WAP722S-HI-FIT 是否支持FAT模式

AP瘦切胖配置案例（Bootrom） 操作风险提示：AP瘦切胖有风险，操作不当或者意外断电会导致设备故障，操作需谨慎。命令行升级需在PC上搭建TFTP Server（推荐用户使用3CDaemon搭建TFTP服务器） 将软件版本下载到设备FLASH内，然后通过命令行加载Bootrom版本，再加载主机软件版本，加载时输入的文件名一定要一致，建议复制黏贴，然后升级过程中避免断电重启操作。 1、先从官网下载WA4300云AP的胖版本，本案例以WA4320H-SI举例 https://www.h3c.com/cn/d_201909/1225207_30005_40.htm 下载压缩包WA4300S-WPT330-E1105-OASIS.zip，解压生成bin文件，把从官网下载的云AP版本文件改成wa4300s-oasis.bin，放到电脑桌面上。 2、电脑通过网线连接到ap的一个网口，电脑网卡设置为：192.168.0.1 255.255.255.0，如下例子打开TFTP服务器，把bin软件版本放到电脑桌面上，TFTP服务器目录指向电脑桌面，然后点击确定。 3、console口上传版本，console口登录方法参考《1.03 设备管理-Console登录方法》 在AP重启的时候按住不停地按Ctrl+B进入设备的bootroom菜单。 Enter your choice(0-9): ystem is starting... Press Ctrl+D to access BASIC-BOOTWARE MENU Booting Normal Extend BootWare.... The Extend BootWare is self-decompressing.........................Done! **************************************************************************** * * * H3C WA4320H-SI BootWare, Version 1.07 * * * **************************************************************************** Copyright (c) 2004-2017 New H3C Technologies Co., Ltd. Compiled Date : Jun 19 2017 CPU Type : ATHEROS AR9531 CPU L1 Cache : 32KB CPU Clock Speed : 650MHz Memory Type : SDRAM Memory Size : 128MB Memory Speed : 450MHz BootWare Size : 512KB Flash Size : 16MB PCB Version : Ver.A BootWare Validating... Press Ctrl+B to enter extended boot menu... BootWare password: Not required. Please press Enter to continue. Password recovery capability is enabled. Note: The current operating device is flash Enter < Storage Device Operation > to select device. 3.1、升级扩展bootrom版本 要求扩展boot必须为7.13。版本文件中可获取.如果当前版本已经为7.13，直接忽略此步骤。 ====================================================== |<1> Boot System | |<2> Enter Serial SubMenu | |<3> Enter Ethernet SubMenu | |<4> File Control | |<5> Restore to Factory Default Configuration | |<6> Skip Current System Configuration | |<7> BootWare Operation Menu | |<8> Clear Super Password | |<9> Storage Device Operation | |<0> Reboot | ============================================================================ Ctrl+C: Display Copyright Ctrl+F: Format File System Enter your choice(0-9): 7 //进入bootware子菜单 =================================================== |Note:the operating device is flash | |<1> Update BootWare By Serial | |<2> Update BootWare By Ethernet | |<0> Exit To Main Menu | ============================================================================ Enter your choice(0-2): 2 //设置更新bootware方式通过网线 ====================================== |<1> Update Full BootWare | |<2> Update Extend BootWare | |<3> Update Basic BootWare | |<4> Modify Ethernet Parameter | |<0> Exit To Main Menu | ============================================================================ Enter your choice(0-4): 4 //修改以太口参数 ==================================================== |Note: "." = Clear field. | | "-" = Go to previous field. | | Ctrl+D = Quit. | ============================================================================ Protocol (FTP or TFTP) :tftp Load File Name :wap712h_art_v5.bin :apwtu41039757_v7.13.btw //bootware版本名称, 如boot版本已经是V7.13了，可忽略本步骤，继续升级bin版本 Target File Name :wap712h_art_v5.bin :apwtu41039757_v7.13.btw Server IP Address :192.168.1.251 192.168.0.1 //电脑ip地址 Local IP Address :192.168.1.2 192.168.0.19 //配置和电脑同网段任意地址 Gateway IP Address :0.0.0.0 ====================================== |<1> Update Full BootWare | |<2> Update Extend BootWare | |<3> Update Basic BootWare | |<4> Modify Ethernet Parameter | |<0> Exit To Main Menu | ============================================================================ Enter your choice(0-4): 1 //更新bootware版本 Loading..........Done! 381952 bytes downloaded! Updating Basic BootWare? [Y/N]Y //手工输入“Y” Updating Basic BootWare..........Done! Updating Extend BootWare? [Y/N]Y //手工输入“Y” Updating Extend BootWare...........Done! 3.2、升级bin版本 升级完扩展boot之后重启设备（可以看到此时扩展boot已经是7.13版本），进扩展boot升级设备版本。 