• 全部
  • 经验案例
  • 典型配置
  • 技术公告
  • FAQ
  • 全部
  • 全部
产品线
搜索
取消
案例类型
发布者
是否解决
是否官方
时间
高级搜索

某局点S7610设备接口up down震荡未记录案例

2020-11-08 发表
  • 0关注
  • 0收藏,84浏览
粉丝:14人 关注:7人

组网及说明

问题描述

10.29日上午9:18分设备端口down up 了一次。

%Oct 29 09:18:14:211 2020 S7610 LAGG/6/LAGG_INACTIVE_PARTNER: Member port XGE0/0/3 of aggregation group BAGG2 changed to the inactive state, because the aggregation configuration of its peer port is incorrect.

%Oct 29 09:18:14:229 2020 S7610 IFNET/5/LINK_UPDOWN: Line protocol state on the interface Ten-GigabitEthernet0/0/3 changed to down.

%Oct 29 09:18:14:236 2020 S7610 IFNET/3/PHY_UPDOWN: Physical state on the interface Bridge-Aggregation2 changed to down.

%Oct 29 09:18:14:236 2020 S7610 IFNET/5/LINK_UPDOWN: Line protocol state on the interface Bridge-Aggregation2 changed to down.

%Oct 29 09:18:15:110 2020 S7610 LAGG/6/LAGG_ACTIVE: Member port XGE0/0/3 of aggregation group BAGG2 changed to the active state.

%Oct 29 09:18:15:126 2020 S7610 IFNET/5/LINK_UPDOWN: Line protocol state on the interface Ten-GigabitEthernet0/0/3 changed to up.

%Oct 29 09:18:15:147 2020 S7610 IFNET/3/PHY_UPDOWN: Physical state on the interface Bridge-Aggregation2 changed to up.

 

而接口下接口下记录的最后一次down up的时间是10.28日下午的down up 记录:

Ten-GigabitEthernet0/0/3

Current state: UP

Line protocol state: UP

IP packet frame type: Ethernet II, hardware address: 84d9-3137-1e00

Description: to BC_BC_ME60-X8_10G_GE2/1/3

Bandwidth: 10000000 kbps

Loopback is not set

Media type is optical fiber, port hardware type is 10G_BASE_ER_SFP

10Gbps-speed mode, full-duplex mode

Link speed type is autonegotiation, link duplex type is autonegotiation

Flow-control is not enabled

Maximum frame length: 9216

Allow jumbo frames to pass

Broadcast max-ratio: 100%

Multicast max-ratio: 100%

Unicast max-ratio: 100%

PVID: 1

MDI type: Automdix

Link-down delay is 3s, link-up delay is 3s

Port link-type: Trunk

VLAN Passing:   1001-2000, 3602, 3845-3899, 4000-4045

VLAN permitted: 1001-2000, 3602, 3845-3899, 4000-4045

Trunk port encapsulation: IEEE 802.1q

Port priority: 0

Last link flapping: 17 hours 27 minutes 17 seconds

Last clearing of counters: Never

Current system time:2020-10-29 10:02:49 China+08:00:00

Last time when physical state changed to up:2020-10-28 16:35:31 China+08:00:00

Last time when physical state changed to down:2020-10-28 16:34:53 China+08:00:00

Peak input rate: 674173395 bytes/sec, at 2020-09-26 21:55:01

 Peak output rate: 198728771 bytes/sec, at 2020-09-14 21:02:10

 Last 300 seconds input: 151930 packets/sec 177729250 bytes/sec 14%

Last 300 seconds output: 103243 packets/sec 46300011 bytes/sec 4%

Input (total):  948030105098 packets, 1099317284012196 bytes

         948027729299 unicasts, 0 broadcasts, 145466 multicasts, 0 pauses

Input (normal):  948027874765 packets, - bytes

         948027729299 unicasts, 0 broadcasts, 145466 multicasts, 0 pauses

Input:  2227928 input errors, 7439 runts, 0 giants, 0 throttles

         2220489 CRC, 0 frame, - overruns, 5446 aborts

         - ignored, - parity errors

Output (total): 620434871236 packets, 289586298121410 bytes

         620409619638 unicasts, 16446638 broadcasts, 8804960 multicasts, 0 pauses

Output (normal): 620434871236 packets, - bytes

         620409619638 unicasts, 16446638 broadcasts, 8804960 multicasts, 0 pauses

Output: 0 output errors, - underruns, - buffer failures

         0 aborts, 0 deferred, 0 collisions, 0 late collisions

         0 lost carrier, - no carrier

 

 经确认,

10.28日下午接口确实down up过的接口震荡信息:

%Oct 28 16:34:54:063 2020 S7610 IFNET/3/PHY_UPDOWN: Physical state on the interface Bridge-Aggregation2 changed to down.

%Oct 28 16:34:54:067 2020 S7610 IFNET/5/LINK_UPDOWN: Line protocol state on the interface Bridge-Aggregation2 changed to down.

%Oct 28 16:35:31:367 2020 S7610 IFNET/3/PHY_UPDOWN: Physical state on the interface Ten-GigabitEthernet0/0/3 changed to up.

%Oct 28 16:35:31:395 2020 S7610 LAGG/6/LAGG_ACTIVE: Member port XGE0/0/3 of aggregation group BAGG2 changed to the active state.

