msr2600-10 我这个款路由器拨号连光猫,200兆的带宽,测速只能到100兆,一直上不去
用自己的电脑,同样的环境下,拨号光猫,测速可以满200兆。
这个是哪里需要设置吗? 谢谢
[H3C-GigabitEthernet0/0]display interface Dialer 10
Dialer10 current state: UP Line protocol current state: UP Description: Dialer10 Interface The Maximum Transmit Unit is 1472, Hold timer is 10(sec) Internet Address is negotiated, 106.122.214.123/32 Link layer protocol is PPP LCP initial Physical is Dialer, baudrate: 64000 bps Output queue : (Urgent queuing : Length) 100 Output queue : (Protocol queuing : Length) 500 Output queue : (FIFO queuing : Length) 75 Last clearing of counters: Never Last 300 seconds input rate: 536164 bytes/sec, 4289312 bits/sec, 691 packets/sec Last 300 seconds output rate: 276864 bytes/sec, 2214912 bits/sec, 588 packets/sec 914742204 packets input, 625233917793 bytes, 0 drops 585755945 packets output, 92793894902 bytes, 698 drops Bound to : Dialer10:0 Dialer10:0 current state: UP Line protocol current state: UP Internet protocol processing : disabled Link layer protocol is PPP Primary DNS address is 218.85.152.99,Secondary DNS address is 218.85.157.99 LCP opened, IPCP opened Physical is PPPOE, baudrate: 1000000000 bps Output queue : (Urgent queuing : Size/Length/Discards) 0/100/0 Output queue : (Protocol queuing : Size/Length/Discards) 0/500/0 Output queue : (FIFO queuing : Size/Length/Discards) 0/75/0 Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec 194802 packets input, 159912966 bytes, 0 drops 165119 packets output, 80982465 bytes, 0 drops
[H3C]display interface GigabitEthernet 0/0
GigabitEthernet0/0 current state: UP Line protocol current state: UP Description: GigabitEthernet0/0 Interface The Maximum Transmit Unit is 1500 Internet protocol processing : disabled IP Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 600b-0318-ebcb IPv6 Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 600b-0318-ebcb Media type is twisted pair, loopback not set, promiscuous mode not set 1000Mb/s, Full-duplex, link type is autonegotiation Output flow-control is disabled, input flow-control is disabled Output queue : (Urgent queuing : Size/Length/Discards) 0/100/0 Output queue : (Protocol queuing : Size/Length/Discards) 0/500/0 Output queue : (FIFO queuing : Size/Length/Discards) 0/75/0 Last clearing of counters: Never Last 300 seconds input rate 1085485.00 bytes/sec, 8683880 bits/sec, 1249.68 packets/sec Last 300 seconds output rate 432681.18 bytes/sec, 3461449 bits/sec, 989.71 packets/sec Input: 938677793 packets, 2803995078 bytes, 938677793 buffers 23154508 broadcasts, 0 multicasts, 0 pauses 0 errors, 0 runts, 0 giants 0 crc, 0 align errors, 0 overruns 0 dribbles, 0 drops, 0 no buffers Output:586536399 packets, 2649278260 bytes, 586536399 buffers 34 broadcasts, 0 multicasts, 0 pauses 0 errors, 0 underruns, 0 collisions 0 deferred, 0 lost carriers
(0)
可以尝试更换一下光猫对接路由器的网线或者把出接口的tcp mss值调小一些看看 还是不行的话建议400咨询一下。
(0)
光猫对接网线直接连电脑得话拨号可以到200m,tcp mss调多少合适|?能不能给一个命令? 谢谢
光猫对接网线直接连电脑得话拨号可以到200m,tcp mss调多少合适|?能不能给一个命令? 谢谢
先看下端口协商速率是否是千兆。感觉是端口协商速率没有上去
(0)
dis interface bierf
怎么看端口协商速率?用什么命令?
dis interface bierf
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明