System is starting... Press Ctrl+D to access BASIC-BOOTWARE MENU... Booting Normal Extended BootWare The Extended BootWare is self-decompressing..........................Done. **************************************************************************** * * * H3C WA4320H-SI BootWare, Version 7.13 * * * **************************************************************************** Copyright (c) 2004-2019 New H3C Technologies Co., Ltd. Compiled Date : Jul 31 2019 CPU Type : ATHEROS AR9531 CPU L1 Cache : 32KB CPU Clock Speed : 650MHz Memory Type : SDRAM Memory Size : 128MB Memory Speed : 450MHz BootWare Size : 512KB Flash Size : 16MB PCB Version : Ver.A BootWare Validating... Press Ctrl+B to access EXTENDED-BOOTWARE MENU... Password recovery capability is enabled. Note: The current operating device is flash Enter < Storage Device Operation > to select device. 上传版本文件 ==================================================== |<1> Boot System | |<2> Enter Serial SubMenu | |<3> Enter Ethernet SubMenu | |<4> File Control | |<5> Restore to Factory Default Configuration | |<6> Skip Current System Configuration | |<7> BootWare Operation Menu | |<8> Skip Authentication for Console Login | |<9> Storage Device Operation | |<0> Reboot | ============================================================================ Ctrl+Z: Access EXTENDED ASSISTANT MENU Ctrl+F: Format File System Ctrl+Y: Change AP Mode Enter your choice(0-9): 3 //进入以太口子菜单 ==================================================== |Note:the operating device is flash | |<1> Download Image Program To SDRAM And Run | |<2> Update Main Image File | |<3> Download Files(*.*) | |<4> Modify Ethernet Parameter | |<0> Exit To Main Menu | | | ============================================================================ Enter your choice(0-4): 4 //修改以太口参数 ==================================================== |Note: "." = Clear field. | | "-" = Go to previous field. | | Ctrl+D = Quit. | ============================================================================ Protocol (FTP or TFTP) :tftp Load File Name :apwtu41039757_v7.13.btw :wa4300s-oasis.bin //此处注意修改版本文件名称,为wa4300s-oasis.bin Target File Name :apwtu41039757_v7.13.btw :wa4300s-oasis.bin //此处注意修改版本文件名称,为wa4300s-oasis.bin Server IP Address :192.168.0.1 //电脑ip地址 Local IP Address :192.168.0.19 //配置和电脑同网段任意地址 Subnet Mask :0.0.0.0 Gateway IP Address :0.0.0.0 ==================================================== |Note:the operating device is flash | |<1> Download Image Program To SDRAM And Run | |<2> Update Main Image File | |<3> Download Files(*.*) | |<4> Modify Ethernet Parameter | |<0> Exit To Main Menu | | | ============================================================================ Enter your choice(0-4): 3 //更新版本 Loading..................................................................... ............................................................................ ............................................................................ .................................................Done. 13698048 bytes downloaded! Saving file flash:/wa4300s-oasis.bin ....................................... ............................................................................ ............................................................................ ............................................................................ ...........................................................Done. 切换ap模式 ==================================================== |Note:the operating device is flash | |<1> Download Image Program To SDRAM And Run | |<2> Update Main Image File | |<3> Download Files(*.*) | |<4> Modify Ethernet Parameter | |<0> Exit To Main Menu | | | ============================================================================ Enter your choice(0-4): 0 ==================================================== |<1> Boot System | |<2> Enter Serial SubMenu | |<3> Enter Ethernet SubMenu | |<4> File Control | |<5> Restore to Factory Default Configuration | |<6> Skip Current System Configuration | |<7> BootWare Operation Menu | |<8> Skip Authentication for Console Login | |<9> Storage Device Operation | |<0> Reboot | ============================================================================ Ctrl+Z: Access EXTENDED ASSISTANT MENU Ctrl+F: Format File System Ctrl+Y: Change AP Mode Enter your choice(0-9): Please select the new mode Current mode is Fit ============================================================================ |NO. Mode | |1 Oasis Mode | |2 Fit Mode | |0 Exit | ============================================================================ Enter your choice(0-2):1 //切换为云模式 This operation takes several minutes.Please wait... Changed to Oasis mode successfully! Please reboot the system now! 切换完成后重启设备 ==================================================== |<1> Boot System | |<2> Enter Serial SubMenu | |<3> Enter Ethernet SubMenu | |<4> File Control | |<5> Restore to Factory Default Configuration | |<6> Skip Current System Configuration | |<7> BootWare Operation Menu | |<8> Skip Authentication for Console Login | |<9> Storage Device Operation | |<0> Reboot | ============================================================================ Ctrl+Z: Access EXTENDED ASSISTANT MENU Ctrl+F: Format File System Ctrl+Y: Change AP Mode Enter your choice(0-9): 0 //重启 System is starting... Press Ctrl+D to access BASIC-BOOTWARE MENU... Booting Normal Extended BootWare The Extended BootWare is self-decompressing..........................Done. **************************************************************************** * * * H3C WA4320H-SI BootWare, Version 7.13 * * * **************************************************************************** Copyright (c) 2004-2019 New H3C Technologies Co., Ltd. Compiled Date : Jul 31 2019 CPU Type : ATHEROS AR9531 CPU L1 Cache : 32KB CPU Clock Speed : 650MHz Memory Type : SDRAM Memory Size : 128MB Memory Speed : 450MHz BootWare Size : 512KB Flash Size : 16MB PCB Version : Ver.A BootWare Validating... Press Ctrl+B to access EXTENDED-BOOTWARE MENU... starting... 配置关键点： 1、第三步选择Download Files，否则会出现报错； 2、需要上传版本文件之后再切换ap模式； 3、刷完版本之后只能通过web管理； 4、云ap里，只有WAP712C-LI 型号，是要用7.17的boot的, 该版本适配的其他款型均用7.13的boot； 5、严格按照案例中操作步骤执行，关键注意先上传版本文件之后再切换ap模式； 6、把从官网下载的云AP版本文件改成wa4300s-oasis.bin； 7、操作完成后设备启动会停留在starting…阶段，实际可能已经完成，如果能搜索到SSID为H3C_XXXXXX（mac后6位）的SSID说明已经转换完成并启动。 云AP是Fat AP。初次使用云AP，给云AP上电后，云AP会默认开启4个无线服务： l 其中一个称之为管理WIFI，也称内部WIFI，SSID为H3C_XXXXXX，XXXXXX为设备mac地址后六位。管理WIFI供商铺内部员工管理使用，一般在2.4G频段工作，当设备未连接到绿洲时，通过连接管理WIFI在浏览器输入10.40.94.1或myap.h3c.com访问本地web页面可进行本设备下的无线服务管理配置，一旦连接上绿洲，将只能通过绿洲平台进行统一的无线服务配置管理。

兄弟，你这文章的格式全乱了

轻轻松松配无线：https://zhiliao.h3c.com/topic/huati/1249