Null
现场使用MSR3610设备与思科设备帧中继对接无法互通,配置完成。测试连通性的时候出现了串口物理层和协议层均up,但是无法ping通对端设备的故障现象。
1、首先查看接口状态,Serial1/1口物理层和协议层均up
[route-Serial1/1]dis ip int br
*down: administratively down
(s): spoofing (l): loopback
Interface Physical Protocol IP Address Description
GE0/0 up up 198.xxx.xx.31 --
GE0/1 *down down 9.xx.xxx.210 --
GE0/2 down down -- --
…….
Ser1/0 down down -- --
Ser1/1 up up 144.xx.xxx.10 --
2、其次,检查接口配置暂时没有发现问题:
[route-Serial1/1]dis cur int se 1/1
#
interface Serial1/1
description yinlian
link-protocol fr
fr lmi type ansi
fr map ip 144.xx.xxx.9 101
#
fr dlci 101
broadcast
ip address 144.xx.xxx.10 255.255.255.252
#
return
Ping对端同网段地址无法ping通
[tc_wt-Serial1/1]ping 144.xx.xxx.9
Ping 144.xx.xxx.9 ( 144.xx.xxx.9 ): 56 data bytes, press CTRL_C to break
Request time out
Request time out
……
3、针对帧中继链路层协议处于up状态,但不能ping通对方的问题,我们应该确认两端设备地址映射配置是否正确或者路由是否可达。
而现场配置正常且路由也已正常,因此排除这两个问题。
4、查看接口信息,发现接口入方向有大量error错包且有增长:
Serial1/1
Current state: UP
Line protocol state: UP
Link layer protocol is FR IETF
LMI DLCI is 0, LMI type is ANSI, frame relay DTE
LMI status enquiry sent 3, LMI status received 3
LMI status timeout 0, LMI message discarded 0
Physical layer: synchronous, Virtual baudrate: 64000 bps
……
Interface: DTE
Cable type: V35
Clock mode: DTECLK1
Last 300 seconds input rate: 0.00 bytes/sec, 0 bits/sec, 0.00 packets/sec
Last 300 seconds output rate: 0.00 bytes/sec, 0 bits/sec, 0.00 packets/sec
Input:
3 packets, 52 bytes
0 broadcasts, 0 multicasts
5270 errors, 0 runts, 0 giants
0 CRC, 0 align errors, 0 overruns
5270 aborts, 0 no buffers, 0 frame errors
Output:
3 packets, 42 bytes
0 errors, 0 underruns, 0 collisions
0 deferred
一般情况下,如果说入方向上有error错包的话,大概率是由于时钟问题引起的。
invert receive-clock:是为了消除线路上半个时钟周期的时延,可以将DTE侧同步串口的接收时钟信号翻转。
测试所有接口配置上这个命令之后,均能正常的up起来,与对端互ping可以通。
接口下配置invert receive-clock后问题解决。
该案例暂时没有网友评论
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作