使用H3C XE200/2000进行号码路由

使用H3C XE200/2000进行号码路由

 

一 组网需求：

IP电话通过VG2108的FXO接到PBX落地，PSTN侧电话也通过VG2108接入；

IP话机和VG2108都通过XE来定位号码，VG2108的第一和第二个FXO口要与IP电话802、803一一绑定（即：802拨出的电话只从VG2108的第一FXO口出局，pstn拨到第一FXO口的号码时802直接震铃）。

从IP侧拨出电话与普通的外线电话拨号规则相同，直接拨区号＋市话号码或本地市话号码和手机号码，拨打外地手机加0，也支持拨打17909等号码。

二 组网图:

三 配置步骤：

1 配置语音服务器XE2000

# 配置以太网接口

[XE] interface ethernet 0/0

[XE-Ethernet0/0] ip address 1.1.1.1 255.255.255.0

[XE-Ethernet0/0] quit

# 配置网守

[XE] process-server

[XE-ps] ps-config gkserver interface Ethernet 0/0

[XE-ps] heartbeat password xe

[XE-ps] ls-mode 0 local

[XE-ps] start

[XE-ps] gatekeeper

[XE-ps-gk] start

# 配置位置服务器

[XE] location-server

[XE-ls] ls-config interface Ethernet 0/0

[XE-ls] process-server gkserver

[XE-ls-ps-gkserver] heartbeat password xe

# 配置网关设备

[XE-ls] gate-way VG_21-08

[XE-ls-gw- VG_21-08] device-type h323

[XE-ls-gw- VG_21-08] dynamic-ip enable

[XE-ls-gw- VG_21-08] prefix.%

// 为VG_21-08下的所有实体做号码路由，允许所有号码路由到VG_21-08上

[XE-ls-gw- VG_21-08] priority 5 

// 降低该网关的优先级别，让所有号码最后匹配该网关

[XE-ls-gw- VG_21-08] quit

[XE-ls] gate-way gejipphone

// IP电话1，号码802

[XE-ls-gw- gejipphone] device-type h323

[XE-ls-gw- gejipphone] dynamic-ip enable

[XE-ls-gw- gejipphone] quit

[XE-ls] gate-way segipphone

// IP电话2，号码803

[XE-ls-gw- segipphone] device-type h323

[XE-ls-gw- segipphone] dynamic-ip enable

[XE-ls-gw- segipphone] quit

2  配置语音网关VG B

# 配置全局模式下的语音编解码协议

[VGB] voice-setup

[VGB-voice] dial-program

[VGB-voice-dial] entity 8 voip

[VGB-voice-dial-entity8] match-template 8.T

[VGB-voice-dial-entity8] address ras

[VGB-voice-dial-entity8] quit

[VGB-voice-dial] entity 1802 pots

[VGB-voice-dial-entity1802] match-template .T

[VGB-voice-dial-entity1802] caller-permit 802

//只允许主叫号码为802的电话出局到pstn

[VGB-voice-dial-entity1802] send-number all

//将xe送来的所有号码都送给pbx

[VGB-voice-dial-entity1802] quit

[VGB-voice-dial] entity 1803 pots

[VGB-voice-dial-entity1803] match-template .T

[VGB-voice-dial-entity1803] caller-permit 803

//只允许主叫号码为803的电话出局到pastn

[VGB-voice-dial-entity1802] send-number all

//将xe送来的所有号码都送给pbx

[VGB-voice-dial-entity1803] quit

[VGB-voice-dial] gk-client

[VGB-voice-gk] gk-id XE_200 gk-addr 1.1.1.1 1719

[VGB-voice-gk] gk-id XE_200 gk-addr 192.168.16.252

[VGB-voice-gk] gw-address ip 1.1.1.2 

[VGB-voice-gk] gw-id VG_21-08

[VGB-voice-gk] ras-on

[VGB-voice-gk] quit

[VGB-voice] subscriber-line 0

[VGB-voice-line0] area custom

[VGB-voice-line0] private-line 802

[VGB-voice-line0] quit

[VGB-voice] subscriber-line 1

[VGB-voice-line1] area custom

[VGB-voice-line1] private-line 803

四 配置关键点：

XE号码路由的方式只有三种，一种是vg动态号码注册，第二种是xe自己放号，最后一种就是网关下用prefix命令来配置一条静态路由号码。