H3C 和锐捷二层动态聚合后 链路负载模式需要怎么调整?
h3c:聚合模式
interface Bridge-Aggregation15
description newcore
port link-type trunk
undo port trunk permit vlan 1
port trunk permit vlan 2 to 4094
link-aggregation mode dynamic
查看聚合负载模式:
—————————————————————————————————————————————————————————————————
锐捷聚合模式
LAN_CORE#show interfaces aggregatePort 1
Index(dec):330 (hex):14a
AggregatePort 1 is UP , line protocol is UP
Hardware is AggregateLink AggregatePort, address is 1082.3de9.fc5c (bia 1082.3de9.fc5c)
Interface address is: no ip address
Interface IPv6 address is:
No IPv6 address
MTU 1500 bytes, BW 20000000 Kbit
Encapsulation protocol is Ethernet-II, loopback not set
Keepalive interval is 10 sec , set
Carrier delay is 2 sec
Priority is 0
Medium-type is Fiber
Admin duplex mode is AUTO, oper duplex is Full
Admin speed is AUTO, oper speed is 10G
Flow control admin status is OFF, flow control oper status is OFF
Admin negotiation mode is OFF, oper negotiation state is OFF
Storm Control: Broadcast is OFF, Multicast is OFF, Unicast is OFF
Bridge attributes:
Port-type: trunk
Native vlan: 1
Allowed vlan lists: 1-4094
Active vlan lists: 1-200,202,301-302
Aggregate Port Informations:
Aggregate Number: 1
Name: "AggregatePort 1"
Members: (count=2)
Lower Limit: 1
TenGigabitEthernet 1/4/25 Link Status: Up Lacp Status: bndl
TenGigabitEthernet 2/4/25 Link Status: Up Lacp Status: bndl
Load Balance by: Enhanced Profile
Rxload is 1/255, Txload is 1/255
Input peak rate: 790328 bits/sec, at 2024-05-10 18:12:36
Output peak rate: 1708691774 bits/sec, at 2024-05-24 21:28:24
10 seconds input rate 83 bits/sec, 0 packets/sec
10 seconds output rate 207148 bits/sec, 274 packets/sec
419005 packets input, 65307498 bytes, 0 no buffer, 0 dropped
Received 4043 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 abort
981689082 packets output, 99910638880 bytes, 0 underruns, 0 no buffer, 0 dropped
0 output errors, 0 collisions, 0 interface resets
(0)
最佳答案
保持默认有什么问题么
(0)
现在可以聚合起来。需不需要两遍统一一下?有没有问题不知道
默认不需要的
锐捷默认的负载就是 源mac 目的mac 吧 !华三的默认也是,你不用改,要改的话两端改成一致的
(1)
这个是用那个命令查看的
display link-aggregation load-sharing mode Link-aggregation load-sharing mode: Layer 2 traffic: packet type-based sharing Layer 3 traffic: packet type-based sharing
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明
默认不需要的