H3C F1000-AK1160怎么做端口映射？

1. 确定需要映射的内部服务器的IP地址和端口号；
2. 在F1000-AK1160中创建一个端口映射规则，将公网IP地址和端口号映射到内部服务器的IP地址和端口号；
3. 确认F1000-AK1160的防火墙设置允许公网流量传输到内部服务器；
4. 测试端口映射是否成功，可以使用外部网络连接到公网IP地址和端口号，确认能否访问到内部服务器。

需要注意的是，在没有NAT的情况下，公网IP地址直接暴露在网络中，安全风险较高，需要加强安全措施，如设置访问控制列表、启用端口扫描检测等。

新建一个策略 做目的地址转换

您好，请知：

可以使用nat server将内部服务器映射到外网。

以下是配置举例，请参考：

2.13.3  外网用户通过外网地址访问内网服务器配置举例

1. 组网需求

某公司内部对外提供Web、FTP和SMTP服务，而且提供两台Web服务器。公司内部网址为10.110.0.0/16。其中，内部FTP服务器地址为10.110.10.3/16，内部Web服务器1的IP地址为10.110.10.1/16，内部Web服务器2的IP地址为10.110.10.2/16，内部SMTP服务器IP地址为10.110.10.4/16。公司拥有202.38.1.1至202.38.1.3三个公网IP地址。需要实现如下功能：

·     外部的主机可以访问内部的服务器。

·     选用202.38.1.1作为公司对外提供服务的IP地址，Web服务器2对外采用8080端口。

2. 组网图

图2-5 外网用户通过外网地址访问内网服务器配置组网图

‌

3. 配置步骤

(1)     配置接口IP地址

# 根据组网图中规划的信息，配置各接口的IP地址，具体配置步骤如下。

<Device> system-view

[Device] interface gigabitethernet 1/0/1

[Device-GigabitEthernet1/0/1] ip address 10.110.10.10 16

[Device-GigabitEthernet1/0/1] quit

请参考以上步骤配置其他接口的IP地址，具体配置步骤略。

(2)     将接口加入安全域

# 请根据组网图中规划的信息，将接口加入对应的安全域，具体配置步骤如下。

[Device] security-zone name trust

[Device-security-zone-Trust] import interface gigabitethernet 1/0/1

[Device-security-zone-Trust] quit

[Device] security-zone name untrust

[Device-security-zone-Untrust] import interface gigabitethernet 1/0/2

[Device-security-zone-Untrust] quit

(3)     配置安全策略

# 配置名称为untrust-trust的安全策略，保证Untrust安全域中的Host可以访问Trust安全域中的Server，具体配置步骤如下。

[Device] security-policy ip

[Device-security-policy-ip] rule name untrust-trust

[Device-security-policy-ip-1-untrust-trust] source-zone untrust

[Device-security-policy-ip-1-untrust-trust] destination-zone trust

[Device-security-policy-ip-1-untrust-trust] destination-ip-host 10.110.10.1

[Device-security-policy-ip-1-untrust-trust] destination-ip-host 10.110.10.2

[Device-security-policy-ip-1-untrust-trust] destination-ip-host 10.110.10.3

[Device-security-policy-ip-1-untrust-trust] destination-ip-host 10.110.10.4

[Device-security-policy-ip-1-untrust-trust] action pass

[Device-security-policy-ip-1-untrust-trust] quit

[Device-security-policy-ip] quit

(4)     配置NAT功能

# 配置服务对象组，提供FTP、Web和SMTP服务。

[Device] object-group service service1

[Device-obj-grp-service-service1] service tcp destination eq 21

[Device-obj-grp-service-service1] quit

[Device] object-group service service2

[Device-obj-grp-service-service2] service tcp destination eq 80

[Device-obj-grp-service-service2] quit

[Device] object-group service service3

[Device-obj-grp-service-service3] service tcp destination eq 8080

[Device-obj-grp-service-service3] quit

[Device] object-group service service4

[Device-obj-grp-service-service4] service tcp destination eq 25

[Device-obj-grp-service-service4] quit

# 配置全局NAT规则，允许外网主机访问内网服务器。

[Device] nat global-policy

[Device-nat-global-policy] rule name rule1

[Device-nat-global-policy-rule-rule1] destination-ip host 202.38.1.1

[Device-nat-global-policy-rule-rule1] source-zone untrust

[Device-nat-global-policy-rule-rule1] service service1

[Device-nat-global-policy-rule-rule1] action dnat ip-address 10.110.10.3 local-port 21

[Device-nat-global-policy-rule-rule1] quit

[Device-nat-global-policy] rule name rule2

[Device-nat-global-policy-rule-rule2] destination-ip host 202.38.1.1

[Device-nat-global-policy-rule-rule2] source-zone untrust

[Device-nat-global-policy-rule-rule2] service service2

[Device-nat-global-policy-rule-rule2] action dnat ip-address 10.110.10.1 local-port 80

