华三路由器

您好，请知：

可以使用mp来实现，以下是配置举例：

2.12  MP典型配置举例

2.12.1  通过将物理接口直接绑定到VT接口方式进行MP捆绑配置举例

1. 组网需求

设备Router A和Router B的Serial2/1/1和Serial2/1/0分别对应连接。要求通过将物理接口直接绑定到VT接口方式进行MP捆绑。

2. 组网图

图2-2 通过将物理接口直接绑定到VT接口方式进行MP捆绑组网图

‌

3. 配置步骤

(1)     配置Router A

# 创建虚拟模板接口，配置相应的IP地址。

<RouterA> system-view

[RouterA] interface virtual-template 1

[RouterA-Virtual-Template1] ip address 8.1.1.1 24

[RouterA-Virtual-Template1] quit

# 配置串口Serial2/1/1。

[RouterA] interface serial 2/1/1

[RouterA-Serial2/1/1] link-protocol ppp

[RouterA-Serial2/1/1] ppp mp virtual-template 1

[RouterA-Serial2/1/1] quit

# 配置串口Serial2/1/0。

[RouterA] interface serial 2/1/0

[RouterA-Serial2/1/0] link-protocol ppp

[RouterA-Serial2/1/0] ppp mp virtual-template 1

[RouterA-Serial2/1/0] quit

(2)     配置Router B

# 创建虚拟模板接口，配置相应的IP地址。

<RouterB> system-view

[RouterB] interface virtual-template 1

[RouterB-Virtual-Template1] ip address 8.1.1.2 24

[RouterB-Virtual-Template1] quit

# 配置串口Serial2/1/1。

[RouterB] interface serial 2/1/1

[RouterB-Serial2/1/1] link-protocol ppp

[RouterB-Serial2/1/1] ppp mp virtual-template 1

[RouterB-Serial2/1/1] quit

# 配置串口Serial2/1/0。

[RouterB] interface serial 2/1/0

[RouterB-Serial2/1/0] link-protocol ppp

[RouterB-Serial2/1/0] ppp mp virtual-template 1

[RouterB-Serial2/1/0] quit

4. 验证配置

(1)     在Router A上查看绑定结果

# 查看MP的相关信息。

[RouterA] display ppp mp

Template: Virtual-Template1

max-bind: 16, fragment: enabled, min-fragment: 128

  Master link: Virtual-Access0, Active members: 2, Bundle RouterB

  Peer's endPoint descriptor: RouterB

  Sequence format: long (rcv)/long (sent)

  Bundle Up Time: 2013/01/10  07:13:10:723

  0 lost fragments, 0 reordered, 0 unassigned, 0 interleaved

  Sequence: 0 (rcv)/0 (sent)

  Active member channels: 2 members

        Serial2/1/1               Up-Time:2013/01/10  07:13:10:724

        Serial2/1/0               Up-Time:2013/01/10  07:13:11:945

# 查看VA状态。

[RouterA] display interface virtual-access

Virtual-Access0

Current state: UP

Line protocol state: UP

Description: Virtual-Access0 Interface

Bandwidth: 128kbps

Maximum transmission unit: 1500

Hold timer: 10 seconds,retry times: 5

Internet address: 8.1.1.1/24 (primary)

Link layer protocol: PPP

LCP: opened, MP: opened, IPCP: opened

Physical: MP, baudrate: 128000 bps

Main interface: Virtual-Template1

Output queue - Urgent queuing: Size/Length/Discards 0/1024/0

Output queue - Protocol queuing: Size/Length/Discards 0/500/0

Output queue - FIFO queuing: Size/Length/Discards 0/75/0

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Input: 2 packets, 80 bytes, 0 drops

