3 配置步骤

3.1  路由器A配置

3.1.1  配置路由器A下联防火墙接口

system

[H3C]interface GigabitEthernet 1/0/1

[H3C-GigabitEthernet1/0/1] ip address 1.1.1.1 24

[H3C-GigabitEthernet1/0/1]quit

[H3C]ospf 1

[H3C-ospf-1]area 0

[H3C-ospf-1-area-0.0.0.0]network 1.1.1.1 0.0.0.0

路由器B、C、D配置相同不再赘述

3.2  防火墙配置

3.2.1  FWA与FWB建立堆叠

具体配置可参考防火墙虚拟化配置举例，本章不做介绍。

3.2.2  配置track联动上下行接口的物理状态

配置track检测上下行端口的物理状态

[H3C] track 1 interface gigabitethernet 1/0/1 physical

[H3C-track-1] quit

[H3C] track 2 interface gigabitethernet 1/0/2 physical

[H3C-track-2] quit

[H3C] track 3 interface gigabitethernet 2/0/1 physical

[H3C-track-3] quit

[H3C] track 4 interface gigabitethernet 2/0/2 physical

[H3C-track-4] quit

3.2.3  配置冗余组关联冗余接口

1. 创建节点1与防火墙A所有接口绑定

[H3C] redundancy group aaa

[H3C-redundancy-group-aaa] node 1

[H3C-redundancy-group-aaa-node1] bind slot 1

[H3C-redundancy-group-aaa-node1] priority 100

[H3C-redundancy-group-aaa-node1] node-member interface gigabitethernet 1/0/1

[H3C-redundancy-group-aaa-node1] node-member interface gigabitethernet 1/0/2

[H3C-redundancy-group-aaa-node1] track 1 interface gigabitethernet 1/0/1

[H3C-redundancy-group-aaa-node1] track 2 interface gigabitethernet 1/0/2

[H3C-redundancy-group-aaa-node1] quit

2. 创建节点2与防火墙B所有接口绑定

[H3C-redundancy-group-aaa] node 2

[H3C-redundancy-group-aaa-node2] bind slot 2

[H3C-redundancy-group-aaa-node2] priority 50

[H3C-redundancy-group-aaa-node2] node-member interface gigabitethernet 2/0/1

[H3C-redundancy-group-aaa-node2] node-member interface gigabitethernet 2/0/2

[H3C-redundancy-group-aaa-node2] track 3 interface gigabitethernet 2/0/1

[H3C-redundancy-group-aaa-node2] track 4 interface gigabitethernet 2/0/2

[H3C-redundancy-group-aaa-node2] quit

3.2.4  开启会话热备

[H3C] session synchronization enable

3.2.5  安全策略配置

1. 将接口加入安全域

将1/0/1与2/0/1加入Untrust区域

[H3C]security-zone name Untrust

[H3C-security-zone-Untrust]import interface GigabitEthernet 1/0/1

[H3C-security-zone-Untrust]import interface GigabitEthernet 2/0/1

将1/0/2与2/0/2加入trust区域

[H3C]security-zone name trust

[H3C-security-zone-trust]import interface GigabitEthernet 1/0/2

[H3C-security-zone-trust]import interface GigabitEthernet 2/0/2

[H3C-security-zone-trust]quit

防火墙目前版本存在两套安全策略，请在放通安全策略前确认设备运行那种类型的安全策略？以下配置任选其一。

2. 通过命令“display cu | in security-policy”如果查到命令行存在“security-policy disable”或者没有查到任何信息，则使用下面策略配置。

