H3C S3500-EA NQA UDP Jitter测试的典型配置
一、 组网需求:
使用UDP-jitter功能测试本端(Device A)和指定的目的端(Device B)之间传送报文的时延抖动。
二、 组网图:
三、 配置步骤:
(1) 配置Device B
# 使能NQA服务器,配置监听的IP地址为10.2.2.2,端口号为9000。
<DeviceB> system-view
[DeviceB] nqa server enable
[DeviceB] nqa server udp-echo 10.2.2.2 9000
(2) 配置Device A
# 创建UDP-jitter类型的NQA测试组并配置相关测试参数。
<DeviceA> system-view
[DeviceA] nqa entry admin test
[DeviceA-nqa-admin-test] type udp-jitter
[DeviceA-nqa-admin-test-udp-jitter] destination ip 10.2.2.2
[DeviceA-nqa-admin-test-udp-jitter] destination port 9000
[DeviceA-nqa-admin-test-udp-jitter] quit
# 启动UDP-jitter测试操作。
[DeviceA] nqa schedule admin test start-time now lifetime forever
# 测试执行一段时间后,停止UDP-jitter测试操作。
[DeviceA] undo nqa schedule admin test
# 显示UDP-jitter测试中最后一次测试的结果。
[DeviceA] display nqa result admin test
NQA entry(admin admin, tag test) test results:
Destination IP address: 10.2.2.2
Send operation times: 10 Receive response times: 10
Min/Max/Average round trip time: 7/10/8
Square-Sum of round trip time: 646
Last succeeded probe time: 2007-11-22 10:16:49.0
Extend results:
Packet lost in test: 0%
Failures due to timeout: 0
Failures due to disconnect: 0
Failures due to no connection: 0
Failures due to sequence error: 0
Failures due to internal error: 0
Failures due to other errors: 0
UDP-jitter results:
RTT number: 10
SD max delay: 5 DS max delay: 5
Min positive SD: 1 Min positive DS: 0
Max positive SD: 1 Max positive DS: 0
Positive SD number: 2 Positive DS number: 0
Positive SD sum: 2 Positive DS sum: 0
Positive SD average: 1 Positive DS average: 0
Positive SD square sum: 2 Positive DS square sum: 0
Min negative SD: 1 Min negative DS: 0
Max negative SD: 2 Max negative DS: 0
Negative SD number: 3 Negative DS number: 0
Negative SD sum: 4 Negative DS sum: 0
Negative SD average: 1 Negative DS average: 0
Negative SD square sum: 6 Negative DS square sum: 0
SD lost packet(s): 0 DS lost packet(s): 0
Lost packet(s) for unknown reason: 0
四、 配置关键点:
UDP-jitter测试中每次探测发送一组报文,这组报文对应一条历史记录。因此,如果想了解UDP-jitter测试的结果,建议通过display nqa result命令来查看探测结果,不要通过display nqa history命令查看历史记录
该案例暂时没有网友评论
✖
案例意见反馈
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作