SecBlade防火墙单板作为LNS接受SecPoint L2TP 拨入的配置

SecBlade防火墙单板作为LNS接受SecPoint L2TP

拨入的配置

 

一、  组网需求：

SecBlade防火墙单板作为LNS，接受SecPoint L2TP拨入。

二、  组网图：

       

要做LNS，SecBlade板只能工作在路由模式，S8505创建三层接口int Vlan-interface 40，作为与SecBlade的内部接口，内网PCA的网关在S8500上。PCB上安装L2TP客户端软件，通过L2TP方式拨入SecBlade，访问内部资源。

 

软件版本如下：

S8505: VRP310-R1271

SecBlade：VRP3.4-ESS1209

SecPoint：5.05

 

三、  配置步骤：

 

本配置适用于S8500VRP3.1-R1271及以后版本，SecBlade VRP3.4-E1209及以后版本，SecPoint3.08及以后版本。

 

1、S8500配置

<S8505>dis cu                                                                  

#                                                                               

 config-version S8500-VRP310-r1271                                             

#                                                                              

 sysname S8505                                                                  

#                                                                              

 super password level 1 cipher O5(YaI!$LR+Q=^Q`MAF4<1!!                        

#                                                                               

 local-server nas-ip 127.0.0.1 key huawei                                      

#                                                                              

 Xbar load-single                                                               

#                                                                              

 router route-limit 128K                                                       

 router VRF-limit 256                                                          

#                                                                               

 secblade aggregation slot 2              //配置内部端口聚合，增大带宽                                       

#                                                                              

radius scheme system                                                           

 server-type huawei                                                            

 primary authentication 127.0.0.1 1645                                         

 primary accounting 127.0.0.1 1646                                             

 user-name-format without-domain                                               

#                                                                              

domain system                                                                   

 vlan-assignment-mode integer                                                  

 access-limit disable                                                          

 state active                                                                   

 idle-cut disable                                                              

 self-service-url disable                                                      

                                                                                

 domain default enable system                                                  

#                                                                              

vlan 1                                                                          

#                                                                              

vlan 30                   //创建vlan30、vlan40、vlan50、vlan60                                                     

#                                                                              

vlan 40                                                                        

#                                                                               

vlan 50                                                                        

#                                                                              

vlan 60                                                                         

#                                                                              

interface Vlan-interface30               //内网网关                                            

 ip address 30.0.0.254 255.255.255.0                                           

#                                                                              

interface Vlan-interface40                //与SecBlade内部三层接口                                          

 ip address 40.0.0.2 255.255.255.0                                             

#                                                                              

interface Aux0/0/1                                                              

#                                                                              

interface M-Ethernet0/0/0                                                      

#                                                                               

interface Ethernet4/1/1                 //eth4/1/1接内网                                           

 port access vlan 30                                                           

#                                                                              

interface Ethernet4/1/2                //eth4/1/2接外网                                            

 port access vlan 60                                                           

#                                                                              

interface Ethernet4/1/3               //eth4/1/3接DMZ服务器                                           

 port access vlan 50                                                           

#                                                                              

…… ……                                             

                                                      

interface NULL0                                                                

#                                                                              

 ip route-static 0.0.0.0 0.0.0.0 40.0.0.1 preference 60   //通过路由，将来自内网的数据送给Secblade                     

#                                                                              

user-interface con 0                                                           

user-interface aux 0                                                            

user-interface vty 0 4                                                         

#                                                                              

secblade module secblade                                                        

 security-vlan 50 60      //vlan50、60作为security-vlan，将来自外网和DMZ的数据送到SecBlade                                                 

 secblade-interface Vlan-interface40     //vlan40为S8500与SecBlade的内部三层接口                                       

 map to slot 2                       //SecBlade板在2号槽位                                           

#                                                                              

return                                                                         

                                                                                

                                                                      

 