[Device-nat-global-policy-rule-rule2] quit

[Device-nat-global-policy] rule name rule3

[Device-nat-global-policy-rule-rule3] destination-ip host 202.38.1.1

[Device-nat-global-policy-rule-rule3] source-zone untrust

[Device-nat-global-policy-rule-rule3] service service3

[Device-nat-global-policy-rule-rule3] action dnat ip-address 10.110.10.2 local-port 80

[Device-nat-global-policy-rule-rule3] quit

[Device-nat-global-policy] rule name rule4

[Device-nat-global-policy-rule-rule4] destination-ip host 202.38.1.1

[Device-nat-global-policy-rule-rule4] source-zone untrust

[Device-nat-global-policy-rule-rule4] service service4

[Device-nat-global-policy-rule-rule4] action dnat ip-address 10.110.10.4 local-port 25

[Device-nat-global-policy-rule-rule4] quit

[Device-nat-global-policy] quit

4. 验证配置

# 以上配置完成后，外网Host能够通过NAT地址访问各内网服务器。通过查看如下显示信息，可以验证以上配置成功。

[Device] display nat all

NAT global-policy information:

  Totally 4 NAT global-policy rules.

  Rule name: rule1

    Type                  : nat

    DestIP address        : 202.38.1.1

    Source-zone name      : untrust

    Service object group  : service1

  DNAT action:

      IPv4 address: 10.110.10.3

      Port: 21

    NAT counting : 0

    Config status: Active

  Rule name: rule2

    Type                  : nat

    DestIP address        : 202.38.1.1

    Source-zone name      : untrust

    Destination-zone name : trust

    Service object group  : service2

  DNAT action:

      IPv4 address: 10.110.10.1

      Port: 80

    NAT counting : 0

    Config status: Active

  Rule name: rule3

    Type                  : nat

    DestIP address        : 202.38.1.1

    Source-zone name      : untrust

    Destination-zone name : trust

    Service object group  : service3

  DNAT action:

      IPv4 address: 10.110.10.2

      Port: 80

    NAT counting : 0

    Config status: Active

  Rule name: rule4

    Type                  : nat

    DestIP address        : 202.38.1.1

    Source-zone name      : untrust

    Destination-zone name : trust

    Service object group  : service4

  DNAT action:

      IPv4 address: 10.110.10.4

      Port: 25

    NAT counting : 0

    Config status: Active

NAT logging:

  Log enable          : Disabled

  Flow-begin          : Disabled

  Flow-end            : Disabled

  Flow-active         : Disabled

  Port-block-assign   : Disabled

  Port-block-withdraw : Disabled

  Alarm               : Disabled

  NO-PAT IP usage     : Disabled

NAT mapping behavior:

  Mapping mode : Address and Port-Dependent

  ACL          : ---

  Config status: Active

NAT ALG:

  DNS        : Enabled

  FTP        : Enabled

  H323       : Disabled

  ICMP-ERROR : Enabled

  ILS        : Disabled

  MGCP       : Disabled

  NBT        : Disabled

  PPTP       : Enabled

  RTSP       : Enabled

  RSH        : Disabled

  SCCP       : Disabled

  SCTP       : Disabled

  SIP        : Disabled

  SQLNET     : Disabled

  TFTP       : Disabled

  XDMCP      : Disabled

Static NAT load balancing:     Disabled

NAT link-switch recreate-session: Disabled

NAT configuration-for-new-connection: Disabled

# 通过以下显示命令，可以看到Host访问FTP server时生成NAT会话信息。

[Device] display nat session verbose

Slot 1:

Initiator:

  Source      IP/port: 202.38.1.2/52802

  Destination IP/port: 202.38.1.1/21

  DS-Lite tunnel peer: -

  VPN instance/VLAN ID/Inline ID: -/-/-

  Protocol: TCP(6)

  Inbound interface: GigabitEthernet1/0/2

  Source security zone: Untrust

Responder:

  Source      IP/port: 10.110.10.3/21

  Destination IP/port: 202.38.1.2/52802

  DS-Lite tunnel peer: -

  VPN instance/VLAN ID/Inline ID: -/-/-

  Protocol: TCP(6)

  Inbound interface: GigabitEthernet1/0/1

  Source security zone: Trust

State: TCP_ESTABLISHED

Application: FTP

Rule ID: -/-/-

Rule name:

Start time: 2017-05-21 11:13:39  TTL: 3597s

Initiator->Responder:            7 packets        313 bytes

Responder->Initiator:            6 packets        330 bytes

Total sessions found: 1