WA1208E的WDS接口下Trunk功能的配置

WA1208E的WDS接口下Trunk功能的配置

适用WA1208E版本：E1101版本

适用WA1208E型号：WA1208E-G / WA1208E-DG / WA1208E-AG /  WA1208E-AGP

一、组网需求

两台WA1208E、两台交换机

二、组网图

1、WA1208E A的VLAN 1接口IP地址为“192.168.0.10”，WA1208E B的VLAN 1接口IP地址为“192.168.0.11”。

2、两台WA1208E上都建立WDS-SSID，名为“wdstest”，绑定在WDS接口下，并通过peer-mac的方式与对端WA1208E进行WDS连接。

3、两台WA1208E配置相同的信道6。

4、两台WA1208E的WDS接口为Trunk端口，同时WA1208E的以太口及与其相连的交换机的端口也都为Trunk端口。

三、配置步骤

WA1208E A 配置步骤如下：

1、在WA1208E A中配置VLAN 1接口IP地址。

<H3C>system

Enter system view , return user view with Ctrl+Z.

[H3C]interface vlan-interface 1

[H3C-Vlan-interface1]ip address 192.168.0.10 255.255.255.0 immediate

[H3C-Vlan-interface1]quit

2、创建两个VLAN，VLAN 2和VLAN 3                                                        

[H3C] vlan 2                                                                     

[H3C-vlan2] quit   

[H3C] vlan 3                                                           

[H3C-vlan3] quit   

3、在WA1208E A中操作，配置使用信道6。

[H3C]radio module 1

[H3C-radio-module1]channel 6

[H3C-radio-module1]quit

[H3C]

4、在WA1208E A中配置WDS-SSID，绑定到wds1/5。配置WDS接口对端的MAC地址为：00e0-fc00-0002。

[H3C]wds-ssid wdstest

New wds-ssid!

[H3C-wssid-wdstest]quit

[H3C]interface wds 1/5

[H3C-Wds1/5]bind wds wdstest

 bind the wds-ssid sucessfully!

[H3C-Wds1/5]peer mac 00e0-fc00-0002

Set wds interface peer MAC successfully!

[H3C-Wds1/5]

5、在WDS试图下，配置WDS为Trunk 端口。

[H3C]wds-ssid wdstest

[H3C-wssid-wdstest]set link-type trunk

[H3C-wssid-wdstest]set trunk permit vlan all

[H3C-wssid-wdstest]quit

[H3C]

6、在以太接口试图下，配置以太口为Trunk端口。                                                    

[H3C] interface Ethernet 0/1                                                    

[H3C-Ethernet0/1]                                                                                                     

[H3C-Ethernet0/1] port link-type trunk                                                                          

[H3C-Ethernet0/1] port trunk permit vlan all

WA1208E B配置步骤如下：

1、在WA1208E B中配置VLAN 1接口IP地址。

<H3C>system

Enter system view , return user view with Ctrl+Z.

[H3C]interface vlan-interface 1

[H3C-Vlan-interface1]ip address 192.168.0.11 255.255.255.0 immediate

[H3C-Vlan-interface1]quit

2、创建两个VLAN，VLAN 2和VLAN 3                                                         

[H3C] vlan 2                                                                     

[H3C-vlan2] quit   

[H3C] vlan 3                                                           

[H3C-vlan3] quit  

3、在WA1208E B中操作，配置使用信道6。

[H3C]radio module 1

[H3C-radio-module1]channel 6

[H3C-radio-module1]quit

[H3C]

4、在WA1208E B中配置WDS-SSID，绑定到wds1/5。配置WDS接口对端的MAC地址为：00e0-fc00-0001。

[H3C]wds-ssid wdstest

New wds-ssid!

[H3C-wssid-wdstest]quit

[H3C]interface wds 1/5

[H3C-Wds1/5]bind wds wdstest

 bind the wds-ssid sucessfully!

[H3C-Wds1/5]peer mac 00e0-fc00-0001

Set wds interface peer MAC successfully!

[H3C-Wds1/5]

5、在WDS试图下，配置WDS为Trunk 端口。

[H3C]wds-ssid wdstest

[H3C-wssid-wdstest]set link-type trunk

[H3C-wssid-wdstest]set trunk permit vlan all

[H3C-wssid-wdstest]quit

[H3C]

6、在以太接口试图下，配置以太口为Trunk端口。                                         

[H3C] interface Ethernet 0/1                                                    

[H3C-Ethernet0/1]                                                                                                      

[H3C-Ethernet0/1] port link-type trunk                                                                          

[H3C-Ethernet0/1] port trunk permit vlan all

四、配置关键点

两台WA1208E的WDS接口必须配置相同的信道。