知

无线控制器V5升级V7典型案例

2015-06-11 发表

0关注
0收藏 3514浏览

陈铮

陈铮八段

粉丝：28人关注：15人

无线控制器ComwareV5版本升级V7

不涉及

将Comware V5上当前运行的配置保存至设备存储。

save

The current configuration will be written to the device. Are you sure? [Y/N]:y

Please input the file name(*.cfg)[cfa0:/startup.cfg]

(To leave the existing filename unchanged, press the enter key):

cfa0:/startup.cfg exists, overwrite? [Y/N]:y

Validating file. Please wait...

Saved the current configuration to mainboard device successfully.

将配置文件备份到PC（IP地址：192.168.100.14）上。注意V5升级V7配置需要参考配置和命令手册先翻译。

tftp 192.168.100.14 put startup.cfg

File will be transferred in binary mode

Sending file to remote TFTP server. Please wait... \

TFTP: 1914 bytes sent in 0 second(s).

File uploaded successfully.

重启设备，当出现“Press Ctrl+B to enter extended boot menu...”时，键入，进入Comware V5 BootWare菜单。

System is starting...

Press Ctrl+D to access BASIC-BOOTWARE MENU

Booting Normal Extend BootWare..

The Extend BootWare is self-decompressing........................

Done!

****************************************************************************

* *

* H3C WCMD BootWare, Version 2.04 *

* *

****************************************************************************

Compiled Date : Nov 19 2014

CPU Type : XLR732

CPU L1 Cache : 32KB

CPU Clock Speed : 950MHz

Memory Type : DDR2 SDRAM

Memory Size : 2048MB

Memory Speed : 533MHz

BootWare Size : 512KB

Flash Size : 4MB

cfa0 Size : 1047MB

CPLD Version : 005

PCB Version : Ver.B

BootWare Validating...

Press Ctrl+B to enter extended boot menu...

BootWare password: Not required. Please press Enter to continue.

Password recovery capability is enabled.

Note: The current operating device is cfa0

Enter < Storage Device Operation > to select device.

======================================================

|<1> Boot System |

|<2> Enter Serial SubMenu |

|<3> Enter Ethernet SubMenu |

|<4> File Control |

|<5> Restore to Factory Default Configuration |

|<6> Skip Current System Configuration |

|<7> BootWare Operation Menu |

|<8> Clear Super Password |

|<9> Storage Device Operation |

|<0> Reboot |

============================================================================

Ctrl+Z: Access EXTEND-ASSISTANT MENU

Ctrl+F: Format File System

Enter your choice(0-9):

按Ctrl+F完成存储介质的格式化

Warning:All files on cfa0 will be lost! Are you sure to format? [Y/N]Y.....

.........................................................

Format success.

完成存储介质的格式化之后，重新进入Bootware主菜单：

======================================================

|<1> Boot System |

|<2> Enter Serial SubMenu |

|<3> Enter Ethernet SubMenu |

|<4> File Control |

|<5> Restore to Factory Default Configuration |

|<6> Skip Current System Configuration |

|<7> BootWare Operation Menu |

|<8> Clear Super Password |

|<9> Storage Device Operation |

|<0> Reboot |

============================================================================

Ctrl+Z: Access EXTEND-ASSISTANT MENU

Ctrl+F: Format File System

Enter your choice(0-9): 3

在BootWare主菜单下选择<3>可以进入以太网操作子菜单：

====================================================

|Note:the operating device is cfa0 |

|<1> Download Application Program To SDRAM And Run |

|<2> Update Main Application File |

|<3> Update Backup Application File |

|<4> Update Secure Application File |

|<5> Modify Ethernet Parameter |

|<0> Exit To Main Menu |

| |

============================================================================

Enter your choice(0-4): 5

在以太网操作子菜单选择<5>，进入以太网口配置菜单：

====================================================

|Note: '.' = Clear field. |

| '-' = Go to previous field. |

| Ctrl+D = Quit. |

============================================================================

Protocol (FTP or TFTP) :tftp

Load File Name :host

:UWWM20-BootWareUpdate-V001.bin

Target File Name :target

:UWWM20-BootWareUpdate-V001.bin

Server IP Address :192.168.100.14

Local IP Address :192.168.100.122

Gateway IP Address :0.0.0.0 255.255.255.0

选择<1>，下载Comware V7版本BootWare文件。

====================================================

|Note:the operating device is cfa0 |

|<1> Download Application Program To SDRAM And Run |

|<2> Update Main Application File |

|<3> Update Backup Application File |

|<4> Update Secure Application File |

|<5> Modify Ethernet Parameter |

|<0> Exit To Main Menu |

| |

============================================================================

Enter your choice(0-4): 1

Loading..........Done!

