AR系列路由器debugging PIM DM命令
【命令】
debugging PIM DM { alert | all | mrt | recv | send | timer | warning }
undo debugging PIM DM { alert | all | mrt | recv | send | timer | warning }
【视图】
用户视图
【参数】
alert: PIM DM声明信息开关。
all: PIM DM的所有调试信息。
mrt: PIM DM路由表调试信息。
recv: PIM DM主机调试信息。
Send: PIM DM报文调试信息。
Timer: PIM DM定时器调试信息。
Warning: PIM DM警告调试信息
【描述】
debugging PIM DM命令用来打开PIM DM的调试信息开关
undo debugging PIM DM命令用来关闭PIM DM的调试信息开关。
缺省情况下,PIM DM的调试信息开关是关闭的。
表1:debugging pim dm 命令输出信息列表
字段
含义
All PIM DM debugging switch is on
表明是打开所有的PIM DM调试信息开关
PIM-DM MRT operation debugging switch is on
PIM DM路由信息调试功能被打开
PIM-DM alert debugging switch is on
PIM DM事件信息调试功能被打开
PIM-DM all packet recv debugging switch is on
PIM DM接收报文调试功能被打开
PIM-DM all packet send debugging switch is on
PIM DM发送报文调试信息功能被打开
PIM-DM timer debugging switch is on
PIM DM计时器调试信息功能被打开
PIM-DM warning debugging switch is on
PIM DM警告调试信息功能被打开
表2:debugging pim dm alert命令输出信息列表
字段
含义
SG PRUNE: (S,G)
SG(S,G)剪枝
SG PRUNE: (S,G), but route not found in PIM-DM MRT!
SG(S,G)剪枝,但是路由器没有发现PIM DM MRT
SG CREATION: (S,G)
创建SG项
WRONGIF: (S,G), Ethernet0/0(X.X.X.X), no downstream
组(S,G)在接口e0/0上没有下游
表3:debugging pim dm mrt命令输出信息列表
字段
含义
Ready to make pruned downstream Vlan-interface101(X.X.X.X) of (S,G)forwarding
已经准备好使用被剪枝的下游vlan101进行转发
Ready to delete downstream Vlan-interface101(X.X.X.X) from (S,G)
已经准备好删除将下游vlan101从组(S,G)中删除
Set (S,G)'s upstream to Vlan-interface104(X.X.X.X), neighbor NULL
设置(S,G)的上游vlan 为vlan104
Upstream interface Vlan-interface104(10.110.0.1) added to (10.110.0.2/32, 225.0.0.1/32)
上游接口vlan104加入组(S,G)
Adding downstream interface Vlan-interface101(X.X.X.X) to (S,G)
添加vlan101的下游接口
Ready to create a downstream Vlan-interface101(X.X.X.X) in (S,G)
已经准备好创建vlan104的下游接口
Adding downstream interface Vlan-interface103(X.X.X.X) to (S,G)
添加下游接口vlan103到组(S,G)
Ready to prune a downstream Vlan-interface101(X.X.X.X) from (S,G)
已经准备好剪除下游接口vlan101
表4:debugging pim dm recv/send命令输出信息列表
字段
含义
assert
接收到/发送PIM DM声明报文
Graft
接收到/发送PIM DM嫁接报文
Graft-ack
接收到/发送PIM DM嫁接回应报文
join
接收到/发送PIM DM组加入报文
prune
接收到/发送PIM DM剪枝报文
表5:debugging pim dm timer命令输出信息列表
字段
含义
It's time to clean up PIM-DM MRT
MRT老化计时器超时,开始清除组播路由表
It's time to update PIM-DM MRT
PIM DM 路由表更新计时器超时,开始更新组播路由表
Interface Ethernet0/0/0(X.X.X.X) 's neighbor 12.110.0.1 timeout
E0/0/0的PIM DM 邻居12.110.0.1超时,邻居将被删除
Arranging next PIM-DM MRT cleaning up after 15 seconds
安排在15秒后下一次PIM DM MRT清除
Create PIM NBR timeout Timer on interface Vlan-interface104(10.110.0.1)
PIM TIMER信息,在vlan 104上创建PIM NBR超时计时器
Start pim hello packet send timer on interface Vlan-interface104(10.110.0.1)
在vlan104上的PIM hello报文的发送计时器开始计时
表6:debugging pim dm warning命令输出信息列表
字段
含义
Cannot send join/prune, no upstream router specified!
不能发送join/prune,没有上游路由器
该案例暂时没有网友评论
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作