The configuration of IPv6 PIM-DM In MSR Series

The configuration of IPv6 PIM-DM In MSR Series

 

 

Keywords:MSR;IPv6 PIM-DM;MLD;Multicast

I            Requirement for the diagram

The interface E0/0 connect multicase source, interface S0/1 connect RTB, interface E0/1 connect host Receiver1, running IPv6 PIM-DM under every interface. Running MLD protocol under the interface E0/1; S0/2 of RTB connect RTA, interface S0/2 connect RTC, interface E0/1 connect host Receiver2, running IPv6 PIM-DM under every interface, running MLD protocol under interface E0/1; The interface S0/2 connect RTB, interface E0/1 connect host Receiver3, running IPv6 PIM-DM under every interface, running MLD under E0/1.

Device List: 3, MSR

CMW Version: version 5.20, Beta 1106

II          Network topology

Figure 1  IPv6 PIM-DM

III        Steps of configuration

RTA

#  //Enable IPv6 under global view  ipv6 #  //Enable IPv6 Multicast under global view  multicast ipv6 routing-enable #  //Enable Ripng of IPv6 under golbal view  ripng 1 # //Connect the multicast source of IPv6 interface Ethernet0/0  ipv6 address 6::1/64  undo ipv6 nd ra halt  //Enable Ripng  ripng 1 enable  //Enable pim ipv6 dm  pim ipv6 dm # //Connect IPv6 multicast receiver Receiver1 interface Ethernet0/1  ipv6 address 3::1/64  undo ipv6 nd ra halt  //Eable Ripng  ripng 1 enable  //Enable mldv2  mld enable  mld version 2 # //Connect RTB interface Serial0/1  link-protocol ppp  ipv6 address 1::1/64  //Enable Ripng  ripng 1 enable  //Enable pim ipv6 dm  pim ipv6 dm #

RTB关键配置脚本

#  //Enable IPv6 under global view  ipv6 #  //Running IPv6 multicast under global view  multicast ipv6 routing-enable #  //Enable IPv6 Ripng under global view  ripng 1 # //Connect IPv6 multicast receiver Receiver 2 interface Ethernet0/1  ipv6 address 4::1/64  undo ipv6 nd ra halt  //Enable ripng  ripng 1 enable  //Enable mldv2  mld enable  mld version 2 # //Connect RTC interface Serial0/1  link-protocol ppp  ipv6 address 2::1/64  //Enable ripng  ripng 1 enable  //Enable pim ipv6 dm  pim ipv6 dm # //Connect RTA interface Serial0/2  link-protocol ppp  ipv6 address 1::2/64  //Enable ripng  ripng 1 enable  //Enable pim ipv6 dm  pim ipv6 dm #

RTC

#  //Enable IPv6 under global view  ipv6 #  //Running IPv6 multicast under global view  multicast ipv6 routing-enable #  //Enable IPv6 Ripng under global view  ripng 1 # //Connect IPv6 multicast receiver Receiver3 interface Ethernet0/1  ipv6 address 5::1/64  undo ipv6 nd ra halt  //Enable ripng  ripng 1 enable  //Enable mldv2  mld enable  mld version 2 #   //Connect RTB interface Serial0/2  link-protocol ppp  ipv6 address 2::2/64  //Enable ripng  ripng 1 enable  //Enable pim ipv6 dm  pim ipv6 dm #

 

IV       Key notes in the configuration

1) Make sure they could communicate with each other of RTA,RTB,RTC base on Ripng;

2) Enable IPv6 under global view;

3) Enable IPv6 Multicast under global view;

4) Make sure enable IPv6 Multicast under every router, and every interface that connect with other router enable IPv6 PIM-DM;

5) Enable MLD under every edge interface;

6) Server sending out multicast package, Receiver sending mld report package;

7) Using command below to check the result：

display pim ipv6 routing-table

display multicast ipv6 forwarding-table