请问大佬H3C s5560s-28p-si 交换机可以IRF堆叠吗?只有四个SFP端口
(0)
最佳答案
可以的
https://www.h3c.com/cn/d_201908/1222161_30005_0.htm#_Toc17386154
在本系列交换机上,不同机型支持绑定IRF端口的物理端口有所不同,配置前请按照如下原则确认:
· 设备有10GE接口时,仅10GE接口支持做IRF物理端口,且端口必须工作在10G速率下;没有10GE接口时,1GE接口支持做IRF物理端口,且端口必须工作在1G速率下。
· 同一IRF端口绑定的多个物理端口必须属于同一组。同一组中的物理端口可以绑定到不同的IRF端口。在Probe视图下执行debug port mapping命令,如果端口的Unit值相同,则表示端口属于同一组。
关于各机型具体支持的IRF物理端口及其分组限制、IRF物理端口支持的光模块/线缆,请参考安装手册。
(0)
请问,我两台H3C s5560s-28p-si设备 配置IRF后SW2没有自动重启,手动重启后SW2交换机名称没有变,查看配置没有成功,而且SW2交换机接口指示灯不亮,SW1接口指示灯时亮的。请问可能时什么原因呢?
SW1配置:irf member 1 priority 1[s5560-01]irf member 1 priority 32[s5560-01]interface GigabitEthernet 1/0/27[s5560-01-GigabitEthernet1/0/27]interface GigabitEthernet 1/0/28[s5560-01-GigabitEthernet1/0/28]shutdown[s5560-01-GigabitEthernet1/0/28]qu[s5560-01-irf-port1/1]port group interface GigabitEthernet 1/0/27You must perform the following tasks for a successful IRF setup:Save the configuration after completing IRF configuration.Execute the "irf-port-configuration active" co m mand to activate the IRF ports.[s5560-01-irf-port1/1]port group interface GigabitEthernet 1/0/28[s5560-01-irf-port1/1]qu[s5560-01]interface GigabitEthernet 1/0/27[s5560-01-GigabitEthernet1/0/27]undo shutdown[s5560-01-GigabitEthernet1/0/27]interface GigabitEthernet 1/0/28[s5560-01-GigabitEthernet1/0/28]undo shutdown[s5560-01-GigabitEthernet1/0/28]qu[s5560-01]irf-port-configuration active[s5560-01]saveThe current configuration will be written to the device. Are you sure? [Y/N]:yplease input the file name(*.cfg)[flash:/startup.cfg]flash:/startup.cfg exists,overwrite?[Y/N]:y(To leave the existing filename unchanged, press the enter key):Validating file. Please wait.….Saved the current configuration to mainboard device successfully.[s5560-01]qu SW2配置:irf member 2 priority 1[H3C]interface GigabitEthernet 2/0/27[H3C-GigabitEthernet2/0/27]shutdown[H3C-GigabitEthernet2/0/27]interface GigabitEthernet 2/0/28[H3C-GigabitEthernet2/0/28]shutdown[H3C-GigabitEthernet2/0/28]qu[H3CJI1F-pot 27e[H3C-irf-port2/2]port group interface GigabitEthernet 2/0/27You must perform the following tasks for a successful IRF setup:Save the configuration after completing IRF configuration.Execute the "irf-port-configuration active" command to activate the IRF ports.[H3C-if-port2/2]port group interface GigabitEthernet 2/0/28[H3C-irf-port2/2ldis th ~wr .irf-port 2/2port group interface GigabitEthernet2/0/27 mode normalport group interface GigabitEthernet2/0/28 mode normal[H3C-irf-port2/2lau[H3C]interface GigabitEthernet 2/0/27[H3C-GigabitEthernet2/0/27]undo shutdown[H3C-GigabitEthernet2/0/27]interface GigabitEthernet 2/0/28[H3C-GigabitEthernet2/0/28lundo shut .[H3C-GigabitEthernet2/0/28]qu[H3C]saveThe current configuration will be written to the device. Are you sure? [Y/N]:yPlease input the file na me(*.cfg)[flash:/startup.cfgl .…(To leave the existing filename unchanged, press the enter key):flash:/startup.cfg exists, overwrite?[Y/N]:yValidating file. Please wait…Saved the current configuration to mainboard device successfully.[H3C]irf-port-configuration active[H3C]save[H3C]qu
麻烦您给看下什么原因,两台交换机有一台交换机的接口指示灯不亮,堆叠也不成功。同样的方法另外两台5500v2 都可以成功。
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明
那有一端的灯是亮的,应该不是模块的问题了