secpath f1000-ak115 ipsec
- 0关注
- 1收藏，1415浏览
问题描述：
请教 secpath f1000-ak115和juniper ssg140 aggressive模式ipsec vpn互联。secpath f1000-ak115方静态地址 ssg140方 pppoe获得的动态地址。配置nat穿透
- 2021-06-30提问
- 举报
-
(0)
最佳答案
您好，请知：
因为有一端是非固定IP的接入，因此需要使用IPSEC+IKE野蛮模式来实现。
以下是配置案例，请参考：
组网说明：
本案例采用H3C HCL模拟器的F1060防火墙来模拟IPSEC+IKE野蛮模式的典型组网配置。在网络拓扑图中存在子网1和子网2.为了保障子网1和子网2相互传输数据的安全性，因此需要在FW1与FW2采用建立IPSEC VPN隧道，由于FW1的出接口地址不固定，因此采用IKE野蛮模式。
配置步骤
1、按照网络拓扑图正确配置IP地址
2、FW1与FW2的互联接口加入安全域，并放通域间策略
3、FW1与FW2建立IPSEC VPN隧道，采用IKE野蛮模式
配置关键点
ISP：
System View: return to User View with Ctrl+Z.
[H3C]sysname ISP
[ISP]int gi 0/0
[ISP-GigabitEthernet0/0]des
[ISP-GigabitEthernet0/0]ip address 202.1.100.1 24
[ISP-GigabitEthernet0/0]dhcp server apply ip-pool 1
[ISP-GigabitEthernet0/0]quit
[ISP]int gi 0/1
[ISP-GigabitEthernet0/1]des
[ISP-GigabitEthernet0/1]ip address 202.2.100.1 30
[ISP-GigabitEthernet0/1]quit
[ISP]ip route-static 192.168.1.0 255.255.255.0 202.1.100.2
[ISP]ip route-static 172.16.1.0 255.255.255.0 202.2.100.2
[ISP]dhcp enable
[ISP]dhcp server ip-pool 1
[ISP-dhcp-pool-1]network 202.1.100.0 mask 255.255.255.0
[ISP-dhcp-pool-1]gateway-list 202.1.100.1
[ISP-dhcp-pool-1]quit
FW1：
System View: return to User View with Ctrl+Z.
[H3C]sysname FW1
[FW1]int gi 1/0/3
[FW1-GigabitEthernet1/0/3]ip address 192.168.1.1 24
[FW1-GigabitEthernet1/0/3]quit
[FW1]int gi 1/0/2
[FW1-GigabitEthernet1/0/2]des
[FW1-GigabitEthernet1/0/2]ip address dhcp-alloc
[FW1-GigabitEthernet1/0/2]quit
[FW1]ip route-static 0.0.0.0 0.0.0.0 202.1.100.1
[FW1]security-zone name Trust
[FW1-security-zone-Trust]import interface GigabitEthernet 1/0/3
[FW1-security-zone-Trust]quit
[FW1]security-zone name Untrust
[FW1-security-zone-Untrust]import interface GigabitEthernet 1/0/2
[FW1-security-zone-Untrust]quit
[FW1]acl basic 2001
[FW1-acl-ipv4-basic-2001]rule 0 permit source any
[FW1-acl-ipv4-basic-2001]quit
[FW1]
[FW1]zone-pair security source trust destination untrust
[FW1-zone-pair-security-Trust-Untrust]packet-filter 2001
[FW1-zone-pair-security-Trust-Untrust]quit
[FW1]
[FW1]zone-pair security source untrust destination trust
[FW1-zone-pair-security-Untrust-Trust]packet-filter 2001
[FW1-zone-pair-security-Untrust-Trust]quit
[FW1]
[FW1]zone-pair security source trust destination local
[FW1-zone-pair-security-Trust-Local]packet-filter 2001
[FW1-zone-pair-security-Trust-Local]quit
[FW1]
[FW1]zone-pair security source local destination trust
[FW1-zone-pair-security-Local-Trust]packet-filter 2001
[FW1-zone-pair-security-Local-Trust]quit
[FW1]
[FW1]zone-pair security source untrust destination local
[FW1-zone-pair-security-Untrust-Local]packet-filter 2001
[FW1-zone-pair-security-Untrust-Local]quit
[FW1]
[FW1]zone-pair security source local destination untrust
[FW1-zone-pair-security-Local-Untrust]packet-filter 2001
[FW1-zone-pair-security-Local-Untrust]quit
FW1 IPSEC+IKE野蛮模式关键配置点：
[FW1]acl advanced 3000
[FW1-acl-ipv4-adv-3000]rule 0 permit ip source 192.168.1.0 0.0.0.255 destination 172.16.1.0 0.0.0.255
[FW1-acl-ipv4-adv-3000]quit
[FW1]ike identity fqdn fw1
[FW1]ike keychain james
[FW1-ike-keychain-james]pre-shared-key address 202.2.100.2 255.255.255.252 key simple james
[FW1-ike-keychain-james]quit
[FW1]ike proposal 1
[FW1-ike-proposal-1]quit
[FW1]ike profile james
[FW1-ike-profile-james]keychain james
[FW1-ike-profile-james]proposal 1
[FW1-ike-profile-james]match remote identity address 202.2.100.2 255.255.255.252
[FW1-ike-profile-james]exchange-mode aggressive
[FW1-ike-profile-james]quit
[FW1]ipsec transform-set james
[FW1-ipsec-transform-set-james]protocol esp
[FW1-ipsec-transform-set-james]encapsulation-mode tunnel
[FW1-ipsec-transform-set-james]esp authentication-algorithm md5
[FW1-ipsec-transform-set-james]esp encryption-algorithm des-cbc
[FW1-ipsec-transform-set-james]quit
[FW1]ipsec policy james 1 isakmp
[FW1-ipsec-policy-isakmp-james-1]security acl 3000
[FW1-ipsec-policy-isakmp-james-1]transform-set james
[FW1-ipsec-policy-isakmp-james-1]ike-profile james
[FW1-ipsec-policy-isakmp-james-1]remote-address 202.2.100.2
[FW1-ipsec-policy-isakmp-james-1]quit
[FW1]int gi 1/0/2
[FW1-GigabitEthernet1/0/2]ipsec apply policy james
[FW1-GigabitEthernet1/0/2]quit
FW2：
System View: return to User View with Ctrl+Z.
