H3C SecPath U系列UTM200-S版本升级指导

H3C SecPath U系列UTM200-S版本升级指导

 

注：UTM200-S升级至B5105P04及以后的版本, 必须要升级Bootware至 1.12及以后的版本。

 

 

1． 升级BOOTWARE

BootWare Validating...

Press Ctrl+B to enter extended boot menu...

Please input BootWare password:

Note: The current operating device is flash

Enter < Storage Device Operation > to select device.

===========================<EXTEND-BOOTWARE MENU>===========================

|<1> Boot System                                                           |

|<2> Enter Serial SubMenu                                                  |

|<3> Enter Ethernet SubMenu                                                |

|<4> File Control                                                          |

|<5> Modify BootWare Password                                              |

|<6> Skip Current System Configuration                                     |

|<7> BootWare Operation Menu                                               |

|<8> Clear Super Password                                                  |

|<9> Storage Device Operation                                              |

|<0> Reboot                                                                |

============================================================================

Enter your choice(0-9):7

=========================<BootWare Operation Menu>==========================

|Note:the operating device is flash                                        |

|<1> Backup Full BootWare                                                  |

|<2> Restore Full BootWare                                                 |

|<3> Update BootWare By Serial                                             |

|<4> Update BootWare By Ethernet                                           |

|<0> Exit To Main Menu                                                     |

============================================================================

Enter your choice(0-4): 3

====================<BOOTWARE OPERATION SERIAL SUB-MENU>====================

|<1> Update Full BootWare                                                  |

|<2> Update Extend BootWare                                                |

|<3> Update Basic BootWare                                                 |

|<4> Modify Serial Interface Parameter                                     |

|<0> Exit To Main Menu                                                     |

============================================================================

Enter your choice(0-4): 4

===============================<BAUDRATE SET>===============================

|Note:'*'indicates the current baudrate                                    |

|     Change The HyperTerminal's Baudrate Accordingly                      |

|---------------------------<Baudrate Avaliable>---------------------------|

|<1> 9600(Default)*                                                        |

|<2> 19200                                                                 |

|<3> 38400                                                                 |

|<4> 57600                                                                 |

|<5> 115200                                                                |

|<0> Exit                                                                  |

============================================================================

Enter your choice(0-5): 5

Baudrate has been changed to 115200 bps.     修改串口波特率为115200

Please change the terminal's baudrate to 115200 bps, press ENTER when ready.

此时需修改设备的串口波特率，通过串口服务器修改可能有问题，可以直接通过PC的串口连接设备，再利用“附件-à通讯-à超级终端”继续进行以下的设置。

The current baudrate is 115200 bps

===============================<BAUDRATE SET>===============================

|Note:'*'indicates the current baudrate                                    |

|     Change The HyperTerminal's Baudrate Accordingly                      |

|---------------------------<Baudrate Avaliable>---------------------------|

|<1> 9600(Default)                                                         |

|<2> 19200                                                                 |

|<3> 38400                                                                 |

|<4> 57600                                                                 |

|<5> 115200*                                                               |

|<0> Exit                                                                  |

============================================================================

Enter your choice(0-5): 0

====================<BOOTWARE OPERATION SERIAL SUB-MENU>=================

|<1> Update Full BootWare                                                  |

|<2> Update Extend BootWare                                                |

|<3> Update Basic BootWare                                                 |

|<4> Modify Serial Interface Parameter                                     |

|<0> Exit To Main Menu                                                     |

Enter your choice(0-4): 1

Please Start To Transfer File, Press <Ctrl+C> To Exit.

Waiting ...CC                    串口下发送 utm  bootware文件

此时，需在工具栏的“传送”，点击“发送文件”，如图，文件名选择bootware升级文件。

Download successfully!        //下载bootware升级文件成功

303872 bytes downloaded!

Updating Basic BootWare? [Y/N]Y

Updating Basic BootWare...............Done!

Updating Extend BootWare? [Y/N]Y

Updating Extend BootWare.............Done!

 

===============================<BAUDRATE SET>===============================

|Note:'*'indicates the current baudrate                                    |

|     Change The HyperTerminal's Baudrate Accordingly                      |

|---------------------------<Baudrate Avaliable>---------------------------|

|<1> 9600(Default)                                                         |

|<2> 19200                                                                 |

|<3> 38400                                                                 |

|<4> 57600                                                                 |

|<5> 115200*                                                               |

|<0> Exit                                                                  |

============================================================================

Enter your choice(0-5): 1

Baudrate has been changed to 9600 bps.  修改串口波特率为9600

Please change the terminal's baudrate to 9600 bps, press ENTER when ready.

