MSR36-20路由器作为分部接入总部VPN的配置问题

您好，请知：

具体是L2TP OVER IPSEC的什么问题呢？

以下是配置举例，请参考：

3.1  组网需求

如图1所示，Host通过L2TP隧道访问LNS一侧的网络。具体应用需求如下：

·     LAC与LNS自动建立L2TP隧道

·     LAC与LNS之间采用IKE方式建立IPsec安全隧道来对L2TP流量进行加密。

图1 MSR系列路由器L2TP over IPsec典型配置组网图

3.2  使用版本

本举例是在R0106版本上进行配置和验证的。

3.3  配置步骤

3.3.1  LNS的配置

# 配置本地用户1，设置密码为1234。

<LNS> system-view

[LNS] local-user 1 class network

[LNS-luser-network-1] password simple 1234

[LNS-luser-network-1] service-type ppp

[LNS-luser-network-1] quit

# 配置ISP域system对PPP用户采用本地验证。

[LNS] domain system

[LNS-isp-system] authentication ppp local

[LNS-isp-system] quit

# 使能L2TP。

[LNS] l2tp enable

# 配置虚模板Virtual-Template1配置接口的IP地址为192.168.0.1/24，PPP认证方式为PAP，并指定为PPP用户分配的IP地址为192.168.0.2。

[LNS] interface virtual-template 1

[LNS-Virtual-Template1] ip address 192.168.0.1 24

[LNS-Virtual-Template1] ppp authentication-mode pap domain system

[LNS-Virtual-Template1] remote address 192.168.0.2

[LNS-Virtual-Template1] quit

# 创建LNS模式的L2TP组1，配置隧道本端名称为lns，指定接收呼叫的虚拟模板接口为VT1，并配置L2TP隧道对端名为lac。

[LNS] l2tp-group 1 mode lns

[LNS-l2tp1] tunnel name lns

[LNS-l2tp1] undo tunnel authentication

[LNS-l2tp1] allow l2tp virtual-template 1 remote lac

[LNS-l2tp1] quit

# 配置访问控制列表。

[LNS] acl number 3000

[LNS-acl-adv-3000] rule permit ip source 10.0.0.2 0 destination 10.0.0.1 0

[LNS-acl-adv-3000] quit

# 配置IKE keychain。

[LNS] ike keychain l2tp

# 配置与地址为10.0.0.1的对端使用的预共享密钥为明文的abcd。

[LNS-ike-keychain-l2tp] pre-shared-key address 10.0.0.1 key simple abcd

[LNS-ike-keychain-l2tp] quit

#在IKE profile l2tp中指定名称为l2tp的配置的IKE keychain。

[LNS] ike profile l2tp

[LNS-ike-profile-l2tp] keychain l2tp

# 指定使用IP地址10.0.0.2标识本端身份。

[LNS-ike-profile-l2tp] local-identity address 10.0.0.2

# 指定需要匹配对端身份类型为IP地址，取值为10.0.0.1。

[LNS-ike-profile-l2tp] match remote identity address 10.0.0.1

[LNS-ike-profile-l2tp] quit

# 配置IPsec安全协议。

[LNS] ipsec transform-set l2tp

# 配置IPsec安全提议采用的ESP加密算法为CBC模式的3DES算法。

[LNS-ipsec-transform-set-l2tp] esp encryption-algorithm 3des-cbc

# 配置IPsec安全提议采用的ESP认证算法为MD5。

[LNS-ipsec-transform-set-l2tp] esp authentication-algorithm md5

[LNS-ipsec-transform-set-l2tp] quit

# 配置IPsec安全策略引用ACL 3000和名字为l2tp的IPsec安全提议，并指定IPsec隧道的对端IPv4地址为10.0.0.1。

[LNS] ipsec policy l2tp 1 isakmp

[LNS-ipsec-policy-isakmp-l2tp-1] security acl 3000

[LNS-ipsec-policy-isakmp-l2tp-1] transform-set l2tp

[LNS-ipsec-policy-isakmp-l2tp-1] ike-profile l2tp

[LNS-ipsec-policy-isakmp-l2tp-1] remote-address 10.0.0.1

[LNS-ipsec-policy-isakmp-l2tp-1] quit

# 配置连接LAC的接口GigabitEthernet0/0的IP地址并使能IPsec安全策略。

# 配置接口IP地址并使能IPsec安全策略。

[LNS] interface gigabitethernet 0/0

[LNS-GigabitEthernet0/0] ip address 10.0.0.2 24

[LNS-GigabitEthernet0/0] ipsec apply policy l2tp

[LNS-GigabitEthernet0/0] quit

# 配置接口GigabitEthernet0/1的IP地址。

[LNS] interface gigabitethernet 0/1

[LNS-GigabitEthernet0/1] ip address 15.0.0.1 24

[LNS-GigabitEthernet0/1] quit

3.3.2  LAC的配置

# 开启L2TP功能。

<LAC> system-view

[LAC] l2tp enable

# 创建LAC模式的L2TP组1。

[LAC] l2tp-group 1 mode lac

# 配置LAC侧本端名称为LAC，并指定LNS的IP地址为10.0.0.2。

[LAC-l2tp1] tunnel name lac

[LAC-l2tp1] lns-ip 10.0.0.2