2、SecBlade配置：

<SecBlade_FW>dis cu                                                            

#                                                                               

 sysname SecBlade_FW                                                           

#                                                                              

 l2tp enable                                                                    

#                                                                              

 firewall packet-filter enable                                                 

 firewall packet-filter default permit   //包过滤缺省规则设置为permit                                      

#                                                                              

 firewall statistic system enable                                              

#                                                                               

radius scheme system                                                           

#                                                                              

domain system                 //注意在域下配置地址池，而不是全局下                                                  

 ip pool 1 1.1.1.2 1.1.1.254                                                   

#                                                                              

local-user l2tp                 //创建l2tp用户                                               

 password simple l2tp                                                          

 level 3                                                                       

 service-type ppp                                                               

#                                                                              

acl number 2000                                                                

 rule 0 permit source 40.0.0.0 0.255.255.255                                    

 rule 1 permit source 30.0.0.0 0.255.255.255                                   

#                                                                              

interface Virtual-Template0       //创建L2TP虚模板                                              

 ppp authentication-mode pap                                                   

 ip address 1.1.1.1 255.255.255.0                                              

 remote address pool 1                                                          

#                                                                              

interface Aux0                                                                 

 async mode flow                                                               

#                                                                               

interface Ethernet0/1                                                          

#                                                                              

interface Ethernet0/2                                                           

#                                                                              

interface Ethernet0/3                                                          

#                                                                               

interface GigabitEthernet0/0                                                   

#                                                                              

interface GigabitEthernet0/0.1       //与S8500的内部接口                                           

 ip address 40.0.0.1 255.255.255.0                                             

 vlan-type dot1q vid 40                                                        

#                                                                               

interface GigabitEthernet0/0.2        //外网接口                                           

 ip address 60.0.0.1 255.255.255.0                                             

 vlan-type dot1q vid 60                                                         

 nat outbound 2000                 //做nat                                            

 nat server protocol tcp global 60.0.0.2 ftp inside 50.0.0.50 ftp   //做natserver           

#                                                                               

interface GigabitEthernet0/0.3        //DMZ区域SERVER的网关                                         

 ip address 50.0.0.1 255.255.255.0                                             

 vlan-type dot1q vid 50                                                         

#                                                                              

interface NULL0                                                                

#                                                                               

firewall zone local                                                            

 set priority 100                                                              

#                                                                               

firewall zone trust                  //内网接口加入trust域                                             

 add interface GigabitEthernet0/0.1                                            

 set priority 85                                                                

#                                                                              

firewall zone untrust                                                          

 add interface GigabitEthernet0/0.2                                          

 add interface Virtual-Template0      //注意将虚模板也加入untrust域                                           

 set priority 5                                                                

#                                                                               

firewall zone DMZ                                                                

 add interface GigabitEthernet0/0.3                                            

 set priority 50                                                               

#                                                                               

firewall interzone local trust                                                 

#                                                                              

firewall interzone local untrust                                               

#                                                                              

firewall interzone local DMZ                                                   

#                                                                               

firewall interzone trust untrust                                               

#                                                                              

firewall interzone trust DMZ                                                    

#                                                                              

firewall interzone DMZ untrust                                                 

#                                                                               

l2tp-group 1                       //建立l2tp组                                              

 undo tunnel authentication                                                    

 allow l2tp virtual-template 0                                              

#                                                                              

 ip route-static 0.0.0.0 0.0.0.0 60.0.0.60 preference 60      //到公网的缺省路由                      

 ip route-static 30.0.0.0 255.255.255.0 40.0.0.2 preference 60   //到内网的路由                  

#                                                                              

user-interface con 0                                                           

user-interface aux 0                                                            

 authentication-mode password                                                  

user-interface vty 0 4                                                         

 authentication-mode scheme                                                    

#                                                                              

return                                                                         

<SecBlade_FW>                                                                  

<SecBlade_FW> 

 

                                                                               

3、   SecPoint的配置：

           设置LNS地址：

          

           L2TP相关设置：

           

          因为前面选择的是“连接成功后不允许访问internet”，因此不用设置路由，否则要设置到要访问的内网网段的路由：

          

四、     配置关键点：   

1、SecBlade上要有到内网和外网的路由；S8500上要有到外网的路由，下一跳指向SecBlade。

2、注意将SecBlade子接口加入安全域，虚模板也要加入安全域。

3、注意在domain下配置ip pool，而不是全局下。