374784 bytes downloaded!

Extend BootWare Version is not equal,updating? [Y/N]Y

Updating Extend BootWare...Done!

BootWare updated,System is rebooting now.

BootWare版本更新后将自动重启。

设备重启后直接进入Comware V7 BootWare主菜单。

System is starting...

Press Ctrl+D to access BASIC-BOOTWARE MENU...

Booting Normal Extended BootWare

The Extended BootWare is self-decompressing.........................Done.

****************************************************************************

* *

* H3C UWWM20 BootWare, Version 3.03 *

* *

****************************************************************************

Compiled Date : Nov 25 2014

CPU Type : XLR732

CPU L1 Cache : 32KB

CPU Clock Speed : 950MHz

Memory Type : DDR2 SDRAM

Memory Size : 2048MB

Memory Speed : 533MHz

BootWare Size : 512KB

Flash Size : 4MB

cfa0 Size : 999MB

CPLD Version : 005

PCB Version : Ver.B

Use default net params.

BootWare Validating...

Backup Basic BootWare not exist

Begin to Update the Backup Basic BootWare.......Done.

Normal Extended BootWare Version is newer than Backup Extended BootWare!

Begin to Update the Backup Extended BootWare.........Done.

Image program does not exist.

Password recovery capability is enabled.

Note: The current operating device is cfa0

Enter < Storage Device Operation > to select device.

====================================================

|<1> Boot System |

|<2> Enter Serial SubMenu |

|<3> Enter Ethernet SubMenu |

|<4> File Control |

|<5> Restore to Factory Default Configuration |

|<6> Skip Current System Configuration |

|<7> BootWare Operation Menu |

|<8> Skip Authentication for Console Login |

|<9> Storage Device Operation |

|<0> Reboot |

============================================================================

Ctrl+Z: Access EXTENDED ASSISTANT MENU

Ctrl+F: Format File System

Enter your choice(0-9): 3

在BootWare主菜单下键入<3>可以进入以太网口子菜单，然后键入<5>就可以进入以太网口配置菜单：

====================================================

|Note:the operating device is cfa0 |

|<1> Download Image Program To SDRAM And Run |

|<2> Update Main Image File |

|<3> Update Backup Image File |

|<4> Download Files(*.*) |

|<5> Modify Ethernet Parameter |

|<0> Exit To Main Menu |

| |

============================================================================

Enter your choice(0-5): 5

====================================================

|Note: '.' = Clear field. |

| '-' = Go to previous field. |

| Ctrl+D = Quit. |

============================================================================

Protocol (FTP or TFTP) :tftp

Load File Name :host

:UWWM20.ipe

Target File Name :target

:UWWM20.ipe

Server IP Address :192.168.100.14

Local IP Address :192.168.100.122

Subnet Mask :0.0.0.0 255.255.255.0

Gateway IP Address :0.0.0.0

键入<2>，下载Comware V7启动文件：

====================================================

|Note:the operating device is cfa0 |

|<1> Download Image Program To SDRAM And Run |

|<2> Update Main Image File |

|<3> Update Backup Image File |

|<4> Download Files(*.*) |

|<5> Modify Ethernet Parameter |

|<0> Exit To Main Menu |

| |

============================================================================

Enter your choice(0-5): 2

Loading.....................................................................

............................................................................

.............................Done.

90542080 bytes downloaded!

Image file UWWM20-cmw710-boot-a5201p03.bin is self-decompressing...

Saving file cfa0:/UWWM20-cmw710-boot-a5201p03.bin ..........................

............................................................................

....................Done.

Image file UWWM20-cmw710-system-a5201p03.bin is self-decompressing...

Saving file cfa0:/UWWM20-cmw710-system-a5201p03.bin ........................

............................................................................

.......................................................................Done.