Output: 2 packets, 24 bytes, 0 drops

(2)     在Router B上ping对端IP地址8.1.1.1

[RouterB] ping 8.1.1.1

Ping 8.1.1.1 (8.1.1.1): 56 data bytes, press CTRL_C to break

56 bytes from 8.1.1.1: icmp_seq=0 ttl=255 time=4.000 ms

56 bytes from 8.1.1.1: icmp_seq=1 ttl=255 time=0.000 ms

56 bytes from 8.1.1.1: icmp_seq=2 ttl=255 time=0.000 ms

56 bytes from 8.1.1.1: icmp_seq=3 ttl=255 time=0.000 ms

56 bytes from 8.1.1.1: icmp_seq=4 ttl=255 time=1.000 ms

--- Ping statistics for 8.1.1.1 ---

5 packet(s) transmitted, 5 packet(s) received, 0.0% packet loss

round-trip min/avg/max/std-dev = 0.000/1.000/4.000/1.549 ms

2.12.2  通过按用户名找VT方式进行MP捆绑配置举例

1. 组网需求

设备Router A和Router B的Serial2/1/1和Serial2/1/0分别对应连接。要求通过按用户名找VT方式进行MP捆绑。

2. 组网图

图2-3 通过按用户名找VT方式进行MP捆绑组网图

‌

3. 配置步骤

(1)     配置Router A

# 配置对端设备Router B在Router A上的用户名和密码。

<RouterA> system-view

[RouterA] local-user usera class network

[RouterA-luser-network-usera] password simple 123456TESTplat&!

[RouterA-luser-network-usera] service-type ppp

[RouterA-luser-network-usera] quit

# 指定用户对应的VT。

[RouterA] ppp mp user usera bind virtual-template 1

# 创建VT，配置相应的IP地址。

[RouterA] interface virtual-template 1

[RouterA-Virtual-Template1] ip address 8.1.1.1 24

[RouterA-Virtual-Template1] ppp mp binding-mode authentication

[RouterA-Virtual-Template1] quit

# 配置串口Serial2/1/1。

[RouterA] interface serial 2/1/1

[RouterA-Serial2/1/1] link-protocol ppp

[RouterA-Serial2/1/1] ppp authentication-mode pap

[RouterA-Serial2/1/1] ppp pap local-user userb password simple 123456TESTplat&!

[RouterA-Serial2/1/1] ppp mp

[RouterA-Serial2/1/1] quit

# 配置串口Serial2/1/0。

[RouterA] interface serial 2/1/0

[RouterA-Serial2/1/0] link-protocol ppp

[RouterA-Serial2/1/0] ppp authentication-mode pap

[RouterA-Serial2/1/0] ppp pap local-user userb password simple 123456TESTplat&!

[RouterA-Serial2/1/0] ppp mp

[RouterA-Serial2/1/0] quit

(2)     配置Router B

# 配置对端设备Router A在Router B上的用户名和密码。

<RouterB> system-view

[RouterB] local-user userb class network

[RouterB-luser-network-userb] password simple 123456TESTplat&!

[RouterB-luser-network-userb] service-type ppp

[RouterB-luser-network-userb] quit

# 指定用户对应的VT。

[RouterB] ppp mp user userb bind virtual-template 1

# 创建VT，配置相应的IP地址。

[RouterB] interface virtual-template 1

[RouterB-Virtual-Template1] ip address 8.1.1.2 24

[RouterB-Virtual-Template1] ppp mp binding-mode authentication

[RouterB-Virtual-Template1] quit

# 配置串口Serial2/1/1。

[RouterB] interface serial 2/1/1

[RouterB-Serial2/1/1] link-protocol ppp

[RouterB-Serial2/1/1] ppp authentication-mode pap

[RouterB-Serial2/1/1] ppp pap local-user usera password simple 123456TESTplat&!

[RouterB-Serial2/1/1] ppp mp

[RouterB-Serial2/1/1] quit

# 配置串口Serial2/1/0。

[RouterB] interface serial 2/1/0

[RouterB-Serial2/1/0] link-protocol ppp

[RouterB-Serial2/1/0] ppp authentication-mode pap

[RouterB-Serial2/1/0] ppp pap local-user usera password simple 123456TESTplat&!

