12508>dis int brief | in NCS
HGE1/2/0/2 UP UP 220.185.63.198
HGE1/2/0/3 UP UP 220.185.63.182
HGE1/2/0/4 UP UP 220.185.63.186
HGE1/2/0/5 UP UP 220.185.63.194
HGE2/2/0/1 UP UP 220.185.63.190
HGE2/2/0/3 UP UP 220.185.63.210
HGE2/2/0/4 UP UP 220.185.63.202
HGE2/2/0/5 DOWN DOWN 220.185.63.206
Configure load balancing in the EBGP IPV4 address family as follows, used to advertise two default routes to 12508,
12508 configuration
peer 61.130.158.1 as-number 136190
peer 61.130.158.1 group pgJHIDC
peer 61.130.158.1
peer 61.130.159.1 as-number 136190
address-family ipv4 unicast
dampening
balance ebgp 8 \\The relevant explanation is: https://www.h3c.com/cn/d_202001/1259040_30005_0.htm#aa_15
preference 20 200 200
But after configuring load balancing, check the routing table and see that there are only two interfaces for the next hop interface
S12508>dis ip routing-table 0.0.0.0
Summary Count: 2
Destination/Mask Proto Pre Cost NextHop Interface
0.0.0.0/0 BGP 20 0 61.130.158.1 HGE1/2/0/4
0.0.0.0/0 BGP 20 0 61.130.159.1 HGE2/2/0/4
View the BGP routing table,
<S12508>dis bgp routing-table ipv4 0.0.0.0
BGP local router ID: 220.185.58.223
Local AS number: 65140
Paths: 2 available, 2 best
BGP routing table information of 0.0.0.0/0:
From: 61.130.158.1 (61.130.158.1)
Relay nexthop: 220.185.63.185
Original nexthop: 61.130.158.1
OutLabel: NULL
AS-path: 136190 4134
Origin: igp
Attribute value: pref-val 0
State: valid, external, best,
From: 61.130.159.1 (61.130.159.1)
Relay nexthop: 220.185.63.181
Original nexthop: 61.130.159.1
OutLabel: NULL
AS-path: 136190 4134
Origin: igp
Attribute value: pref-val 0
State: valid, external, best,
The current temporary replacement using eight default routes is not convenient for testing.
The following are manually configured static routes:
<S12508>display ip routing-table 0.0.0.0
Summary Count: 9
Destination/Mask Proto Pre Cost NextHop Interface
0.0.0.0/0 Static 10 0 220.185.63.181 HGE1/2/0/3
220.185.63.185 HGE1/2/0/4
220.185.63.189 HGE2/2/0/1
220.185.63.193 HGE1/2/0/5
220.185.63.197 HGE1/2/0/2
220.185.63.201 HGE2/2/0/4
220.185.63.205 HGE2/2/0/5
220.185.63.209 HGE2/2/0/3
You can display fib 0.0.0.0 0 to see if there are 8 next hops in the default route.
The next hop in the ip routing table that iterates through EBGP routes on our device shows the next hop before the iteration.
The next hop is the loopback address of the NCS. When it is actually forwarded, it will iterate to the remaining interfaces. fib table view.
This phenomenon is normal.
The display result of the current version of the platform is before the iteration. There are mentions of demand rectification. After E3603P01, it is the display result of B75 rectification.
No comments
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作