某客户局点在S7506E三层接口下配置策略路由,系统提示不支持。
[SWITCH-Vlan-interface33]ip policy-based-route
testPT
Error: The operation is not supported.
查看设备日志,PBR无法正常下发:查看配置
%May 10 08:22:52:466 2018 SWITCH
SHELL/6/SHELL_CMD: -Task=vt0-IPAddr=192.168.1.1-User=admin; Command is ip policy-based-route
testPT
%May 10 08:22:52:469 2018 SWITCH PBR/5/PBR_DRIVER_NOT_SUPPORT:
-Chassis=1-Slot=0; Driver cannot support the operation.
%May 10 08:22:52:469 2018 SWITCH PBR/5/PBR_DRIVER_NOT_SUPPORT:
-Chassis=1-Slot=1; Driver cannot support the operation.
%May 10 08:22:52:473 2018 SWITCH PBR/5/PBR_DRIVER_NOT_SUPPORT:
-Chassis=1-Slot=2; Driver cannot support the operation.
%May 10 08:22:52:473 2018 SWITCH PBR/5/PBR_DRIVER_NOT_SUPPORT:
-Chassis=1-Slot=3; Driver cannot support the operation.
%May 10 08:22:52:475 2018 SWITCH PBR/5/PBR_DRIVER_NOT_SUPPORT:
-Chassis=1-Slot=4; Driver cannot support the operation.
%May 10 08:22:52:480 2018 SWITCH PBR/5/PBR_DRIVER_NOT_SUPPORT:
-Chassis=2-Slot=1; Driver cannot support the operation.
%May 10 08:22:52:484 2018 SWITCH PBR/5/PBR_DRIVER_NOT_SUPPORT: Driver cannot support the operation.
%May 10 08:22:52:490 2018 SWITCH PBR/5/PBR_DRIVER_NOT_SUPPORT:
-Chassis=2-Slot=2; Driver cannot support the operation.
%May 10 08:22:52:490 2018 SWITCH PBR/5/PBR_DRIVER_NOT_SUPPORT:
-Chassis=2-Slot=3; Driver cannot support the operation.
%May 10 08:22:52:490 2018 SWITCH PBR/5/PBR_DRIVER_NOT_SUPPORT:
-Chassis=2-Slot=4; Driver cannot support the operation.
查看配置:
acl number 3111
rule 0 permit tcp source 192.168.176.1 0 source-port eq telnet
#
policy-based-route testPT permit node 5
if-match acl 3111
apply ip-address next-hop 192.168.183.6
acl的rule规则中没有携带vpn参数,不涉及底层硬件不支持的情况。
查看设备单板类型:
1 0 LSQ1SRPB Slave 0 S7500E-6708P09 None
1 1 LSQ1SRPB Slave 0 S7500E-6708P09 None
1 2 LSQ1GT24SC Normal 0 S7500E-6708P09 None
1 3 LSQ1TGS8SC Normal 0 S7500E-6708P09 None
1 4 LSU3WCMD Normal 0 S7500E-6708P09 None
手册注明SA类单板不支持策略路由,以上单板均支持策略路由下发。
查看设备当前配置,发现如下配置:
irf-pbr disable
查看命令手册:
irf-pbr disable命令用来在四台S7506E/S7506E-V设备组成的IRF中增强业务板的可用性。irf-pbr enable命令用来恢复缺省情况。
缺省情况下,在四台S7506E/S7506E-V设备组成的IRF中,成员设备4的槽位7不可用。
在配置irf-pbr disable命令后,成员设备4的最后一个槽位上可以使用部分型号的业务板(可用业务板型号的信息请参见“IRF配置指导”),同时在IRF中将不能再配置PBR方式的策略路由功能。
现场两台设备堆叠,不需要配置irf-pbr disable命令,删除后,策略路由可以正常下发。
该案例暂时没有网友评论
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作