一开启二层远程镜像,通过这台交换机转发的流量,丢包很严重(10.68.11.168 ping 10.168.11.1丢包9%),一取消该镜像配置,网络就恢复了。流统显示丢包在设备上。
1、检查镜像相关配置:
#
mirroring-group 4 remote-source
mirroring-group 4 remote-probe vlan 3
#
#
interface GigabitEthernet1/3/0/13
port link-mode bridge
description ##link-to-shizhengfu-neiwanghexin##
port link-type trunk
port trunk permit vlan 1 to 2 4 to 4094
qos apply policy lt inbound
qos apply policy lt outbound
mirroring-group 4 mirroring-port both
#
#
interface GigabitEthernet1/3/0/14
port link-mode bridge
stp disable
mirroring-group 4 reflector-port
#
#
interface GigabitEthernet1/3/0/26
port link-mode bridge
description link to lvmeng jingxiang
port access vlan 3
#
#
interface GigabitEthernet1/3/0/15
port link-mode bridge
description link to tianrongxin jingxiang
port access vlan 3
#
检查镜像相关限制:
· EA、SA类型单板的端口不支持被配置成为反射口。
· 镜像反射口必须是Access类型的端口,且必须属于缺省VLAN(VLAN1)。
· 建议选择设备上未使用的端口作为镜像反射口,且建议关闭反射口的生成树协议。
· Combo端口不能被配置为镜像反射口。
· 一个镜像组内可以配置多个源端口。
· 请不要将源端口加入到远程镜像VLAN中,否则会影响镜像功能的正常使用。
· 在一个镜像组内,如果已经配置了镜像反射口,则无法再配置镜像出端口。
· 一个VLAN只能作为一个远程源镜像组的远程镜像VLAN,且建议该VLAN只用于端口镜像,请不要在该VLAN上配置其它业务功能或创建对应的VLAN接口。
· 远程镜像VLAN必须为静态VLAN,且在被配置成远程镜像VLAN后,该VLAN不能直接删除,必须先删除远程镜像VLAN的配置才能够删除这个VLAN。
· 如果镜像组生效后,远程镜像VLAN被取消,那么该镜像组将失效。
· 镜像目的端口必须是Access类型的端口。
#
interface GigabitEthernet1/3/0/14
port link-mode bridge
stp disable
mirroring-group 4 reflector-port
#
===============display device verbose===============
==========================================================
Chassis Slot Type State Subslot Soft Ver Patch Ver
1 0 LSQ1SRPB Master 0 S7500E-6710P03 None
1 1 NONE Absent 0 NONE None
1 2 LSQ1GV48SA Normal 0 S7500E-6710P03 None
1 3 LSQ1GV24PSA Normal 0 S7500E-6710P03 None
1 4 LSQ1TGS8SC Normal 0 S7500E-6710P03 None
2 0 LSQ1SRPB Slave 0 S7500E-6710P03 None
2 1 NONE Absent 0 NONE None
2 2 LSQ1GV48SA Normal 0 S7500E-6710P03 None
2 3 LSQ1GV24PSC Normal 0 S7500E-6710P03 None
2 4 LSQ1TGS8SC Normal 0 S7500E-6710P03 None
将反射口配置到SC单板后解决。
该案例暂时没有网友评论
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作