[LAC-l2tp1] undo tunnel authentication

[LAC-l2tp1] quit

# 配置访问控制列表。

[LAC] acl number 3000

# 配置ACL的规则。

[LAC-acl-adv-3000] rule permit ip source 10.0.0.1 0 destination 10.0.0.2 0

[LAC-acl-adv-3000] quit

# 配置Virtual-ppp口，配置PPP用户的用户名为1，密码为1234，并配置PPP验证方式为PAP。

[LAC] interface virtual-PPP 1

[LAC-Virtual-PPP1] ip address ppp-negotiate

[LAC-Virtual-PPP1] ppp pap local-user 1 password simple 1234

[LAC-Virtual-PPP1] quit

# 配置私网路由，访问公司总部的报文将通过L2TP隧道转发。

[LAC] ip route-static 15.0.0.1 24 Virtual-PPP 1

# 配置IKE keychain。

[LAC] ike keychain l2tp

# 配置与地址为10.0.0.2的对端使用的预共享密钥为明文的abcd。

[LAC-ike-keychain-l2tp] pre-shared-key address 10.0.0.2 key simple abcd

[LAC-ike-keychain-l2tp] quit

# 在IKE profile l2tp中指定名称为l2tp的配置的IKE keychain。

[LAC] ike profile l2tp

[LAC-ike-profile-l2tp] keychain l2tp

 # 指定使用IP地址10.0.0.1标识本端身份。

[LAC-ike-profile-l2tp] local-identity address 10.0.0.1

# 指定需要匹配对端身份类型为IP地址，取值为10.0.0.2。

[LAC-ike-profile-l2tp] match remote identity address 10.0.0.2

[LAC-ike-profile-l2tp] quit

# 配置Ipsec安全协议。

[LAC] ipsec transform-set l2tp

# 配置IPsec安全提议采用的ESP加密算法为CBC模式的3DES算法。

[LAC-ipsec-transform-set-l2tp] esp encryption-algorithm 3des-cbc

# 配置IPsec安全提议采用的ESP认证算法为MD5。

[LAC-ipsec-transform-set-l2tp] esp authentication-algorithm md5

[LAC-ipsec-transform-set-l2tp] quit

# 配置IPsec安全策略引用ACL 3000和名字为l2tp的IPsec安全提议，并指定IPsec隧道的对端IPv4地址为10.0.0.2。

[LAC] ipsec policy l2tp 1 isakmp

[LAC-ipsec-policy-isakmp-l2tp-1] security acl 3000

[LAC-ipsec-policy-isakmp-l2tp-1] transform-set l2tp

[LAC-ipsec-policy-isakmp-l2tp-1] ike-profile l2tp

[LAC-ipsec-policy-isakmp-l2tp-1] remote-address 10.0.0.2

[LAC-ipsec-policy-isakmp-l2tp-1] quit

# 配置接口GigabitEthernet0/1的IP地址。

[LAC] interface gigabitethernet 0/1

[LAC-GigabitEthernet0/1] ip address 14.0.0.1 24

[LAC-GigabitEthernet0/1] quit

# 配置连接LNS的接口GigabitEthernet0/0的IP地址并使能IPsec安全策略。

[LAC] interface gigabitethernet 0/0

[LAC-GigabitEthernet0/0] ip address 10.0.0.1 24

[LAC-GigabitEthernet0/0] ipsec apply policy l2tp

[LAC-GigabitEthernet0/0] quit

# 执行l2tp-auto-client命令触发LAC建立L2TP隧道。

[LAC] interface virtual-PPP 1

[LAC-Virtual-PPP1] l2tp-auto-client l2tp-group 1

3.4  验证配置

# LAC上可以看到L2TP隧道和L2TP会话的建立情况。

[LAC] display l2tp tunnel

LocalTID RemoteTID State        Sessions RemoteAddress   RemotePort RemoteName

23561    63423     Established  1        10.0.0.2        1701       lns

[LAC] display l2tp session

LocalSID    RemoteSID    LocalTID    State

1538        2562         23561       Established

# LNS上可以看到L2TP隧道和L2TP会话的建立情况。

[LNS] display l2tp tunnel

LocalTID RemoteTID State        Sessions RemoteAddress   RemotePort RemoteName

63423    23561     Established  1        10.0.0.1        1701       lac

[LNS] display l2tp session

LocalSID    RemoteSID    LocalTID    State

2562        1538         63423       Established

# LAC上可以看到IKE SA和IPSec SA的建立情况。

[LAC] display ike sa

    Connection-ID   Remote                Flag         DOI

------------------------------------------------------------------

    5               10.0.0.2              RD           IPSEC

Flags:

