两台交换机端口分别配置trunk,允许vlan通过,但华为端交换机端口UP,华三端交换机端口down。尝试过两侧强制速率,全双工模式,但最后华为端口up,华三端还是down。
华三端口配置:
interface GigabitEthernet1/0/50
description to_1-1-HXJF-S9312-JKHX201GE1/0/18
port link-type trunk
undo port trunk permit vlan 1
port trunk permit vlan 2 to 4094
speed 1000
duplex full
华三端口状态:
GigabitEthernet1/0/50
Current state: DOWN
Line protocol state: DOWN
IP packet frame type: Ethernet II, hardware address: 4077-a9ce-55d3
Description: to_1-1-HXJF-S9312-JKHX201GE1/0/18
Bandwidth: 1000000 kbps
Loopback is not set
Media type is stack wire, Port hardware type is STACK_SFP_PLUS
1000Mbps-speed mode, full-duplex mode
Link speed type is force link, link duplex type is force link
Flow-control is not enabled
Maximum frame length: 10240
Allow jumbo frames to pass
Broadcast max-ratio: 100%
Multicast max-ratio: 100%
Unicast max-ratio: 100%
PVID: 1
MDI type: Automdix
Port link-type: Trunk
VLAN Passing: 1000-1005, 4090
VLAN permitted: 2-4094
Trunk port encapsulation: IEEE 802.1q
Port priority: 0
Last link flapping: 0 hours 6 minutes 16 seconds
Last clearing of counters: Never
华为端口配置:
interface GigabitEthernet0/0/26
undo negotiation auto
description to_1-1-HXJF-S9312-JKHX201-G1/0/18
port link-type trunk
undo port trunk allow-pass vlan 1
port trunk allow-pass vlan 2 to 4094
华为端口状态:
GigabitEthernet0/0/26 current state : UP
Line protocol current state : UP
Description:to_1-1-HXJF-S9312-JKHX201-G1/0/18
Switch Port, PVID : 1, TPID : 8100(Hex), The Maximum Frame Length is 9216
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 3cc7-869f-2e8c
Last physical up time : 2021-11-23 13:53:17
Last physical down time : 2021-11-23 13:50:59
Current system time: 2021-11-23 13:56:09
Port Mode: COMMON FIBER, Transceiver: 1X_CopperPassive_SFP
Speed : 1000, Loopback: NONE
Duplex: FULL, Negotiation: DISABLE
Mdi : -, Flow-control: DISABLE
Last 300 seconds input rate 0 bits/sec, 0 packets/sec
Last 300 seconds output rate 65320 bits/sec, 62 packets/sec
Input peak rate 59835832 bits/sec, Record time: 2021-11-21 20:46:07
Output peak rate 1839048 bits/sec, Record time: 2021-11-21 20:53:55
(0)
功率有没有问题,换一下模块试试
两端的接口清一下配置试试
(0)
都恢复缺省配置后先配置强制速率和全双工模式,然后再配置trunk吗?
接口恢复配置。不需要强制,先默认看看能不能起来,起不来再强制,最后配置接口属性
找出原因了,是华三交换机不支持级联线导致的,更换为光模块就互通了。
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明