H3C无线接入点V7AP胖模式切换成瘦模式的经验案例

 现场WA5530结合V7 AC（WX5540H）部署，一直无法注册成功。工程师console登录AP后，发现是胖模式，版本是Version 7.1.064, ESS 2329P01，现在配合AC使用必须将AP切换成瘦模式。

//连接console线，使用CRT或者超级终端新建serial（串口）连接，AP上电启动，console登录到AP上

System is starting...

Press Ctrl+D to access BASIC-BOOTWARE MENU

Booting Normal Extended BootWare

The Extended BootWare is self-decompressing.................................

...Done.   //不停地按Ctrl+B

*********************************************************************

*                                                                   *

*                   H3C WA5530 BootWare, Version 7.10               *

*                                                                   *

*********************************************************************

Copyright (c) 2004-2017 New H3C Technologies Co., Ltd.

 

Compiled Date       : Sep 25 2017

CPU Type            : ARM

CPU L1 Cache        : 32KB

CPU L2 Cache        : 256KB

CPU Clock Speed     : 710MHz

Memory Type         : DDR3 SDRAM

Memory Size         : 512MB

Memory Speed        : 667MHz

Flash Size          : 128MB

PCB Version         : Ver.A

 

 

BootWare Validating...

Press Ctrl+B to access EXTENDED-BOOTWARE MENU...

 

Password recovery capability is enabled.

Note: The current operating device is flash

Enter < Storage Device Operation > to select device.  //输入回车

 

==========================<EXTENDED-BOOTWARE MENU>===================

|<1> Boot System                                                    |

|<2> Enter Serial SubMenu                                           |

|<3> Enter Ethernet SubMenu                                         |

|<4> File Control                                                   |

|<5> Restore to Factory Default Configuration                       |

|<6> Skip Current System Configuration                              |

|<7> BootWare Operation Menu                                        |

|<8> Skip Authentication for Console Login                          |

|<9> Storage Device Operation                                       |

|<0> Reboot                                                         |

=====================================================================

Ctrl+Z: Access EXTENDED ASSISTANT MENU

Ctrl+F: Format File System

Ctrl+C: Display Copyright

Ctrl+Y: Change AP Mode

Enter your choice(0-9):  //输入Ctrl+F，格式化flash

Warning:All files on flash will be lost! Are you sure to format? [Y/N]Y //输入Y

............................................................................

...............................................

Format success.

 

==========================<EXTENDED-BOOTWARE MENU>===================

|<1> Boot System                                                    |

|<2> Enter Serial SubMenu                                           |

|<3> Enter Ethernet SubMenu                                         |

|<4> File Control                                                   |

|<5> Restore to Factory Default Configuration                       |

|<6> Skip Current System Configuration                              |

|<7> BootWare Operation Menu                                        |

|<8> Skip Authentication for Console Login                          |

|<9> Storage Device Operation                                       |

|<0> Reboot                                                         |

=====================================================================

Ctrl+Z: Access EXTENDED ASSISTANT MENU

Ctrl+F: Format File System

Ctrl+C: Display Copyright

Ctrl+Y: Change AP Mode

Enter your choice(0-9):  //输入Ctrl+Y，设置ap胖模式或者瘦模式

 

Please select the new mode

Current mode is Fat  //提示当前是fat胖模式

=====================================================================

|NO.  Mode                                                          |

|1    Fat Mode                                                      |

|2    Fit Mode                                                      |

|0    Exit                                                          |

=====================================================================

Enter your choice(0-2):2   //输入2，即fit瘦模式

 

 

Warning:Change from fat mode to fit mode formats the storage medium! Are

you sure to continue ? [Y/N]Y  //输入Y，确认切换成fit瘦模式......................................................................................

Formatted the storage medium successfully!

Changed to fit mode successfully!  //修改成fit瘦模式成功。此时可以将AP和AC连接好，AP上电启动获取IP地址后，会主动向AC获取版本文件更新到flash中运行。另外一种方式，从AC的flash apimge目录下导出wa5300.ipe文件手工传到AP上，具体步骤如下

 

==========================<EXTENDED-BOOTWARE MENU>===================

|<1> Boot System                                                    |

|<2> Enter Serial SubMenu                                           |

|<3> Enter Ethernet SubMenu                                         |

|<4> File Control                                                   |

|<5> Restore to Factory Default Configuration                       |

|<6> Skip Current System Configuration                              |

|<7> BootWare Operation Menu                                        |

|<8> Skip Authentication for Console Login                          |

|<9> Storage Device Operation                                       |

|<0> Reboot                                                         |

=====================================================================

Ctrl+Z: Access EXTENDED ASSISTANT MENU

Ctrl+F: Format File System

Ctrl+C: Display Copyright

Ctrl+Y: Change AP Mode

Enter your choice(0-9): 3  //进入以太口子菜单

 

==========================<Enter Ethernet SubMenu>===================

|Note:the operating device is flash                                 |

|<1> Download Image Program To SDRAM And Run                        |

|<2> Update Main Image File                                         |

|<3> Update Backup Image File                                       |

|<4> Download Files(*.*)                                            |

|<5> Modify Ethernet Parameter                                      |

|<0> Exit To Main Menu                                              |

|<Ensure The Parameter Be Modified Before Downloading!>             |

=====================================================================

Enter your choice(0-5): 5  //修改以太口参数

 

