1-2 51口-51口
2-3 52口-52口
3-4 51口-51口
4-1 52口-52口
1/2是 1/0/51
2/1是 2/0/51这样行不
类似这样子
(0)
看你是环形,还是链形。建议环形,参考:
由于网络规模迅速扩大,当前中心交换机(Device A)转发能力已经不能满足需求(如图1-22)。现在需要另增三台设备,将这四台设备组成一个IRF(如图1-23)。使网络易管理、易维护。
· 分别配置四台成员设备的成员编号、优先级、IRF端口;
· 将四台设备切换到IRF模式。
# 设置Device A的成员编号为1,成员优先级为12。
[Sysname] irf member 1
[Sysname] irf priority 12
# 创建IRF端口1,并将它与物理端口Ten-GigabitEthernet3/0/2绑定。
[Sysname-irf-port 1] port group interface ten-gigabitethernet 3/0/2
[Sysname-irf-port 1] quit
# 创建IRF端口2,并将它与物理端口Ten-GigabitEthernet3/0/1绑定。
[Sysname-irf-port 2] port group interface ten-gigabitethernet 3/0/1
[Sysname-irf-port 2] quit
# 将当前配置保存到下次启动配置文件。
# 将设备的运行模式切换到IRF模式。
[Sysname] chassis convert mode irf
The device will switch to IRF mode and reboot.
You are recommended to save the current running configuration and specify the configuration file for the next startup. Continue? [Y/N]:y
Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
flash:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait...
Saved the current configuration to mainboard device successfully.
Do you want to convert the content of the next startup configuration file flash:
/startup.cfg to make it available in stand-alone mode? [Y/N]:y
Now rebooting, please wait...
设备重启后Device A形成了只有一台成员设备的IRF。
# 配置Device B的成员编号为2,成员优先级为26。
[Sysname] irf member 2
[Sysname] irf priority 26
# 创建IRF端口1,并将它与物理端口Ten-GigabitEthernet3/0/1绑定。
[Sysname-irf-port 1] port group interface ten-gigabitethernet 3/0/1
[Sysname-irf-port 1] quit
# 创建IRF端口2,并将它与物理端口Ten-GigabitEthernet3/0/2绑定。
[Sysname-irf-port 2] port group interface ten-gigabitethernet 3/0/2
[Sysname-irf-port 2] quit
# 将当前配置保存到下次启动配置文件。
# 将设备的运行模式切换到IRF模式。
[Sysname] chassis convert mode irf
The device will switch to IRF mode and reboot.
You are recommended to save the current running configuration and specify the configuration file for the next startup. Continue? [Y/N]:y
Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
flash:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait...
Saved the current configuration to mainboard device successfully.
Do you want to convert the content of the next startup configuration file flash:
/startup.cfg to make it available in stand-alone mode? [Y/N]:y
Now rebooting, please wait...
设备B重启后与设备A形成IRF。
# 配置Device C的成员编号为3,成员优先级为6。
[Sysname] irf member 3
[Sysname] irf priority 6
# 创建IRF端口1,并将它与物理端口Ten-GigabitEthernet3/0/2绑定。
[Sysname-irf-port 1] port group interface ten-gigabitethernet 3/0/2
[Sysname-irf-port 1] quit
# 创建IRF端口2,并将它与物理端口Ten-GigabitEthernet3/0/1绑定。
[Sysname-irf-port 2] port group interface ten-gigabitethernet 3/0/1
[Sysname-irf-port 2] quit
# 将当前配置保存到下次启动配置文件。
# 将设备的运行模式切换到IRF模式。
[Sysname] chassis convert mode irf
The device will switch to IRF mode and reboot.
You are recommended to save the current running configuration and specify the configuration file for the next startup. Continue? [Y/N]:y
Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
flash:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait...
Saved the current configuration to mainboard device successfully.
Do you want to convert the content of the next startup configuration file flash:
/startup.cfg to make it available in stand-alone mode? [Y/N]:y
Now rebooting, please wait...
设备C重启后与设备A、设备B形成IRF。
# 配置Device B的成员编号为4,成员优先级为2。
[Sysname] irf member 4
[Sysname] irf priority 2
# 创建IRF端口1,并将它与物理端口Ten-GigabitEthernet3/0/1绑定。
[Sysname-irf-port 1] port group interface ten-gigabitethernet 3/0/1
[Sysname-irf-port 1] quit
# 创建IRF端口2,并将它与物理端口Ten-GigabitEthernet3/0/2绑定。
[Sysname-irf-port 2] port group interface ten-gigabitethernet 3/0/2
[Sysname-irf-port 2] quit
# 将当前配置保存到下次启动配置文件。
# 将设备的运行模式切换到IRF模式。
[Sysname] chassis convert mode irf
The device will switch to IRF mode and reboot.
You are recommended to save the current running configuration and specify the configuration file for the next startup. Continue? [Y/N]:y
Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
flash:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait...
Saved the current configuration to mainboard device successfully.
Do you want to convert the content of the next startup configuration file flash:
/startup.cfg to make it available in stand-alone mode? [Y/N]:y
Now rebooting, please wait...
设备D重启后与设备A、设备B和设备C形成IRF。
(0)
暂无评论
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明
暂无评论