[H3C]sysname FW2
[FW2]int gi 1/0/3
[FW2-GigabitEthernet1/0/3]ip address 172.16.1.1 24
[FW2-GigabitEthernet1/0/3]quit
[FW2]int gi 1/0/2
[FW2-GigabitEthernet1/0/2]des
[FW2-GigabitEthernet1/0/2]ip address 202.2.100.2 30
[FW2-GigabitEthernet1/0/2]quit
[FW2]ip route-static 0.0.0.0 0.0.0.0 202.2.100.1
[FW2]security-zone name Untrust
[FW2-security-zone-Untrust]import interface GigabitEthernet 1/0/2
[FW2-security-zone-Untrust]quit
[FW2]security-zone name Trust
[FW2-security-zone-Trust]import interface GigabitEthernet 1/0/3
[FW2-security-zone-Trust]quit
[FW2]zone-pair security source trust destination untrust
[FW2-zone-pair-security-Trust-Untrust]packet-filter 2001
[FW2-zone-pair-security-Trust-Untrust]quit
[FW2]
[FW2]zone-pair security source untrust destination trust
[FW2-zone-pair-security-Untrust-Trust]packet-filter 2001
[FW2-zone-pair-security-Untrust-Trust]quit
[FW2]
[FW2]zone-pair security source trust destination local
[FW2-zone-pair-security-Trust-Local]packet-filter 2001
[FW2-zone-pair-security-Trust-Local]quit
[FW2]
[FW2]zone-pair security source local destination trust
[FW2-zone-pair-security-Local-Trust]packet-filter 2001
[FW2-zone-pair-security-Local-Trust]quit
[FW2]
[FW2]zone-pair security source untrust destination local
[FW2-zone-pair-security-Untrust-Local]packet-filter 2001
[FW2-zone-pair-security-Untrust-Local]quit
[FW2]
[FW2]zone-pair security source local destination untrust
[FW2-zone-pair-security-Local-Untrust]packet-filter 2001
[FW2-zone-pair-security-Local-Untrust]quit
FW2 IPSEC+IKE野蛮模式关键配置点：
[FW2]acl advanced 3000
[FW2-acl-ipv4-adv-3000]rule 0 permit ip source 172.16.1.0 0.0.0.255 destination 192.168.1.0 0.0.0.255
[FW2-acl-ipv4-adv-3000]quit
[FW2]ike identity fqdn fw2
[FW2]ike proposal 1
[FW2-ike-proposal-1]quit
[FW2]ike keychain james
[FW2-ike-keychain-james]pre-shared-key hostname fw1 key simple james
[FW2-ike-keychain-james]quit
[FW2]ike profile james
[FW2-ike-profile-james]keychain james
[FW2-ike-profile-james]proposal 1
[FW2-ike-profile-james]match remote identity fqdn fw1
[FW2-ike-profile-james]exchange-mode aggressive
[FW2-ike-profile-james]quit
[FW2]ipsec transform-set james
[FW2-ipsec-transform-set-james]protocol esp
[FW2-ipsec-transform-set-james]encapsulation-mode tunnel
[FW2-ipsec-transform-set-james]esp authentication-algorithm md5
[FW2-ipsec-transform-set-james]esp encryption-algorithm des-cbc
[FW2-ipsec-transform-set-james]quit
[FW2]ipsec policy-template james 1
[FW2-ipsec-policy-template-james-1]security acl 3000
[FW2-ipsec-policy-template-james-1]transform-set james
[FW2-ipsec-policy-template-james-1]ike-profile james
[FW2-ipsec-policy-template-james-1]quit
[FW2]ipsec policy james 1 isakmp template james
[FW2]int gi 1/0/2
[FW2-GigabitEthernet1/0/2]ipsec apply policy james
[FW2-GigabitEthernet1/0/2]quit
测试：
物理机都填写IP地址：
PC之间可以相互PING通：
查看FW1的IPSEC显示信息：
查看FW1出接口配置及获取到的IP地址：
查看ISP DHCP分配出去的地址：
查看FW2的IPSEC显示信息：
- 2021-06-30回答
- 评论(0)
- 举报
-
(0)
暂无评论
编辑答案
亲~登录后才可以操作哦!
确定你的邮箱还未认证，请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
- 1. 您举报的内容是什么？（请在邮件中列出您举报的内容和链接地址）
- 2. 您是谁？（身份证明材料，可以是身份证或护照等证件）
- 3. 是哪家企业？（营业执照，单位登记证明等证件）
- 4. 您与该企业的关系是？（您是企业法人或被授权人，需提供企业委托授权书）
抄袭了我的内容
×
原文链接或出处
诽谤我
×
- 1. 您举报的内容以及侵犯了您什么权益？（请在邮件中列出您举报的内容、链接地址，并给出简短的说明）
- 2. 您是谁？（身份证明材料，可以是身份证或护照等证件）
对根叔社区有害的内容
×
不规范转载
×
举报说明
暂无评论