The current baudrate is 9600 bps

 

===============================<BAUDRATE SET>===============================

|Note:'*'indicates the current baudrate                                    |

|     Change The HyperTerminal's Baudrate Accordingly                      |

|---------------------------<Baudrate Avaliable>---------------------------|

|<1> 9600(Default)*                                                        |

|<2> 19200                                                                 |

|<3> 38400                                                                 |

|<4> 57600                                                                 |

|<5> 115200                                                                |

|<0> Exit                                                                  |

============================================================================

Enter your choice(0-5): 0

 

 

升级软件版本：

1．  本机搭建好TFTP服务器，将软件版本5105P04.BIN放入其中。

TFTP Server（1.1.1.1）-----------------------------g0/0 UTM

 

===========================<EXTEND-BOOTWARE MENU>===========================

|<1> Boot System                                                           |

|<2> Enter Serial SubMenu                                                  |

|<3> Enter Ethernet SubMenu                                                |

|<4> File Control                                                          |

|<5> Modify BootWare Password                                              |

|<6> Skip Current System Configuration                                     |

|<7> BootWare Operation Menu                                               |

|<8> Clear Super Password                                                  |

|<9> Storage Device Operation                                              |

|<0> Reboot                                                                |

============================================================================

Enter your choice(0-9):                输入ctrl+F,格式化文件系统

 

Warning:All things will lost!Are you sure to format? [Y/N]Y.................

............................................................................

......................................

Format success.

 

===========================<EXTEND-BOOTWARE MENU>===========================

|<1> Boot System                                                           |

|<2> Enter Serial SubMenu                                                  |

|<3> Enter Ethernet SubMenu                                                |

|<4> File Control                                                          |

|<5> Modify BootWare Password                                              |

|<6> Skip Current System Configuration                                     |

|<7> BootWare Operation Menu                                               |

|<8> Clear Super Password                                                  |

|<9> Storage Device Operation                                              |

|<0> Reboot                                                                |

============================================================================

Enter your choice(0-9):3

 

==========================<Enter Ethernet SubMenu>==========================

|Note:the operating device is flash                                        |

|<1> Download Application Program To SDRAM And Run                         |

|<2> Update Main Application File                                          |

|<3> Update Backup Application File                                        |

|<4> Update Secure Application File                                        |

|<5> Modify Ethernet Parameter                                             |

|<0> Exit To Main Menu                                                     |

|<Ensure The Parameter Be Modified Before Downloading!>                    |

============================================================================

Enter your choice(0-5): 5

==========================<ETHERNET PARAMETER SET>==========================

|Note:       '.' = Clear field.                                            |

|            '-' = Go to previous field.                                   |

|          Ctrl+D = Quit.                                                  |

============================================================================

Protocol (FTP or TFTP)   :fdfdf tftp

Load File Name         :dfdf B5105P04.BIN

Target File Name        :dfdf B5105P04.BIN

Server IP Address        :dfdf 1.1.1.1

Local IP Address         :dfdf 1.1.1.2

Gateway IP Address       :sdfsdf 0.0.0.0

==========================<Enter Ethernet SubMenu>==========================

|Note:the operating device is flash                                        |

|<1> Download Application Program To SDRAM And Run                         |

|<2> Update Main Application File                                          |

|<3> Update Backup Application File                                        |

|<4> Update Secure Application File                                        |

|<5> Modify Ethernet Parameter                                             |

|<0> Exit To Main Menu                                                     |

|<Ensure The Parameter Be Modified Before Downloading!>                    |

============================================================================

Enter your choice(0-5): 2

Loading......................................................................................................................................

==========================<Enter Ethernet SubMenu>==========================

|Note:the operating device is flash                                        |

|<1> Download Application Program To SDRAM And Run                         |

|<2> Update Main Application File                                          |

|<3> Update Backup Application File                                        |

|<4> Update Secure Application File                                        |

|<5> Modify Ethernet Parameter                                             |

|<0> Exit To Main Menu                                                     |

|<Ensure The Parameter Be Modified Before Downloading!>                    |

============================================================================

Enter your choice(0-5): 0

===========================<EXTEND-BOOTWARE MENU>===========================

|<1> Boot System                                                           |

|<2> Enter Serial SubMenu                                                  |

|<3> Enter Ethernet SubMenu                                                |

|<4> File Control                                                          |

|<5> Modify BootWare Password                                              |

|<6> Skip Current System Configuration                                     |

|<7> BootWare Operation Menu                                               |

|<8> Clear Super Password                                                  |

|<9> Storage Device Operation                                              |

|<0> Reboot                                                                |

============================================================================

Enter your choice(0-9): 1

升级完成！