MSR800路由器SFP设置

sfp就是光口，你直接interfa x进入光口，然后和普通拨号设置是一样的

跟端口类型没关系，参考：

ADSL/G.SHDSL接口配置  WEB

利用ADSL Modem将局域网接入Internet        命令行 

您好，请知：

纯光口不需要单独开启的，接入光模块和接线就好。

如果是光电复用口，默认在电口，需要切换为光口，参考命令如下：

int gi 1/0/25

combo enable filber

quit

以下是路由器作为客户端进行PPPOE拨号的案例：

2.4.2  PPPoE Client典型配置举例

1. 组网需求

Router A和Router B之间通过各自的Ethernet1/1接口相连，要求Router A用PAP/CHAP方式认证Router B。

2. 组网图

图2-4 PPPoE Client典型配置组网图

3. 配置步骤

(1)     方案一：PAP认证

·     配置Router A作为PPPoE Server

# 增加一个PPPoE用户。

<RouterA> system-view

[RouterA] local-user user2

[RouterA-luser-user2] password simple hello

[RouterA-luser-user2] service-type ppp

[RouterA-luser-user2] quit

# 配置虚拟模板参数。

[RouterA] interface virtual-template 1

[RouterA-Virtual-Template1] ppp authentication-mode pap

[RouterA-Virtual-Template1] ip address 1.1.1.1 255.0.0.0

[RouterA-Virtual-Template1] remote address 1.1.1.2

[RouterA-Virtual-Template1] quit

# 配置PPPoE Server。

[RouterA] interface ethernet 1/1

[RouterA-Ethernet1/1] pppoe-server bind virtual-template 1

·     配置Router B作为PPPoE Client

<RouterB> system-view

[RouterB] dialer-rule 1 ip permit

[RouterB] interface dialer 1

[RouterB-Dialer1] dialer user user2

[RouterB-Dialer1] dialer-group 1

[RouterB-Dialer1] dialer bundle 1

[RouterB-Dialer1] ip address ppp-negotiate

[RouterB-Dialer1] ppp pap local-user user2 password simple hello

[RouterB-Dialer1] quit

# 配置PPPoE会话。

[RouterB] interface ethernet 1/1

[RouterB-Ethernet1/1] pppoe-client dial-bundle-number 1

(2)     方案二：CHAP认证

·     配置Router A作为PPPoE Server

# 增加一个PPPoE用户。

<RouterA> system-view

[RouterA] local-user user2

[RouterA-luser-user2] password simple hello

[RouterA-luser-user2] service-type ppp

[RouterA-luser-user2] quit

# 配置虚拟模板参数。

[RouterA] interface virtual-template 1

[RouterA-Virtual-Template1] ppp authentication-mode chap

[RouterA-Virtual-Template1] ppp chap user user1

[RouterA-Virtual-Template1] ip address 1.1.1.1 255.0.0.0

[RouterA-Virtual-Template1] remote address 1.1.1.2

[RouterA-Virtual-Template1] quit

# 配置PPPoE Server。

[RouterA] interface ethernet 1/1

[RouterA-Ethernet1/1] pppoe-server bind virtual-template 1

·     配置Router B作为PPPoE Client

<RouterB> system-view

[RouterB] dialer-rule 1 ip permit

[RouterB] interface dialer 1

[RouterB-Dialer1] dialer user user2

[RouterB-Dialer1] dialer-group 1

[RouterB-Dialer1] dialer bundle 1

[RouterB-Dialer1] ip address ppp-negotiate

[RouterB-Dialer1] ppp chap user user2

[RouterB-Dialer1] quit

[RouterB] local-user user1

[RouterB-luser-user1] password simple hello

[RouterB-luser-user1] quit

# 配置PPPoE会话。

[RouterB] interface ethernet 1/1

[RouterB-Ethernet1/1] pppoe-client dial-bundle-number 1