插的10g光模块,接口下利用率显示100%,但速率只有8.6G,这是正常现象吗
Twenty-FiveGigE1/0/27
Current state: UP
Line protocol state: UP
IP packet frame type: Ethernet II, hardware address: 1484-7708-4876
Description: test
Bandwidth: 10000000 kbps
Loopback is not set
Media type is optical fiber, port hardware type is 10G_BASE_SR_SFP
FEC mode: None
10Gbps-speed mode, full-duplex mode
Link speed type is autonegotiation, link duplex type is autonegotiation
Flow-control is not enabled
Maximum frame length: 13312
Forbid jumbo frames to pass
Broadcast max-pps: 1000
Unknown-multicast max-pps: 1000
Unicast max-pps: 1000
Known-unicast max-ratio: 100%
PVID: 89
Port link-type: Trunk
VLAN Passing: 53, 89, 91-92, 99-100, 951
VLAN permitted: 53, 89, 91-92, 99-100, 951
Trunk port encapsulation: IEEE 802.1q
Port priority: 0
Last link flapping: 16 hours 29 minutes 59 seconds
Last clearing of counters: Never
Current system time:2025-06-05 09:53:19 beijing+08:00:00
Last time when physical state changed to up:2025-06-04 17:23:21 beijing+08:00:00
Last time when physical state changed to down:2025-06-04 17:23:20 beijing+08:00:00
Peak input rate: 1078777132 bytes/sec, at 2025-06-05 09:51:09
Peak output rate: 925532 bytes/sec, at 2025-05-12 19:44:36
Last 300 seconds input: 8561140 packets/sec 1078703948 bytes/sec 100%
Last 300 seconds output: 523 packets/sec 70553 bytes/sec 0%
Input (total): 60657066841 packets, 7980757986889 bytes
60656985397 unicasts, 280 broadcasts, 82698 multicasts, 0 pauses
Input (normal): 60657075279 packets, 7980759048439 bytes
60656992301 unicasts, 280 broadcasts, 82698 multicasts, 0 pauses
Input: 0 input errors, 0 runts, 0 giants, - throttles
0 CRC, - frame, 0 overruns, - aborts
- ignored, - parity errors
Output (total): 45123696 packets, 5172721089 bytes
13547428 unicasts, 1898689 broadcasts, 29677579 multicasts, 0 pauses
Output (normal): 45123697 packets, 5172721225 bytes
13547429 unicasts, 1898689 broadcasts, 29677579 multicasts, 0 pauses
Output: 0 output errors, 0 underruns, - buffer failures
- aborts, - deferred, - collisions, - late collisions
- lost carrier, - no carrier
(0)
最佳答案
正常的
这个命令统计是300S的
Last 300 seconds
(0)
这个命令 查询显示的300s 内的平均值;
(0)
300秒上面的不是最大速率吗,1078777132 bytes/sec也没有10g呀,主要他提示接口占用100%了,这个该怎么解释
300秒上面的不是最大速率吗,1078777132 bytes/sec也没有10g呀,主要他提示接口占用100%了,这个该怎么解释
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明
再看看端口下有什么特殊配置没