2台路由器堆叠,升级到Version 7.1.064, Release 6749P30的版本,备机一直重启是什么原因。
(0)
检查下日志进一步分析定位吧
比如备机版本是否同步升级成功等
(0)
主备机版本都是一样的,都升级了,只要一接堆叠线,备机就一直重启
是堆叠之后一起升级吗?
是否是升级时候只执行主框没有all main
例:
boot-loader file flash:/S5130EI_E-CMW710-R3208P10.ipe slot all main
这样可能导致你主备框版本不一致,堆叠起不来,备机一直重启,console单独进入备机确认下
确认下这个仅以下接口支持作为IRF物理端口: · MSR3610-X1、MSR3610-X1-DP、MSR3610-X1-DC、MSR3610-X1-DP-DC:GE0/0~GE0/5 · MSR3620-X1:仅XGE0/16~XGE0/17 · MSR3640-X1:仅GE0/0、XGE0/9~XGE0/11
如图1-14所示,配置Device A和Device B组成IRF设备。由于IRF到中间设备Device C有跨成员设备的聚合链路,且Device C为支持LACP协议的H3C设备,配置LACP MAD进行分裂检测。
图1-14 IRF典型配置组网图(LACP MAD检测方式)
设备出厂为独立运行模式,为减少IRF搭建过程中设备重启的次数,本举例采用以下配置思路:
(1) 在独立运行模式下,完成IRF端口和参数的配置。
(2) 切换到IRF模式,在设备重启过程中,连接IRF物理接口。设备启动完成,IRF搭建成功。
(3) 配置MAD检测。
如果您采用先将设备切换到IRF模式,再绑定IRF端口的方式搭建IRF。请在完成IRF端口等参数配置后,执行save命令保存当前配置,再执行irf-port-configuration active命令手工激活IRF端口的配置,才能形成IRF。
(1) 搭建IRF(Device A上的配置)
# 配置Device A的成员编号为1,创建IRF端口2,并将它与物理端口GigabitEthernet0/1和GigabitEthernet0/3绑定。
<Sysname> system-view
[Sysname] irf member 1
[Sysname] irf-port 2
[Sysname-irf-port2] port group interface GigabitEthernet 0/1
[Sysname-irf-port2] port group interface GigabitEthernet 0/3
[Sysname-irf-port2] quit
# 将当前配置保存到下次启动配置文件。
[Sysname] quit
<Sysname> save
# 将设备的运行模式切换到IRF模式。
<Sysname> system-view
[Sysname] chassis convert mode irf
The device will switch to IRF mode and reboot.
You are recommended to save the current running configuration and specify the configuration file for the next startup. Continue? [Y/N]:y
Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
flash:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait...
Saved the current configuration to mainboard device successfully.
Slot 1:
Save next configuration file successfully.
Do you want to convert the content of the next startup configuration file flash:/startup.cfg to make it available in IRF mode? [Y/N]:y
Now rebooting, please wait...
设备重启后Device A组成了只有一台成员设备的IRF。
(2) 搭建IRF(Device B上的配置)
# 配置Device B的成员编号为2,创建IRF端口1,并将它与物理端口GigabitEthernet0/1和GigabitEthernet0/3绑定。
<Sysname> system-view
[Sysname] irf member 2
[Sysname] irf-port 1
[Sysname-irf-port1] port group interface GigabitEthernet 0/1
[Sysname-irf-port1] port group interface GigabitEthernet 0/3
[Sysname-irf-port1] quit
# 将当前配置保存到下次启动配置文件。
[Sysname] quit
<Sysname> save
# 参考图1-14进行物理连线。
# 将设备的运行模式切换到IRF模式。
<Sysname> system-view
[Sysname] chassis convert mode irf
The device will switch to IRF mode and reboot.
You are recommended to save the current running configuration and specify the configuration file for the next startup. Continue? [Y/N]:y
Please input the file name(*.cfg)[flash:/startup.cfg]
(To leave the existing filename unchanged, press the enter key):
flash:/startup.cfg exists, overwrite? [Y/N]:y
Validating file. Please wait...
Saved the current configuration to mainboard device successfully.
Slot 1:
Save next configuration file successfully.
Do you want to convert the content of the next startup configuration file flash:/startup.cfg to make it available in IRF mode? [Y/N]:y
Now rebooting, please wait...
设备B重启后与设备A形成IRF。
(0)
堆叠配置例子我也更新了,你对下操作流程
主备机版本都是一样的,都升级了,只要一接堆叠线,备机就一直重启
确认下这个仅以下接口支持作为IRF物理端口: · MSR3610-X1、MSR3610-X1-DP、MSR3610-X1-DC、MSR3610-X1-DP-DC:GE0/0~GE0/5 · MSR3620-X1:仅XGE0/16~XGE0/17 · MSR3640-X1:仅GE0/0、XGE0/9~XGE0/11
堆叠配置例子我也更新了,你对下操作流程
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明
打个400或联系供应商技术支持看下日志进一步定位吧。光目前信息没辙