FIC-FXS/FXO Modules of H3C Series Routers
I. Introduction
FIC-2FXS/FIC-4FXS is the short of 2/4-port voice user circuit interface modules, which is primarily designed to provide the access and process of 2/4-way common analog telephone, Fax or telephone exchange AT0 loop relay, and enable the transmission of voice signals on data communication network; FIC-2FXO/FIC-4FXO is the short of 2/4-port voice AT0 analog relay link process unit, which is primarily designed to provide the access and process of 2/4-way common analog telephone, Fax or telephone exchange AT0 loop relay, and enable the transmission of voice signals on data communication network
Note:
When connecting FIC-2FXS/FIC-2FXO and FIC-4FXS/FIC-4FXO modules, make sure that AR 46 series router can connect to IP network or other WANs.
II. Module Appearance
FIC-2FXS/FIC-2FXO/FIC-4FXS/FIC-4FXO indicator implication
LINK |
Extinguished indicates a connection is not established. Lighted indicates a connection is established. |
ACT |
Extinguished indicates the channel is idle. Lighted indicates a call occurs. |
III. Module Interface Cable
The foreign interface of FIC-2FXS/FIC-2FXO and FIC-4FXS/FIC-4FXO is standards-based RJ45 interface.
FIC-2FXS/FIC-2FXO and FIC-4FXS/FIC-4FXO cable is a line with magnetic ring, and both ends use RJ11 connector.
& Note:
l To ensure the consistency of link process unit socket, the RJ 45 socket of FXO/FXS is compatible with RJ11 plug, which does not affect the real usage.
l The standard configuration of FIC-2FXS/FIC-2FXO and FIC-4FXS/FIC-4FXO modules includes interface cables.
Connection of interface cables
Note:
l When laying the interface cable of FIC-2FXS/FIC-2FXO and FIC-4FXS/FIC-4FXO modules outside, to achieve better lightning effect, user should deploy special lightning arrester in the input terminal of cable.
l Please identify the marks on the interface when connection so that wrong insertion can be avoided to cause link process unit or router host damage.
l To ensure the magnetic compatibility of the overall router, user should connectes the side of line with magnetic ring to the router.
Step 1: Insert the side of cable with magnetic ring in a RJ45 interface of FIC-FXS/FIC-FXO;
Step 2: Connect the other side of cable to the following devices:
If FIC-FXS module is selected, connect the cable to telephone, fax or telephone exchange AT0 loop relay interface.
If FIC-FXO module is selected, connect the cable to the common line of telephone exchange.
IV. Module Interface Attribute
FIC-2FXS/FIC-2FXO and FIC-4FXS/FIC-4FXO interface attribute is shown as follows:
Table 1 FIC-2FXS/FIC-2FXO and FIC-4FXS/FIC-4FXO interface attribute
Attribute |
Description |
Type of connector |
RJ45 |
Connector number |
2(FIC-2FXS/FIC-2FXO) 4(FIC-4FXS/FIC-4FXO) |
Interface standard |
Line with magnetic ring |
Type of cable |
User circuit interface (FIC-2FXS/FIC-4FXS) complies with ITU Q.512. Overcurrent protection and overvoltage protection comply with ITU K.20. |
Dial-in mode |
Support DTMF (Dual-Tone MultiFrequency) and comply with GB3378, not pulse dialing. |
Bandwidth |
300~3400Hz |
该案例暂时没有网友评论
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作