MSR路由器MPLS L3VPN HubSpoke功能配置

MSR路由器

MPLS L3VPN HubSpoke功能的配置

 

关键词：MSR;MPLS;BGP;L3VPN;Hub Spoke;团体属性

 

一、组网需求：

SPOKEA和SPOKEB是vpna的2个分布站点接入PE，总部站点用CEA表示，CEA的接入PE是HubA，要求SPOKEA和SPOKEB之间的VPN流量都需要从总部站点转发。

设备清单：MSR路由器4台

二、组网图：

三、配置步骤：

适用设备和版本：MSR、Version 5.20, Beta 1105后所有版本。

SpokeA配置

#

router id 2.2.2.2

#

ip vpn-instance vpna

route-distinguisher 2:1

vpn-target 2:1 export-extcommunity    //配置vpna的出团体属性

vpn-target 1:1 import-extcommunity    //配置vpna的入团体属性

#

mpls lsr-id 2.2.2.2

#

mpls

ttl propagate vpn                     //使能vpn的ttl复制，用于tracert

#

mpls ldp

#

interface Ethernet0/0

port link-mode route

ip address 1.2.3.2 255.255.255.0

mpls

mpls ldp

#

interface Ethernet0/1

 port link-mode route

ip binding vpn-instance vpna           //绑定vpn实例vpna

ip address 172.32.0.1 255.255.255.0

#

interface LoopBack0

ip address 2.2.2.2 255.255.255.255

#

bgp 1

undo synchronization

peer 1.1.1.1 as-number 1

peer 1.1.1.1 connect-interface LoopBack0

#

ipv4-family vpnv4

peer 1.1.1.1 enable

#

ipv4-family vpn-instance vpna

import-route direct

#

ospf 1

area 0.0.0.0

network 2.2.2.2 0.0.0.0

network 1.2.3.0 0.0.0.255

#

SpokeB配置

#

router id 3.3.3.3

#

ip vpn-instance vpna

route-distinguisher 3:1

vpn-target 3:1 export-extcommunity    //配置vpna的出团体属性

vpn-target 1:1 import-extcommunity    //配置vpna的入团体属性

#

mpls lsr-id 3.3.3.3

#

mpls

ttl propagate vpn                     //使能vpn的ttl复制，用于tracert

#

mpls ldp

#

interface Ethernet0/0

port link-mode route

ip address 1.2.3.3 255.255.255.0

mpls

mpls ldp

#

interface Ethernet0/1

port link-mode route

ip binding vpn-instance vpna           //绑定vpn实例vpna

ip address 172.32.1.1 255.255.255.0

#

interface LoopBack0

ip address 3.3.3.3 255.255.255.255

#

bgp 1

undo synchronization

peer 1.1.1.1 as-number 1

peer 1.1.1.1 connect-interface LoopBack0

#

ipv4-family vpnv4

peer 1.1.1.1 enable

#

ipv4-family vpn-instance vpna

network 172.32.1.0 255.255.255.0

#

ospf 1

area 0.0.0.0

network 3.3.3.3 0.0.0.0

network 1.2.3.0 0.0.0.255

#

Hub配置

#

router id 1.1.1.1

#

ip vpn-instance vpnin

route-distinguisher 1:2

vpn-target 2:1 3:1 import-extcommunity   //入团体属性

#

ip vpn-instance vpnout

route-distinguisher 1:1

vpn-target 1:1 export-extcommunity       //出团体属性

#

mpls lsr-id 1.1.1.1

#

mpls

ttl propagate vpn                        //使能vpn的ttl复制，用于tracert

#

mpls ldp

#

interface Ethernet0/0

port link-mode route

ip address 1.2.3.1 255.255.255.0

mpls

mpls ldp

#

interface Ethernet0/1

 port link-mode route

ip binding vpn-instance vpnout            //绑定vpn实例vpnout

ip address 192.168.1.1 255.255.255.0

#

interface Ethernet1/0

port link-mode route

ip binding vpn-instance vpnin             //绑定vpn实例vpnin

ip address 192.168.0.1 255.255.255.0

#

interface LoopBack0

ip address 1.1.1.1 255.255.255.255

#

bgp 1

undo synchronization

group 1 internal

peer 1 connect-interface LoopBack0

peer 3.3.3.3 group 1

peer 2.2.2.2 group 1

#

ipv4-family vpnv4

peer 1 enable

peer 2.2.2.2 enable

peer 2.2.2.2 group 1

peer 3.3.3.3 enable

peer 3.3.3.3 group 1

#

ipv4-family vpn-instance vpnin            //vpnin的路由和peer配置

peer 192.168.0.2 as-number 2             //与CEA建立EBGP连接

#

ipv4-family vpn-instance vpnout           //vpnout的路由和peer配置

peer 192.168.1.2 as-number 2             //与CEA建立EBGP连接

network 192.168.1.0

peer 192.168.1.2 allow-as-loop           //必配，使能接受路由环路

#

ospf 1

area 0.0.0.0

network 1.1.1.1 0.0.0.0

network 1.2.3.0 0.0.0.255

#

CE配置

#

interface Ethernet0/1

 port link-mode route

ip address 192.168.1.2 255.255.255.0

#

interface Ethernet1/0

port link-mode route

ip address 192.168.0.2 255.255.255.0

#

bgp 2

network 192.168.0.0

undo synchronization

peer 192.168.1.1 as-number 1

peer 192.168.0.1 as-number 1

group 1 external

peer 192.168.1.1 group 1

peer 192.168.0.1 group 1

#

四、配置关键点：

1.      掌握VPN路由的流向；

2.      注意Spoke上vpn-target的配置；

3.      Hub上配置2个vpn实例及其vpn-target配置；

4.      Hub的BGP配置，需要与CE建立2条EBGP连接，都配置在vpn实例视图下；

5.      Hub上vpnout实例要配置接受环路路由。