%Oct 28 16:35:31:413 2020 S7610 IFNET/5/LINK_UPDOWN: Line protocol state on the interface Ten-GigabitEthernet0/0/3 changed to up.

%Oct 28 16:35:31:424 2020 S7610 IFNET/3/PHY_UPDOWN: Physical state on the interface Bridge-Aggregation2 changed to up.


为什么接口没有记录下10.29日上午的震荡信息呢?


过程分析

1.    两次log 打印不一样。

 

1次, 有端口 Physical state down 打印, down 时间接近 30 秒, 远远大于 3 秒的 link delay up

%Oct 28 16:34:53:990 2020 S7610 IFNET/3/PHY_UPDOWN: Physical state on the interface Ten-GigabitEthernet0/0/3 changed to down.

%Oct 28 16:34:54:023 2020 S7610 IFNET/5/LINK_UPDOWN: Line protocol state on the interface Ten-GigabitEthernet0/0/3 changed to down.

%Oct 28 16:35:31:367 2020 S7610 IFNET/3/PHY_UPDOWN: Physical state on the interface Ten-GigabitEthernet0/0/3 changed to up.

%Oct 28 16:35:31:413 2020  S7610 IFNET/5/LINK_UPDOWN: Line protocol state on the interface Ten-GigabitEthernet0/0/3 changed to up.

 

2次,没有 Physical state down 打印, down 时间只有持续了 1 秒, 小于 3 秒的 link delay 3 值。 产品没有向上报 端口 link down 事件。

%Oct 29 09:18:14:229 2020  S7610 IFNET/5/LINK_UPDOWN: Line protocol state on the interface Ten-GigabitEthernet0/0/3 changed to down.

%Oct 29 09:18:14:236 2020  S7610 IFNET/3/PHY_UPDOWN: Physical state on the interface Bridge-Aggregation2 changed to down.

%Oct 29 09:18:14:236 2020 S7610 IFNET/5/LINK_UPDOWN: Line protocol state on the interface Bridge-Aggregation2 changed to down.

%Oct 29 09:18:15:110 2020 S7610 LAGG/6/LAGG_ACTIVE: Member port XGE0/0/3 of aggregation group BAGG2 changed to the active state.

%Oct 29 09:18:15:126 2020  S7610 IFNET/5/LINK_UPDOWN: Line protocol state on the interface Ten-GigabitEthernet0/0/3 changed to up.

 

 

接口下记录:Ten-GigabitEthernet0/0/3 显示的是 Physical state up / down 的时间

Last time when physical state changed to up:2020-10-28 16:35:31 China+08:00:00

Last time when physical state changed to down:2020-10-28 16:34:53 China+08:00:00

解决方法

【结论】 正常情况;

只记录物理的down up时间,不记录由于协议引起的down up。

0 个评论

该案例暂时没有网友评论

编辑评论

举报

×

侵犯我的权益 >
对根叔知了社区有害的内容 >
辱骂、歧视、挑衅等(不友善)

侵犯我的权益

×

泄露了我的隐私 >
侵犯了我企业的权益 >
抄袭了我的内容 >
诽谤我 >
辱骂、歧视、挑衅等(不友善)
骚扰我

泄露了我的隐私

×

您好,当您发现根叔知了上有泄漏您隐私的内容时,您可以向根叔知了进行举报。 请您把以下内容通过邮件发送到zhiliao@h3c.com 邮箱,我们会尽快处理。
  • 1. 您认为哪些内容泄露了您的隐私?(请在邮件中列出您举报的内容、链接地址,并给出简短的说明)
  • 2. 您是谁?(身份证明材料,可以是身份证或护照等证件)

侵犯了我企业的权益

×

您好,当您发现根叔知了上有关于您企业的造谣与诽谤、商业侵权等内容时,您可以向根叔知了进行举报。 请您把以下内容通过邮件发送到 zhiliao@h3c.com 邮箱,我们会在审核后尽快给您答复。
  • 1. 您举报的内容是什么?(请在邮件中列出您举报的内容和链接地址)
  • 2. 您是谁?(身份证明材料,可以是身份证或护照等证件)
  • 3. 是哪家企业?(营业执照,单位登记证明等证件)
  • 4. 您与该企业的关系是?(您是企业法人或被授权人,需提供企业委托授权书)
我们认为知名企业应该坦然接受公众讨论,对于答案中不准确的部分,我们欢迎您以正式或非正式身份在根叔知了上进行澄清。

抄袭了我的内容

×

原文链接或出处

诽谤我

×

您好,当您发现根叔知了上有诽谤您的内容时,您可以向根叔知了进行举报。 请您把以下内容通过邮件发送到zhiliao@h3c.com 邮箱,我们会尽快处理。
  • 1. 您举报的内容以及侵犯了您什么权益?(请在邮件中列出您举报的内容、链接地址,并给出简短的说明)
  • 2. 您是谁?(身份证明材料,可以是身份证或护照等证件)
我们认为知名企业应该坦然接受公众讨论,对于答案中不准确的部分,我们欢迎您以正式或非正式身份在根叔知了上进行澄清。

对根叔知了社区有害的内容

×

垃圾广告信息
色情、暴力、血腥等违反法律法规的内容
政治敏感
不规范转载 >
辱骂、歧视、挑衅等(不友善)
骚扰我
诱导投票

不规范转载

×

举报说明

提出建议

    +
<

亲~登录后才可以操作哦!

确定

你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作