====================================================

|Note:the operating device is cfa0 |

|<1> Download Image Program To SDRAM And Run |

|<2> Update Main Image File |

|<3> Update Backup Image File |

|<4> Download Files(*.*) |

|<5> Modify Ethernet Parameter |

|<0> Exit To Main Menu |

| |

============================================================================

Enter your choice(0-5): 0

选择<0>，返回BootWare主菜单。选择<1>，引导系统，完成升级。

====================================================

|<1> Boot System |

|<2> Enter Serial SubMenu |

|<3> Enter Ethernet SubMenu |

|<4> File Control |

|<5> Restore to Factory Default Configuration |

|<6> Skip Current System Configuration |

|<7> BootWare Operation Menu |

|<8> Clear Super Password |

|<9> Storage Device Operation |

|<0> Reboot |

============================================================================

Ctrl+Z: Access EXTENDED ASSISTANT MENU

Ctrl+F: Format File System

Enter your choice(0-9): 1

Loading the main image files...

Loading file cfa0:/UWWM20-cmw710-system-a5201p03.bin........................

............................................................................

..............................Done.

Loading file cfa0:/UWWM20-cmw710-boot-a5201p03.bin..........................

............................................................................

............................................................Done.

Image file cfa0:/UWWM20-cmw710-boot-a5201p03.bin is self-decompressing......

............................................................................

........................................................................Done.

System image is starting...

Cryptographic Algorithms Known-Answer Tests are running ...

CPU 0 of slot 1 in chassis 0:

Starting Known-Answer tests in the user space.

Known-answer test for SHA1 passed.

Known-answer test for SHA224 passed.

Known-answer test for SHA256 passed.

Known-answer test for SHA384 passed.

Known-answer test for SHA512 passed.

Known-answer test for HMAC-SHA1 passed.

Known-answer test for HMAC-SHA224 passed.

Known-answer test for HMAC-SHA256 passed.

Known-answer test for HMAC-SHA384 passed.

Known-answer test for HMAC-SHA512 passed.

Known-answer test for AES passed.

Known-answer test for RSA(signature/verification) passed.

Known-answer test for RSA(encrypt/decrypt) passed.

Known-answer test for DSA(signature/verification) passed.

Known-answer test for random number generator passed.

Known-Answer tests in the user space passed.

Starting Known-Answer tests in the kernel.

Known-answer test for SHA1 passed.

Known-answer test for HMAC-SHA1 passed.

Known-answer test for AES passed.

Known-answer test for random number generator passed.

Known-Answer tests in the kernel passed.

Cryptographic Algorithms Known-Answer Tests passed.

Startup configuration file does not exist.

Performing automatic configuration... Press CTRL_C or CTRL_D to break.

Automatic configuration attempt: 1.

Interface used: M-GigabitEthernet0/0/0.

Enable DHCP client on M-GigabitEthernet0/0/0.

Automatic configuration is aborted.

Line con0 is available.

Press ENTER to get started.

设备启动后，使display version命令查看设备版本，显示如下类似信息表示升级成功：

display version

H3C Comware Software,

UWWM20 uptime is 0 weeks, 0 days, 0 hours, 1 minutes

Last reboot reason : User soft reboot

Boot image: cfa0:/UWWM20-cmw710-boot-a5201p03.bin

Boot image version: 7.1.061,

Compiled Nov 26 2014 09:38:00

System image: cfa0:/UWWM20-cmw710-system-a5201p03.bin

System image version: 7.1.061,

Compiled Nov 26 2014 09:38:00

Solt 1

with 1 RMI XLR732 950MHz Processor

2048M bytes DDR2

8M bytes NorFlash Memory

999M bytes CFCard Memory

Hardware Version is Ver.b

FPGA Hardware Version is Ver.a

CPLD Version is 005

FPGA Logic Version is 319

Basic Bootrom Version is 3.03

Extend Bootrom Version is 3.03

[Subslot 0]LSU3WCMD0 Hardware Version is Ver.b

Comware V5的软件包只有一个“.bin”文件，但是Comware V7的软件包包括两个“.bin”文件和一个“.ipe”文件：

· Boot程序（.bin文件）：包含了Linux操作系统的内核，可以提供进程管理、内存管理、文件系统管理和应急shell。格式为“XXXX-cmw710-boot-XXXXX.bin”

