记事本打开startup.cfg文件
删除aux0口下的认证方式和密码并保存文件
覆盖当前配置文件
<H3C>tftp 192.168.100.20 get startup.cfg
The file startup.cfg exists. Overwrite it? [Y/N]:y
Verifying server file...
Deleting the old file, please wait...
...
File will be transferred in binary mode
Downloading file from remote TFTP server, please wait....
TFTP: 1166 bytes received in 0 seCond(s)
File downloaded successfully.
<H3C>reboot
Start to check Configuration with next startup Configuration file, please wait.........DONE!
Current Configuration may be lost after the reboot, save current Configuration? [Y/N]:n 不保存配置
This command will reboot the device. Continue? [Y/N]:y 确定继续重启
1.3 适用产品系列
本手册适用于如下产品：MSG360-4、MSG360-10、MSG360-10P、MSG360-20、MSG360-20N、MSG360-40、WAC380-30、WAC380-60、WAC380-90、WAC380-120、WAC381
1.4 保留原有配置，只修改密码
从设备中下载startup.cfg到电脑，具体参考：1.2保留原有配置，只修改密码
解决方法：
使用记事本打开startup.cfg文件
删除Con0口下的认证方式和密码并保存文件
覆盖当前配置文件
<H3C>tftp 192.168.100.2 get startup.cfg
The file startup.cfg exists. Overwrite it? [Y/N]:y
Verifying server file...
Deleting the old file, please wait...
...
File will be transferred in binary mode
Downloading file from remote TFTP server, please wait....
TFTP: 1166 bytes received in 0 seCond(s)
File downloaded successfully.
<H3C>reboot
Start to check Configuration with next startup Configuration file, please wait.........DONE!
Current Configuration may be lost after the reboot, save current Configuration? [Y/N]:n 不保存配置
This command will reboot the device. Continue? [Y/N]:y 确定继续重启