3.3  保存交换机配置

[H3C]save force      

3.4  登录AC命令行，配置国家码cn

#需要配置国家码为cn，如选择其他区域可能会造成部分功能无法使用

Press ENTER to get started.

 Please set your country/region code.

 Input ? to get the country code list, or input q to log out.

 Cn

3.5  AC修改地址、配置静态路由、创建vlan2

#进入系统视图

<H3C>system-view

#修改AC的地址为192.168.1.1 255.255.255.0

[H3C]interface Vlan-interface 1

[H3C-Vlan-interface1]ip address 192.168.1.1 255.255.255.0

[H3C-Vlan-interface1]quit

#配置静态路由

[H3C]ip route-static 192.168.2.0 255.255.255.0 192.168.1.2

#创建vlan 2

[H3C]vlan 2

[H3C-vlan2]quit

3.6  配置无线加密服务模板

# 配置创建无线服务模板，ssid为test

[H3C] wlan service-template 1

[H3C-wlan-st-1] ssid test

# 配置AKM为PSK，配置PSK密钥，使用明文的字符串12345678作为共享密钥

[H3C-wlan-st-1] akm mode psk

[H3C-wlan-st-1] preshared-key pass-phrase simple 12345678

# 配置CCMP为加密套件，配置WPA2为安全信息元素

[H3C-wlan-st-1] cipher-suite ccmp

[H3C-wlan-st-1] security-ie rsn

# 加入vlan2

[H3C-wlan-st-1] vlan 2

# 使能无线服务模板

[H3C-wlan-st-1] service-template enable

[H3C-wlan-st-1] quit

3.7  配置AP模板，并绑定无线加密服务模板

#创建型号为wap712c的AP模板，配置AP对应的序列号。有几个AP就需要配置几个AP模板。在两个射频上绑定服务模板。WAP712C为双射频AP，有两个射频口。如若是单射频AP，只需配置radio 1 即可

[H3C]wlan ap ap1 model WAP712c

[H3C-wlan-ap-ap1]serial-id  219801**********1454 

[H3C-wlan-ap-ap1]radio 1 

[H3C-wlan-ap-ap1-radio-1]service-template  1

[H3C-wlan-ap-ap1-radio-1]quit

[H3C-wlan-ap-ap1]radio  2

[H3C-wlan-ap-ap1-radio-2]service-template  1

[H3C-wlan-ap-ap1-radio-2]quit

[H3C-wlan-ap-ap1]quit

[H3C]wlan ap ap2 model WAP712c

[H3C-wlan-ap-ap2]serial-id  219801**********1442 

[H3C-wlan-ap-ap2]radio 1 

[H3C-wlan-ap-ap2-radio-1]service-template  1

[H3C-wlan-ap-ap2-radio-1]quit

[H3C-wlan-ap-ap2]radio  2

[H3C-wlan-ap-ap2-radio-2]service-template  1

[H3C-wlan-ap-ap2-radio-2]quit

[H3C-wlan-ap-ap2]quit

#待大概1~5分钟左右，可以使用display wlan ap all查看。如若有状态为R/M的AP，说明AP正常上线

<H3C>display wlan ap all

 Total Number of APs configured           : 2

 Total Number of configured APs connected : 2

 Total Number of auto APs connected       : 0

 Total Number of APs connected            : 0

 Maximum AP capacity                      : 32

 Remaining AP capacity                    : 32

                                  AP Profiles

 State : I = Idle,   J = Join, JA = JoinAck,   IL = ImageLoad

         C = Config, R = Run,  KU = KeyUpdate, KC = KeyCfm

         M = Master, B = Backup

--------------------------------------------------------------------------------

 AP Name                          State Model              Serial-ID

--------------------------------------------------------------------------------

 ap1                              R/M     WAP712C            219801**********1454

ap2                              R/M     WAP712C            219801**********1442

-------------------------------------------------------------------------------

3.8  保存配置

[H3C]save force