==========================<ETHERNET PARAMETER SET>===================

|Note:       &＃39;.&＃39; = Clear field.                                     |

|            &＃39;-&＃39; = Go to previous field.                            |

|         Ctrl+D = Quit.                                            |

=====================================================================

Protocol (FTP or TFTP) :ftp  tftp   //tftp协议

Load File Name         :wa5300-fat.ipe

                       :wa5300.ipe  //瘦版本文件名称

Target File Name       :wa5300-fat.ipe

                       :wa5300.ipe   //瘦版本文件名称

Server IP Address      :192.168.1.18   192.168.0.10  //tftp服务器（PC）的IP地址

Local IP Address       :192.168.1.20   192.168.0.50  //AP本地的IP地址

Subnet Mask            :255.255.255.0  255.255.255.0 //掩码

Gateway IP Address     :0.0.0.0    //不用输，直接回车

 

 

==========================<Enter Ethernet SubMenu>===================

|Note:the operating device is flash                                 |

|<1> Download Image Program To SDRAM And Run                        |

|<2> Update Main Image File                                         |

|<3> Update Backup Image File                                       |

|<4> Download Files(*.*)                                            |

|<5> Modify Ethernet Parameter                                      |

|<0> Exit To Main Menu                                              |

|<Ensure The Parameter Be Modified Before Downloading!>             |

============================================================================

Enter your choice(0-5): 2  //输入2，更新主镜像文件（更新版本）

Loading.................................................................................................................................Done.

18165760 bytes downloaded!

Image file wa5300-boot.bin is self-decompressing...

Saving file flash:/wa5300-boot.bin .............Done.

Image file wa5300-system.bin is self-decompressing...

Saving file flash:/wa5300-system.bin .......................................

Done.

 

==========================<Enter Ethernet SubMenu>===================

|Note:the operating device is flash                                 |

|<1> Download Image Program To SDRAM And Run                        |

|<2> Update Main Image File                                         |

|<3> Update Backup Image File                                       |

|<4> Download Files(*.*)                                            |

|<5> Modify Ethernet Parameter                                      |

|<0> Exit To Main Menu                                              |

|<Ensure The Parameter Be Modified Before Downloading!>             |

=====================================================================

Enter your choice(0-5): 0  //输入0，返回

 

==========================<EXTENDED-BOOTWARE MENU>===================

|<1> Boot System                                                    |

|<2> Enter Serial SubMenu                                           |

|<3> Enter Ethernet SubMenu                                         |

|<4> File Control                                                   |

|<5> Restore to Factory Default Configuration                       |

|<6> Skip Current System Configuration                              |

|<7> BootWare Operation Menu                                        |

|<8> Skip Authentication for Console Login                          |

|<9> Storage Device Operation                                       |

|<0> Reboot                                                         |

=====================================================================

Ctrl+Z: Access EXTENDED ASSISTANT MENU

Ctrl+F: Format File System

Ctrl+C: Display Copyright

Ctrl+Y: Change AP Mode

Enter your choice(0-9): 0  //输入0，重启AP

System is starting...

Press Ctrl+D to access BASIC-BOOTWARE MENU

Booting Normal Extended BootWare

The Extended BootWare is self-decompressing.................................

...Done.

 

*********************************************************************

*                                                                   *

*                   H3C WA5530 BootWare, Version 7.10               *

*                                                                   *

*********************************************************************

Copyright (c) 2004-2017 New H3C Technologies Co., Ltd.

 

Compiled Date       : Sep 25 2017

CPU Type            : ARM

CPU L1 Cache        : 32KB

CPU L2 Cache        : 256KB

CPU Clock Speed     : 710MHz

Memory Type         : DDR3 SDRAM

Memory Size         : 512MB

Memory Speed        : 667MHz

Flash Size          : 128MB

PCB Version         : Ver.A

 

 

BootWare Validating...

Press Ctrl+B to access EXTENDED-BOOTWARE MENU...

Loading the main image files...

Loading file flash:/wa5300-system.bin................Done.

Loading file flash:/wa5300-boot.bin.......Done.

 

Extended BootWare Version is not equal,updating? [Y/N]

Updating Extended BootWare.........Done.

BootWare updated,System is rebooting now.

System is starting...

Press Ctrl+D to access BASIC-BOOTWARE MENU

Booting Normal Extended BootWare

The Extended BootWare is self-decompressing.................................

...Done.

 

*********************************************************************

*                                                                   *

*                   H3C WA5530 BootWare, Version 7.09               *

*                                                                   *

*********************************************************************

Copyright (c) 2004-2017 New H3C Technologies Co., Ltd.

 

Compiled Date       : Jun 23 2017

CPU Type            : ARM

CPU L1 Cache        : 32KB

CPU L2 Cache        : 256KB

CPU Clock Speed     : 710MHz

Memory Type         : DDR3 SDRAM

Memory Size         : 512MB

Memory Speed        : 667MHz

Flash Size          : 128MB

PCB Version         : Ver.A

 

 

BootWare Validating...

Press Ctrl+B to access EXTENDED-BOOTWARE MENU...

Loading the main image files...

Loading file flash:/wa5300-system.bin................Done.

Loading file flash:/wa5300-boot.bin.......Done.

 

Image file flash:/wa5300-boot.bin is self-decompressing............................................................................................................................Done.

System image is starting...

 

Startup configuration file does not exist.

Line con0 is available.

 

Press ENTER to get started.

 

<H3C>   //升级成功

%Dec 15 18:56:11:669 2017 H3C SHELL/5/SHELL_LOGIN: Console logged in from con0.

先Ctrl+F格式化flash，再Ctrl+Y选择瘦模式，最后加载版本。