The configuration of RIPng In MSR Series

The configuration of RIPng In MSR Series

Keywords: MSR;RIPng;IPv6

I            Requirement for the diagram

Three MSR running RIPng to communicate.

Device List: 3 MSR;

CMW Version: Version 5.20, Beta 1105

II          Network topology

Figure 1 RIPng

IP address：

设备	接口	Ipv6地址
RTA	E0/0	2::1/64
	E0/1	1::1/64
RTB	E0/0	3::2/64
	E0/1	4::1/64
RTC	G0/0	2::2/64
	G0/1	3::164
PCA		1::2/64
PCB		4::2/64

  

III        Steps of configuration

 

1) Connect devices as showed above;

2)  Config IPv6 address, and running IPv6 on each devices;

 

Example of PCB IPv6 address :

C:\>ipv6 install      

C:\>ipconfig            

Windows IP Configuration

Ethernet adapter 本地连接:

        Connection-specific DNS Suffix . :

        IP Address. . . . . . . . . . . . : 4.0.0.2

        Subnet Mask . . . . . . . . . . . : 255.255.255.0

        IP Address. . . . . . . . . . . . : fe80::212:3fff:fe17:fdab%6 //由此处获得接口索引为6

        Default Gateway . . . . . . . . . : 4.0.0.1

Tunnel adapter Teredo Tunneling Pseudo-Interface:

        Connection-specific DNS Suffix . :

        IP Address. . . . . . . . . . . . : fe80::5445:5245:444f%5

        Default Gateway . . . . . . . . . :

Tunnel adapter 6to4 Tunneling Pseudo-Interface:

        Connection-specific DNS Suffix . :

        IP Address. . . . . . . . . . . . : 2002:400:2::400:2

        Default Gateway . . . . . . . . . :

Tunnel adapter Automatic Tunneling Pseudo-Interface:

        Connection-specific DNS Suffix . :

        IP Address. . . . . . . . . . . . : fe80::5efe:4.0.0.2%2

        Default Gateway . . . . . . . . . :

 

C:\>ipv6 adu 6/1::2          //set IPv6 address to 1::2

C:\>ipconfig               //check result

Ethernet adapter 本地连接:

        Connection-specific DNS Suffix . :

        IP Address. . . . . . . . . . . . : 4.0.0.2

        Subnet Mask . . . . . . . . . . . : 255.255.255.0

        IP Address. . . . . . . . . . . . : 1::2

        IP Address. . . . . . . . . . . . : fe80::212:3fff:fe17:fdab%6

        Default Gateway . . . . . . . . . : 4.0.0.1

note：if you want to cancel this IPv6 address on PC：

    C:\>ipv6 adu 6/1::2 life 0 

【RTB】配置:

<RTB>sys

System View: return to User View with Ctrl+Z.

[RTB]ipv6                       

[RTB]ripng 1

[RTB-ripng-1]q

[RTB]interface Ethernet 0/1

[RTB-Ethernet0/1]ipv6 address 4::1/64//set E0/1 IPv6 address

[RTB-Ethernet0/1]ripng 1 enable//enable RIPng

[RTB-Ethernet0/1]quit         

[RTB]interface Ethernet 0/0

[RTB-Ethernet0/0]ipv6 address 3::2/64     

[RTB-Ethernet0/0]ripng 1 enable//enable RIPng

[RTB-Ethernet0/0]quit       

 

【RTA】配置:

< RTA >sys

System View: return to User View with Ctrl+Z.

[RTA]ipv6                             //enable Ipv6

[RTB]ripng 1

[RTB-ripng-1]q

[RTA]interface Ethernet 0/1

[RTA-Ethernet0/1] ipv6 address 1::1/64    //connect PC

[RTA-Ethernet0/1]ripng 1 enable//enable RIPng

[RTA-Ethernet0/1]quit      

[RTA]interface Ethernet 0/0

[RTA-Ethernet0/0]ip add 2::1/64   //config E0/0 Ipv6 address

[RTA-Ethernet0/0]ripng 1 enable //enable RIPng

[RTA-Ethernet0/0]quit         

 

【RTC】配置:     

<RTC>sys

[RTA]ipv6                             //enable Ipv6

[RTB]ripng 1

[RTB-ripng-1]q

[RTC]interface GigabitEthernet 0/0

[RTC-GigabitEthernet0/0]ipv6 address 2::2/64

[RTA-Ethernet0/0]ripng 1 enable//enalbe RIPng

[RTC-GigabitEthernet0/0]quit

[RTC]interface GigabitEthernet 0/1

[RTC-GigabitEthernet0/1]ipv6 address 3::1/64

[RTA-Ethernet0/1]ripng 1 enable//enalbe RIPng

[RTC-GigabitEthernet0/1]quit

 

PCB上配置默认路由：

C:\>ipv6 rtu ::/0 6/4::1   //default next hop is 4::1

PCA上配置默认路由：

C:\>ipv6 rtu ::/0 4/1::1   //set defautl gateway of PC 1::1

IV       Key notes in the configuration

1) Must running RIPng under according interface. RIPng is not enabled as default.

V         Result Check

Routers can communicate eachother through RIPng.