H3C XE200/2000主叫号码路由的配置方法

H3C XE200/2000主叫号码路由的配置方法

 

一 组网需求：

语音服务器XE0域内网关GW0下用户1001可以通过IP呼叫域外用户，同时为其配置主叫号码路由，以实现当IP线路不通时，用户1001可以通过中继网关GW1，直接拨出中继线，呼叫域外用户。

二 组网图:

三 配置步骤：

1 配置Gateway GW0

# 配置以太网接口

[GW0] interface ethernet 0

[GW0-Ethernet0] ip address 192.168.0.10 255.255.255.0

[GW0-Ethernet0] quit

# 配置语音实体

[GW0] voice-setup

[GW0-voice] dial-program

[GW0-voice-dial] entity 1000 voip

[GW0-voice-dial-entity1000] address ras

[GW0-voice-dial-entity1000] match-template .T

[GW0-voice-dial-entity1000] outband h225

[GW0-voice-dial-entity1000] fast-connect

[GW0-voice-dial-entity1000] quit

[GW0-voice-dial] entity 1001 pots

[GW0-voice-dial-entity1001] line 0

[GW0-voice-dial-entity1001] match-template #0

[GW0-voice-dial-entity1001] outband h225

[GW0-voice-dial-entity1001] quit

[GW0-voice-dial] quit

# 配置GK-Client

[GW0-voice] gk-client

[GW0-voice-gk] gw-id GW0

[GW0-voice-gk] gw-address ethernet 0

[GW0-voice-gk] gk-id ps1 gk-addr 192.168.0.1

[GW0-voice-gk] ras on

2 配置网关GW1

# 配置以太网接口

[GW1] interface ethernet 0

[GW1-Ethernet0] ip address 192.168.0.11 255.255.255.0

[GW1-Ethernet0] quit

# 配置语音实体

[GW1] voice-setup

[GW1-voice] dial-program

[GW1-voice-dial] entity 2000 voip

[GW1-voice-dial-entity2000] address ras

[GW1-voice-dial-entity2000] match-template .T

[GW1-voice-dial-entity1000] outband h225

[GW1-voice-dial-entity1000] fast-connect

[GW1-voice-dial-entity2000] quit

[GW1-voice-dial] entity 2001 pots

[GW1-voice-dial-entity2001] line 0

[GW1-voice-dial-entity2001] match-template .T

[GW1-voice-dial-entity2001] send-number all

[GW1-voice-dial-entity2001] quit

# 配置中继线

[GW1-voice] subscriber-line 0

[GW1-voice-line0] private-line 1001

[GW1-voice-line0] return

# 配置GK-Client

[GW1] voice-setup

[GW1-voice] gk-client

[GW1-voice-gk] gw-id GW1

[GW1-voice-gk] gw-address ethernet 0

[GW1-voice-gk] gk-id ps1 gk-addr 192.168.0.1

[GW1-voice-gk] ras on

3        配置H.323网守XE0

# 配置以太网接口

[XE0] interface ethernet 0/0

[XE0-Ethernet0/0] ip address 192.168.0.1 255.255.255.0

[XE0-Ethernet0/0] quit

# 配置处理服务器

[XE0] process-server

[XE0-ps] ps-config ps1 interface Ethernet 0/0

[XE0-ps] heartbeat password 123456

[XE0-ps] ls-mode 0 local

[XE0-ps] start

[XE0-ps] gatekeeper

[XE0-ps-gk] start

[XE0-ps-gk] quit

[XE0-ps] quit

# 配置位置服务器

[XE0] location-server

[XE0-ls] heartbeat password 123456

[XE0-ls] start

# 配置IP出局

[XE0-ls] office-group og1

[XE0-ls-og-og1] office ps1

[XE0-ls-og-og1 ps1] ip-address 192.168.1.1

[XE0-ls-og-og1 ps1] port 1719

[XE0-ls-og-og1 ps1] device-type h323-gk

[XE0-ls-og-og1 ps1] device-status normal

[XE0-ls-og-og1 ps1] quit

[XE0-ls-og-og1] prefix .%

[XE0-ls-og-og1 .%] quit

[XE0-ls-og-og1]quit

# 配置中继网关出局

[XE0-ls] gateway GW1

[XE0-ls-gw-GW1] dynamic-ip enable

[XE0-ls-gw-GW1] device-type h323

[XE0-ls-gw-GW1] device-status normal

[XE0-ls-gw-GW1] prefix .%

[XE0-ls-gw-GW1 .%] otapc relay

[XE0-ls-gw-GW1 .%] quit

[XE0-ls-gw-GW1] quit

#配置主叫网关

[XE0-ls] gateway GW0

[XE0-ls-gw-GW0] dynamic-ip enable

[XE0-ls-gw-GW0] device-type h323

[XE0-ls-gw-GW0] device-status normal

[XE0-ls-gw-GW0] subscriber 0 1001

[XE0-ls-gw-GW0 #0 1001] quit

# 配置主叫号码路由

[XE0-ls-gw-GW0] caller-route 0 caller 1001 callee .% gateway GW1

四 配置关键点：

当需要启用主叫号码路由特性功能时，需要在主叫设备下配置主叫号码路由，指定其被叫出局设备，同时，在被叫出局设备下配置prefix，并设置其otapc属性为relay。