The configuration of OSPFv3 Double Process In MSR Series

The configuration of OSPFv3 Double Process In MSR Series

 

 

Keywords: MSR;IPv6;OSPFv3

I            Requirement for the diagram

Using OSPFv3 as routing protocol and transfer routing info, make the loopback address of RTA and RTC can reach each other.

Device List: 3 MSR

CMW Version: Version 5.20, Beta 1106

II          Network topology

Figure 1 OSPFv3 Double Process

IP address list：

Device	Interface	Ipv6 address
RTA	LoopBack1	100::1/128
	E0/1	1::1/64
	Ospfv3 router id	1.1.1.1
RTB	E0/0	2::2/64
	E0/1	1::2/64
	Ospfv3 router id	2.2.2.2
RTC	LoopBack1	200::1/128
	G0/1	2::164
	Ospfv3 router id	3.3.3.3

 

III        Steps of configuration

RTA

#  ipv6 # //set ip address of E0/1 //added this address to area 0,process 100 of ospfv3 # interface Ethernet0/1  port link-mode route  ipv6 address 1::1/64  ospfv3 100 area 0.0.0.0 //set the address of LoopBack1 // added this address to area 0,process 100 of ospfv3 # interface LoopBack1  ipv6 address 100::1/128  ospfv3 100 area 0.0.0.0 //setup process 100, area 0 # ospfv3 100  router-id 1.1.1.1  area 0.0.0.0

RTB配置

#  ipv6 //set ip address of E0/0 //added this address to area 0,process 200 of ospfv3 # interface Ethernet0/0  port link-mode route  ipv6 address 2::2/64  ospfv3 200 area 0.0.0.0 //set ip address of E0/1 //added this address to area 0,process 100 of ospfv3 # interface Ethernet0/1  port link-mode route  ipv6 address 1::2/64  ospfv3 100 area 0.0.0.0  //setup process 100, area 0 # ospfv3 100  router-id 21.21.21.21  //import direct routing  import-route direct  //import routing info of process 200 of ospfv3  import-route ospfv3 200  area 0.0.0.0 //setup process 200, area 0 #              ospfv3 200  router-id 22.22.22.22  //import direct routing  import-route direct  //import routing info of process 100 of ospfv3  import-route ospfv3 100  area 0.0.0.0 # return

RTC

#  ipv6 # interface NULL0 //set the address of LoopBack1 //added this address to area 0,process 100 of ospfv3 # interface LoopBack1  ipv6 address 200::1/128  ospfv3 200 area 0.0.0.0 # interface GigabitEthernet0/0  port link-mode route //set ip address of G0/1 //added this address to area 0,process 200 of ospfv3 # interface GigabitEthernet0/1  port link-mode route  ipv6 address 2::1/64  ospfv3 200 area 0.0.0.0 //setup process 200, area 0   # ospfv3 200  router-id 3.3.3.3  area 0.0.0.0

 

IV       Key notes in the configuration

   Make sure the process number and the routing import of each other.

V         Result Check

Font,Arial,Size,NO.12, Row Spacing--1.5 lines

After configuration above, RTA and RTC can reachable each other:

[RTA-2021]ping ipv6 200::1

  PING 200::1 : 56 data bytes, press CTRL_C to break

    Reply from 200::1

    bytes=56 Sequence=1 hop limit=63 time = 2 ms

    Reply from 200::1

    bytes=56 Sequence=2 hop limit=63 time = 2 ms

    Reply from 200::1

    bytes=56 Sequence=3 hop limit=63 time = 2 ms

    Reply from 200::1

    bytes=56 Sequence=4 hop limit=63 time = 2 ms

    Reply from 200::1

    bytes=56 Sequence=5 hop limit=63 time = 2 ms

 

  --- 200::1 ping statistics ---

    5 packet(s) transmitted

    5 packet(s) received

    0.00% packet loss

    round-trip min/avg/max = 2/2/2 ms

 

The routing table of RTB：

<RTB-2020>display ospfv routing

 E1 - Type 1 external route,   IA - Inter area route,   I - Intra area route

 E2 - Type 2 external route,   * - Selected route

             OSPFv3 Router with ID (21.21.21.21) (Process 100)

 ------------------------------------------------------------------------

 *Destination: 1::/64                                      

  Type      : I                                       Cost    : 1

  NextHop   : directly-connected                      Interface: Eth0/1

 

 *Destination: 100::1/128                                  

  Type      : I                                       Cost    : 1

  NextHop   : FE80::20F:E2FF:FE3A:FF54                Interface: Eth0/1

 

 

            OSPFv3 Router with ID (22.22.22.22) (Process 200)

 ------------------------------------------------------------------------

 *Destination: 2::/64                                      

  Type      : I                                       Cost    : 1

  NextHop   : directly-connected                      Interface: Eth0/0

               

 *Destination: 200::1/128                                  

  Type      : I                                       Cost    : 1

  NextHop   : FE80::20F:E2FF:FE3A:FE8C                Interface: Eth0/0