RD--READY RL--REPLACED FD-FADING

[LAC]display ipsec sa

-------------------------------

Interface: GigabitEthernet0/0

-------------------------------

  -----------------------------

  IPsec policy: l2tp

  Sequence number: 1

  Mode: isakmp

  -----------------------------

    Tunnel id: 0

    Encapsulation mode: tunnel

    Perfect forward secrecy:

    Path MTU: 1443

    Tunnel:

        local  address: 10.0.0.1

        remote address: 10.0.0.2

    Flow:

    sour addr: 10.0.0.1/255.255.255.255  port: 0  protocol: ip

    dest addr: 10.0.0.2/255.255.255.255  port: 0  protocol: ip

    [Inbound ESP SAs]

      SPI: 987342280 (0x3ad9a5c8)

      Transform set: ESP-ENCRYPT-3DES-CBC ESP-AUTH-MD5

      SA duration (kilobytes/sec): 1843200/3600

      SA remaining duration (kilobytes/sec): 1843181/2339

      Max received sequence-number: 319

      Anti-replay check enable: Y

      Anti-replay window size: 64

      UDP encapsulation used for nat traversal: N

      Status: active

    [Outbound ESP SAs]

      SPI: 2705574035 (0xa143c893)

      Transform set: ESP-ENCRYPT-3DES-CBC ESP-AUTH-MD5

      SA duration (kilobytes/sec): 1843200/3600

      SA remaining duration (kilobytes/sec): 1843182/2339

      Max sent sequence-number: 301

      UDP encapsulation used for nat traversal: N

      Status: active

# LNS上可以看到IKE SA和IPSec SA的建立情况。

[LNS] display ike sa

    Connection-ID   Remote                Flag         DOI

------------------------------------------------------------------

    1               10.0.0.1              RD           IPSEC

Flags:

RD--READY RL--REPLACED FD-FADING

[LNS] display ipsec sa

-------------------------------

Interface: GigabitEthernet0/0

-------------------------------

  -----------------------------

  IPsec policy: l2tp

  Sequence number: 1

  Mode: isakmp

  -----------------------------

    Tunnel id: 0

    Encapsulation mode: tunnel

    Perfect forward secrecy:

    Path MTU: 1443

    Tunnel:

        local  address: 10.0.0.2

        remote address: 10.0.0.1

    Flow:

    sour addr: 10.0.0.2/255.255.255.255  port: 0  protocol: ip

    dest addr: 10.0.0.1/255.255.255.255  port: 0  protocol: ip

    [Inbound ESP SAs]

      SPI: 2705574035 (0xa143c893)

      Transform set: ESP-ENCRYPT-3DES-CBC ESP-AUTH-MD5

      SA duration (kilobytes/sec): 1843200/3600

      SA remaining duration (kilobytes/sec): 1843181/2300

      Max received sequence-number: 310

      Anti-replay check enable: Y

      Anti-replay window size: 64

      UDP encapsulation used for nat traversal: N

      Status: active

    [Outbound ESP SAs]

      SPI: 987342280 (0x3ad9a5c8)

      Transform set: ESP-ENCRYPT-3DES-CBC ESP-AUTH-MD5

      SA duration (kilobytes/sec): 1843200/3600

      SA remaining duration (kilobytes/sec): 1843180/2300

      Max sent sequence-number: 329

      UDP encapsulation used for nat traversal: N

      Status: active

# Host A所属网段可以通过L2TP隧道访问外网。

[LAC] ping -a 14.0.0.1 15.0.0.1

Ping 15.0.0.1 (15.0.0.1) from 14.0.0.1: 56 data bytes, press escape sequence to break

56 bytes from 15.0.0.1: icmp_seq=0 ttl=255 time=0.462 ms

56 bytes from 15.0.0.1: icmp_seq=1 ttl=255 time=0.280 ms

56 bytes from 15.0.0.1: icmp_seq=2 ttl=255 time=0.276 ms

56 bytes from 15.0.0.1: icmp_seq=3 ttl=255 time=0.280 ms

56 bytes from 15.0.0.1: icmp_seq=4 ttl=255 time=0.280 ms

--- Ping statistics for 15.0.0.1 ---

5 packet(s) transmitted, 5 packet(s) received, 0.0% packet loss

round-trip min/avg/max/std-dev = 0.276/0.316/0.462/0.073 ms

[LAC]%Jul  3 14:01:16:689 2013 LAC PING/6/PING_STATIS_INFO: Ping statistics for 15.0.0.1: 5 packet(s) transmitted, 5 packet(

s) received, 0.0% packet loss, round-trip min/avg/max/std-dev = 0.276/0.316/0.462/0.073 ms.