[RouterB-Serial2/1/0] ppp mp

[RouterB-Serial2/1/0] quit

4. 验证配置

(1)     在Router A上查看绑定效果

# 查看MP的相关信息。

[RouterA] display ppp mp

Template: Virtual-Template1

max-bind: 16, fragment: enabled, min-fragment: 128

  Master link: Virtual-Access0, Active members: 2, Bundle usera

  Peer's endPoint descriptor: RouterB

  Sequence format: long (rcv)/long (sent)

  Bundle Up Time: 2013/01/10  08:02:34:881

  0 lost fragments, 0 reordered, 0 unassigned, 0 interleaved

  Sequence: 0 (rcv)/0 (sent)

  Active member channels: 2 members

        Serial2/1/1               Up-Time:2013/01/10  08:02:34:881

        Serial2/1/0               Up-Time:2013/01/10  08:06:26:634

(2)     在Router B上查看绑定效果

# 查看MP的相关信息。

[RouterB] display ppp mp

Template: Virtual-Template1

max-bind: 16, fragment: enabled, min-fragment: 128

  Master link: Virtual-Access0, Active members: 2, Bundle userb

  Peer's endPoint descriptor: RouterA

  Sequence format: long (rcv)/long (sent)

  Bundle Up Time: 2013/01/10  12:31:13:391

  0 lost fragments, 0 reordered, 0 unassigned, 0 interleaved

  Sequence: 0 (rcv)/0 (sent)

  Active member channels: 2 members

        Serial2/1/1               Up-Time:2013/01/10  12:31:13:392

        Serial2/1/0               Up-Time:2013/01/10  12:35:05:892

# 查看VA状态。

[RouterB] display interface virtual-access

Virtual-Access2

Current state: UP

Line protocol state: UP

Description: Virtual-Access0 Interface

Bandwidth: 64kbps

Maximum transmission unit: 1500

Hold timer: 10 seconds，retry times: 5

Internet address: 8.1.1.2/24 (primary)

Link layer protocol: PPP

LCP: opened, MP: opened, IPCP: opened

Physical: MP, baudrate: 64000 bps

Main interface: Virtual-Template1

Output queue - Urgent queuing: Size/Length/Discards 0/1024/0

Output queue - Protocol queuing: Size/Length/Discards 0/500/0

Output queue - FIFO queuing: Size/Length/Discards 0/75/0

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Input: 2 packets, 80 bytes, 0 drops

