HPE ProLiant Host Bus Adapters - HPE 服务器中的 Emulex HBA 可能无法在开机时建立光纤通道链路，从而阻止 SAN 启动

HPE ProLiant Host Bus Adapters - Emulex HBAs in HPE Servers May Fail to Establish Fibre Channel Link at Power ON, Preventing SAN Boot

文档ID：a00154203en_us    Last Updated: 2025-10-02

影响范围

配置如下HBA卡：

• HPE SN1200E 16Gb Dual Port Fibre Channel Host Bus Adapter (Q0L14A)
• HPE SN1200E 16Gb Single Port Fibre Channel Host Bus Adapter (Q0L13A)
• HPE SN1600E 32Gb Dual Port Fibre Channel Host Bus Adapter (Q0L12A)
• HPE SN1600E 32Gb Single Port Fibre Channel Host Bus Adapter (Q0L11A)
• HPE SN1610E 32Gb 1-port Fibre Channel Host Bus Adapter (R2J62A)
• HPE SN1610E 32Gb 2-port Fibre Channel Host Bus Adapter (R2J63A)
• HPE SN1620E 32Gb 2-port Fibre Channel Secure Host Bus Adapter (S4S01A)
• HPE SN1700E 64Gb 1-port Fibre Channel Host Bus Adapter (R7N77A)
• HPE SN1700E 64Gb Fibre Channel Host Bus Adapter (HPESN1700E64FCHBAPRE)
• HPE SN1720E 64Gb 2-port Fibre Channel Secure Host Bus Adapter (S4T09A)

HBA卡更新固件到14.4.473.14版本后，HPE 服务器中的某些 Emulex HBA可能无法从 SAN 启动。此问题是由于HBA固件无法激活光纤通道端口，导致主机无法登录光纤通道目标。

识别此问题需要检查物理HBA卡上Link LED情况，是否有哪个口不发光。此外，当服务器处于RBSU中时，即使 BIOS HBA驱动程序功能已启用， HBA BIOS 信息仍会显示端口链路状态为“关闭”。光纤通道交换机也无法检测到已登录的 HBA  WWPN。如果采用“直连式”光纤通道存储配置，HBA 将无法与存储设备建立链接。

POST期间连接失败时记录了以下IML错误消息：

Critical,690,5311,0x0011,Network,0x000D,Hardware,11/22/2024 11:27:47,1652: All links are down in adapter HPE SN1610E 32Gb 2p FC HBA in slot 1 ACTION: Check the connection to the adapter and validate the connectivity from the server to any external device, including the cabling. If no problems are found, the adapter or other connectivity device may need replacement.

N/A

此问题在HPE Fibre Channel Emulex Host Bus Adapters的 14.4.473.30 版本解决，该版本允许主机能够在服务器开机时开启光纤通道端口连接。该固件可从以下链接下载：

• HPE Firmware Flash for Emulex 32Gb and 64Gb Fibre Channel Host Bus Adapters version 14.4.473.30(或更高)
• HPE Firmware Flash for Emulex Fibre Channel Host Bus Adapters for VMware vSphere 8.0 version 2025.09.01(或更高)