· System程序（.bin文件）：包含了设备操作和网络业务相关的模块，包括设备管理、接口管理、配置管理和无线配置。格式为“XXXX-cmw710-system-XXXXX.bin”

· IPE文件：Comware V7的软件包在实际发布的时候，会把boot程序和system程序文件打包成一个IPE文件。格式为“XXXXX.ipe”

升级流程图如下：

注意V5升级V7配置需要参考配置和命令手册先翻译。

该案例对您是否有帮助：

您的评价：1

若您有关于案例的建议，请反馈：

作者在2019-06-12对此案例进行了修订

1 个评论

zhiliao_t8nSV

zhiliao_t8nSV 二段

粉丝：0人关注：0人

这个bootware升级包从哪里下载的

编辑评论

侵犯我的权益 >

对根叔知了社区有害的内容 >

辱骂、歧视、挑衅等（不友善）

侵犯我的权益

泄露了我的隐私 >

侵犯了我企业的权益 >

抄袭了我的内容 >

诽谤我 >

辱骂、歧视、挑衅等（不友善）

骚扰我

泄露了我的隐私

您好，当您发现根叔知了上有泄漏您隐私的内容时，您可以向根叔知了进行举报。请您把以下内容通过邮件发送到pub.zhiliao@h3c.com 邮箱，我们会尽快处理。

1. 您认为哪些内容泄露了您的隐私？（请在邮件中列出您举报的内容、链接地址，并给出简短的说明）
2. 您是谁？（身份证明材料，可以是身份证或护照等证件）

侵犯了我企业的权益

您好，当您发现根叔知了上有关于您企业的造谣与诽谤、商业侵权等内容时，您可以向根叔知了进行举报。请您把以下内容通过邮件发送到 pub.zhiliao@h3c.com 邮箱，我们会在审核后尽快给您答复。

1. 您举报的内容是什么？（请在邮件中列出您举报的内容和链接地址）
2. 您是谁？（身份证明材料，可以是身份证或护照等证件）
3. 是哪家企业？（营业执照，单位登记证明等证件）
4. 您与该企业的关系是？（您是企业法人或被授权人，需提供企业委托授权书）

我们认为知名企业应该坦然接受公众讨论，对于答案中不准确的部分，我们欢迎您以正式或非正式身份在根叔知了上进行澄清。

抄袭了我的内容

原文链接或出处

诽谤我

您好，当您发现根叔知了上有诽谤您的内容时，您可以向根叔知了进行举报。请您把以下内容通过邮件发送到pub.zhiliao@h3c.com 邮箱，我们会尽快处理。

1. 您举报的内容以及侵犯了您什么权益？（请在邮件中列出您举报的内容、链接地址，并给出简短的说明）
2. 您是谁？（身份证明材料，可以是身份证或护照等证件）

我们认为知名企业应该坦然接受公众讨论，对于答案中不准确的部分，我们欢迎您以正式或非正式身份在根叔知了上进行澄清。

对根叔知了社区有害的内容

垃圾广告信息

色情、暴力、血腥等违反法律法规的内容

政治敏感

不规范转载 >

辱骂、歧视、挑衅等（不友善）

骚扰我

诱导投票

不规范转载

举报说明

✖

案例意见反馈

➤

网站相关: 关于我们; 服务条款; 帮助中心; 经验与权限; 积分规则

联系我们: 联系我们; 建议反馈

常用链接: 知了APP下载; 标杆的神器下载

关注我们: H3C官网; 新华三服务公众号; 安仔远程运维服务; 新华三商城

内容许可: 除特别说明外，用户内容均可采用知识共享署名-相同方式共享3.0中国大陆许可协议进行许可

本图标版权归新华三集团所有，仅限本社区使用，切勿用做商业目的，违者必究

浙ICP备09064986号-1 浙公网安备 33010802004416号

✖

亲~登录后才可以操作哦!

确定

✖

亲~检测到您登陆的账号未在http://hclhub.h3c.com进行注册

注册后可访问此模块

跳转hclhub

✖

你的邮箱还未认证，请认证邮箱或绑定手机后进行当前操作

✖

产品线		搜索取消
案例类型
发布者
是否解决
是否官方
时间
搜索引擎
匹配模式	默认策略匹配全词匹配整句

无线控制器V5升级V7典型案例

编辑评论

提出建议