Output: 2 packets, 24 bytes, 0 drops

# 在Router B上ping对端IP地址8.1.1.1。

[RouterB] ping 8.1.1.1

Ping 8.1.1.1 (8.1.1.1): 56 data bytes, press CTRL_C to break

56 bytes from 8.1.1.1: icmp_seq=0 ttl=255 time=0.000 ms

56 bytes from 8.1.1.1: icmp_seq=1 ttl=255 time=0.000 ms

56 bytes from 8.1.1.1: icmp_seq=2 ttl=255 time=1.000 ms

56 bytes from 8.1.1.1: icmp_seq=3 ttl=255 time=1.000 ms

56 bytes from 8.1.1.1: icmp_seq=4 ttl=255 time=0.000 ms

--- Ping statistics for 8.1.1.1 ---

5 packet(s) transmitted, 5 packet(s) received, 0.0% packet loss

round-trip min/avg/max/std-dev = 0.000/0.400/1.000/0.490 ms

2.12.3  通过将链路绑定到MP-group接口方式进行MP捆绑配置举例

1. 组网需求

设备Router A和Router B的Serial2/1/1和Serial2/1/0分别对应连接。要求通过将链路绑定到MP-group接口方式进行MP捆绑。

2. 组网图

图2-4 通过将链路绑定到MP-group接口方式进行MP捆绑组网图

‌

3. 配置步骤

(1)     配置Router A

# 创建MP-group接口，配置相应的IP地址。

<RouterA> system-view

[RouterA] interface mp-group 2/0/0

[RouterA-MP-group2/0/0] ip address 1.1.1.1 24

# 配置串口Serial2/1/1。

[RouterA-MP-group2/0/0] quit

[RouterA] interface serial 2/1/1

[RouterA-Serial2/1/1] link-protocol ppp

[RouterA-Serial2/1/1] ppp mp mp-group 2/0/0

[RouterA-Serial2/1/1] shutdown

[RouterA-Serial2/1/1] undo shutdown

[RouterA-Serial2/1/1] quit

# 配置串口Serial2/1/0。

[RouterA] interface serial 2/1/0

[RouterA-Serial2/1/0] link-protocol ppp

[RouterA-Serial2/1/0] ppp mp mp-group 2/0/0

[RouterA-Serial2/1/0] shutdown

[RouterA-Serial2/1/0] undo shutdown

[RouterA-Serial2/1/0] quit

(2)     配置Router B

# 创建MP-group接口，配置相应的IP地址。

[RouterB] interface mp-group 2/0/0

[RouterB-Mp-group2/0/0] ip address 1.1.1.2 24

[RouterB-Mp-group2/0/0] quit

# 配置串口Serial2/1/1。

[RouterB] interface serial 2/1/1

[RouterB-Serial2/1/1] link-protocol ppp

 [RouterB-Serial2/1/1] ppp mp mp-group 2/0/0

[RouterB-Serial2/1/1] shutdown

[RouterB-Serial2/1/1] undo shutdown

[RouterB-Serial2/1/1] quit

# 配置串口Serial2/1/0。

[RouterB] interface serial 2/1/0

[RouterB-Serial2/1/0] link-protocol ppp

[RouterB-Serial2/1/0] ppp mp mp-group 2/0/0

[RouterB-Serial2/1/0] shutdown

[RouterB-Serial2/1/0] undo shutdown

[RouterB-Serial2/1/0] quit

4. 验证配置

(1)     在Router A上查看绑定效果

# 查看MP的相关信息。

[RouterA] display ppp mp

Template: MP-group2/0/0

max-bind: 16, fragment: enabled, min-fragment: 128

Master link: MP-group2/0/0, Active members: 2, Bundle Multilink

Peer's endPoint descriptor: MP-group2/0/0

Sequence format: short (rcv)/long (sent)

Bundle Up Time: 2012/11/04  09:03:16:612

0 lost fragments, 0 reordered, 0 unassigned, 0 interleaved

Sequence: 0 (rcvd)/0 (sent)

Active member channels: 2 members

      Serial2/1/1               Up-Time:2012/11/04  09:03:16:613

      Serial2/1/0               Up-Time:2012/11/04  09:03:42:945

# 查看MP-group2/0/0接口的相关信息。

[RouterA] display interface mp-group 2/0/0

MP-group2/0/0

Current state: UP

Line protocol state: UP

Description: MP-group2/0/0 Interface

Bandwidth: 2048kbps

Maximum transmission unit: 1500

Hold timer: 10 seconds，retry times: 5

Internet address: 1.1.1.1/24 (primary)

Link layer protocol: PPP

LCP: opened, MP: opened, IPCP: opened

Physical: MP, baudrate: 2048000 bps

Output queue - Urgent queuing: Size/Length/Discards 0/1024/0

Output queue - Protocol queuing: Size/Length/Discards 0/500/0

Output queue - FIFO queuing: Size/Length/Discards 0/75/0

Last link flapping: Never

Last clearing of counters: Never

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Input: 2 packets, 80 bytes, 0 drops

Output: 2 packets, 24 bytes, 0 drops

# 在RouterA上ping对端IP地址。

[RouterA] ping 1.1.1.2

Ping 1.1.1.2 (1.1.1.2): 56 data bytes, press CTRL_C to break

56 bytes from 1.1.1.2: icmp_seq=0 ttl=255 time=4.000 ms

56 bytes from 1.1.1.2: icmp_seq=1 ttl=255 time=1.000 ms

56 bytes from 1.1.1.2: icmp_seq=2 ttl=255 time=0.000 ms

56 bytes from 1.1.1.2: icmp_seq=3 ttl=255 time=7.000 ms

56 bytes from 1.1.1.2: icmp_seq=4 ttl=255 time=1.000 ms

--- Ping statistics for 1.1.1.2 ---

5 packet(s) transmitted, 5 packet(s) received, 0.0% packet loss

round-trip min/avg/max/std-dev = 0.000/2.600/7.000/2.577 ms