[H3C]display cu | in security-policy

 security-policy disable

#创建对象策略pass。

[H3C]object-policy ip pass

[H3C-object-policy-ip-pass] rule 0 pass

[H3C-object-policy-ip-pass]quit

#创建Trust到Untrust域的域间策略调用pass策略。

[H3C]zone-pair security source Trust destination local

[H3C-zone-pair-security-Trust- local]object-policy apply ip pass

[H3C-zone-pair-security-Trust- local]quit

[H3C]zone-pair security source local destination Trust

[H3C-zone-pair-security-local -trust]object-policy apply ip pass

[H3C-zone-pair-security-local -trust]quit

[H3C]zone-pair security source Untrust destination local

[H3C-zone-pair-security-Untrust- local]object-policy apply ip pass

[H3C-zone-pair-security-Untrust- local]quit

[H3C]zone-pair security source local destination Untrust

[H3C-zone-pair-security-local -Untrust]object-policy apply ip pass

[H3C-zone-pair-security-local -Untrust]quit

[H3C]zone-pair security source Trust destination Untrust

[H3C-zone-pair-security-Trust -Untrust]object-policy apply ip pass

[H3C-zone-pair-security-Trust -Untrust]quit

3. 通过命令“display cu | in security-policy”如果查到命令行存在“security-policy ip”并且没有查到“security-policy disable”，则使用下面策略配置。

[H3C]display cu | in security-policy

security-policy ip

创建安全策略并放通local到trust和trust到local的安全策略。

[H3C]security-policy ip

[H3C-security-policy-ip]rule 10 name test

[H3C-security-policy-ip-10-test]action pass

[H3C-security-policy-ip-10-test]source-zone local

[H3C-security-policy-ip-10-test]source-zone Trust

[H3C-security-policy-ip-10-test]source-zone Untrust

[H3C-security-policy-ip-10-test]destination-zone local

[H3C-security-policy-ip-10-test]destination-zone Trust

[H3C-security-policy-ip-10-test]destination-zone Untrust

[H3C-security-policy-ip-10-test]quit

4 检验配置结果

4.1.1  正常时查看冗余组状态

节点1为主用状态，节点二为备用状态。

[H3C-redundancy-group-aaa] display redundancy group aaa

Redundancy group aaa (ID 1):

  Node ID      Slot       Priority   Status        Track weight

  1            Slot1      100        Primary       255

  2            Slot2      50         Secondary     255

Preempt delay time remained     : 0    min

Preempt delay timer setting     : 1    min

Remaining hold-down time        : 0    sec

Hold-down timer setting         : 1    sec

Manual switchover request       : No

Member interfaces:

Node 1:

  Node member     Physical status

      GE1/0/1   UP

      GE1/0/2   UP

  Track info:

    Track    Status       Reduced weight     Interface

    1        Positive     255                GE1/0/1

    2        Positive     255                GE1/0/2

Node 2:

  Node member     Physical status

      GE2/0/1   UP

      GE2/0/2   UP

  Track info:

    Track    Status       Reduced weight     Interface

    3        Positive       255              GE2/0/1

    4        Positive       255              GE2/0/2

4.1.2  手动关闭1/0/2接口后时查看冗余组状态

查看到主备状态已经发生了变化，并且1/0/1与1/0/2的物理状态全部置为down。

[H3C] display redundancy group aaa

Redundancy group aaa (ID 1):

  Node ID      Slot       Priority   Status        Track weight

  1            Slot1      100        Secondary     -255

  2            Slot2      50         Primary       255

Preempt delay time remained     : 0    min

Preempt delay timer setting     : 1    min

Remaining hold-down time        : 0    sec

Hold-down timer setting         : 1    sec

Manual switchover request       : No

Member interfaces:

Node 1:

  Node member     Physical status

      GE1/0/1       DOWN(redundancy down)

      GE1/0/2       DOWN

  Track info:

    Track    Status       Reduced weight     Interface

    1         Negative     255                GE1/0/1

    2         Negative     255                GE1/0/2 (Fault)

Node 2:

  Node member     Physical status

      GE2/0/1   UP

      GE2/0/2   UP

  Track info:

    Track    Status       Reduced weight     Interface

    3         Positive       255              GE2/0/1

    4         Positive       255              GE2/0/2

4.1.3  注意事项

1、配置冗余组后需要加入冗余接口的物理口全部连接，否则会造成冗余组异常。