请问该交换机出现该日志的原因是什么?
日志如下:IFMON/4/IFMON_PKT_DROP_RATE_RISING:The packet drop rate on slot 1 exceeds the upper threshold. Threshold=1000, value=1665, interval=10s, protocol=30.
该交换机作为接入交换机
(0)
最佳答案
该日志表示 Slot 1 的丢包率在 10 秒内达到 1665 pps(每秒丢包数),超出预设阈值(1000 pps),触发告警。
protocol=30
对应特定协议(需结合 MIB 库确认具体协议类型,如 IPv4/IPv6 或其他应用层协议)。流量突发过载
display interface
查看 Slot 1 关联端口的实时流量(Input/Output rate
)及丢包统计(Drops
字段)。硬件故障或配置异常
display transceiver diagnosis
)及硬件告警(display alarm
)。监控阈值设置不合理
display interface-monitor
确认当前阈值配置。协议处理异常
30
对应的协议处理存在 Bug 或资源泄露。protocol=30
的具体协议类型及已知问题。
display interface Ten-GigabitEthernet1/X/X # 替换为实际接口
Input/Output rate
持续接近端口带宽,需优化流量调度或扩容13。display transceiver diagnosis interface Ten-GigabitEthernet1/X/X
Rx Power
)是否在正常范围(-3~-14 dBm)。shutdown
undo shutdown
interface-monitor packet-drop threshold upper 2000 # 建议阈值上调至 2000 pps
undo interface-monitor packet-drop enable
(不推荐)24。display version
30
的详细解释及修复方案。qos car
),限制突发流量峰值。info-center filter
屏蔽非关键告警,减少日志干扰。通过以上措施可系统性定位并解决丢包率过高问题。若故障持续,建议收集 display diagnostic-information
输出并提交华三技术支持
(0)
当交换机日志显示IFMON_PKT_DROP_RATE_RISING报警,即接口丢包率超过告警阈值时,可以采取以下步骤进行排查和处理: 1. **查看丢包原因**:使用命令`display packet-drop interface`来检查接口的丢包原因。根据输出,可以判断是由于芯片缓存满(GBP full)、带宽不足(insufficient bandwidth)、入方向数据包过滤(Fast Filter Processor, FFP)或STP非转发状态(STP non-forwarding)导致的丢包。
(0)
暂无评论
这个日志来自 H3C 交换机,表示在 slot 1(槽位 1)的某个接口上,丢包率超过了设定的上限。
IFMON/4/IFMON_PKT_DROP_RATE_RISING:
The packet drop rate on slot 1 exceeds the upper threshold.
Threshold=1000, value=1665, interval=10s, protocol=30.
IFMON/4/IFMON_PKT_DROP_RATE_RISING
IFMON
(Interface Monitor):接口监控模块4
:告警级别(告警级别 4 = 警告)PKT_DROP_RATE_RISING
:丢包率上升slot 1
:指的是 槽位 1(如果是模块化交换机,可能是 1 号板卡的端口)。
Threshold=1000
:丢包率的上限阈值是 1000(通常是单位时间内丢失的报文数)。
value=1665
:当前的丢包率已达到 1665,超过了 1000 的阈值,触发告警。
interval=10s
:该统计是在 10 秒 内进行的,说明丢包率在 10 秒内较高。
protocol=30
:协议号 30(具体协议可能需要查询设备手册)。
display interface
命令检查端口 流量占用率:
display interface Ethernet1/0/1
重点关注:
Input queue drops
(输入丢包)Output queue drops
(输出丢包)Utilization
(利用率)display interface brief
display transceiver interface Ethernet1/0/1
display qos interface Ethernet1/0/1
display acl configuration
display cpu-usage
display interface Ethernet1/0/1
display transceiver interface Ethernet1/0/1
display qos interface Ethernet1/0/1
display acl configuration
display cpu-usage
如果 protocol=30
影响端口丢包,可尝试关闭相关协议:
undo xxx enable
(具体协议名称需确认)
display interface
、display cpu-usage
、display transceiver
等命令逐步排查。(0)
暂无评论
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明
暂无评论