问

对接华为交换机

二层转发

2023-06-13提问

0关注
0收藏，2109浏览

奔跑的小马

奔跑的小马六段

粉丝：10人关注：7人

问题描述：

华三万兆7503x对接华为s5700。两台交换都是万兆交换机。但是插的是华三的千兆模块。现在显示灯不亮。我把华三交换机端口强制千兆全双工。华为侧尝试强制千兆，无强制千兆命令。是哪里的原因呀。要做静态聚合。下面配置是已删除强制千兆命令。

华三交换机配置

interface Ten-GigabitEthernet2/3/0/36

port link-mode bridge

description to HQ_SJZ_JR_SW_S5700_48_F20_BG_3

port link-type trunk

undo port trunk permit vlan 1

port trunk permit vlan 2 to 4094

port link-aggregation group 20

interface Ten-GigabitEthernet1/3/0/36

port link-mode bridge

description to HQ_SJZ_JR_SW_S5700_48_F20_BG_3

port link-type trunk

undo port trunk permit vlan 1

port trunk permit vlan 2 to 4094

port link-aggregation group 20

interface Bridge-Aggregation20

description to HQ_SJZ_JR_SW_S5700_48_F20_BG_3

port link-type trunk

undo port trunk permit vlan 1

port trunk permit vlan 2 to 4094

华为交换机

interface Eth-Trunk1

port link-type trunk

undo port trunk allow-pass vlan 1

port trunk allow-pass vlan 2 to 4094

interface XGigabitEthernet0/1/1

eth-trunk 1

interface XGigabitEthernet0/1/2

eth-trunk 1

组网及组网描述：

4 个回答

按时间按赞数

叫我靓仔

叫我靓仔九段

粉丝：160人关注：1人

这种情况，第一步是dis interface xxx

看下接口有没有识别到模块，然后再往下排查

华为知了链接是那个呀，我去华为知了问问

奔跑的小马发表时间：2023-06-13 更多>>

XGigabitEthernet0/1/1 current state : DOWN Line protocol current state : DOWN Description: Switch Port, TPID : 8100(Hex), The Maximum Frame Length is 1600 IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 04bd-70bf-6a50 Current system time: 2023-06-13 13:10:29+08:00 Port Mode: COMMON FIBER Speed : 10000, Loopback: NONE Duplex: FULL, Negotiation: DISABLE Flow-control: DISABLE Last 300 seconds input rate 0 bits/sec, 0 packets/sec Last 300 seconds output rate 0 bits/sec, 0 packets/sec Input peak rate 0 bits/sec, Record time: - Output peak rate 0 bits/sec, Record time: - Input: 0 packets, 0 bytes Unicast: 0, Multicast: 0 Broadcast: 0, Jumbo: 0 Discard: 0, Pause: 0 Total Error: 0 CRC: 0, Giants: 0 Jabbers: 0, Fragments: 0 Runts: 0, DropEvents: 0 Alignments: 0, Symbols: 0 Ignoreds: 0, Frames: 0 Output: 0 packets, 0 bytes Unicast: 0, Multicast: 0 Broadcast: 0, Jumbo: 0 Discard: 0, Pause: 0 Total Error: 0 Collisions: 0, ExcessiveCollisions: 0 Late Collisions: 0, Deferreds: 0 Buffers Purged: 0 Input bandwidth utilization threshold : 90.00% Output bandwidth utilization threshold: 90.00% Input bandwidth utilization : 0% Output bandwidth utilization : 0% [HQ_SJZ_JR_SW_S5700_48_F20_BG_3-XGigabitEthernet0/1/1]

奔跑的小马发表时间：2023-06-13

华为知了链接是那个呀，我去华为知了问问

奔跑的小马发表时间：2023-06-13

zhiliao_KAQOXz

zhiliao_KAQOXz 六段

粉丝：6人关注：0人

首先得确认万兆的这个端口适配千兆模块才行

不然肯定Up不起来的

华为这个应该没有问题

奔跑的小马发表时间：2023-06-13 更多>>

华为这个应该没有问题

奔跑的小马发表时间：2023-06-13

奔跑的小马

奔跑的小马六段

粉丝：10人关注：7人

XGigabitEthernet0/1/1 current state : DOWN
Line protocol current state : DOWN
Description:
Switch Port, TPID : 8100(Hex), The Maximum Frame Length is 1600
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 04bd-70bf-6a50
Current system time: 2023-06-13 13:10:29+08:00
Port Mode: COMMON FIBER
Speed : 10000, Loopback: NONE
Duplex: FULL, Negotiation: DISABLE
Flow-control: DISABLE
Last 300 seconds input rate 0 bits/sec, 0 packets/sec
Last 300 seconds output rate 0 bits/sec, 0 packets/sec
Input peak rate 0 bits/sec, Record time: -
Output peak rate 0 bits/sec, Record time: -
Input: 0 packets, 0 bytes
Unicast: 0, Multicast: 0
Broadcast: 0, Jumbo: 0
Discard: 0, Pause: 0

Total Error: 0
CRC: 0, Giants: 0
Jabbers: 0, Fragments: 0
Runts: 0, DropEvents: 0
Alignments: 0, Symbols: 0
Ignoreds: 0, Frames: 0

Output: 0 packets, 0 bytes
Unicast: 0, Multicast: 0
Broadcast: 0, Jumbo: 0
Discard: 0, Pause: 0

Total Error: 0
Collisions: 0, ExcessiveCollisions: 0
Late Collisions: 0, Deferreds: 0
Buffers Purged: 0

Input bandwidth utilization threshold : 90.00%
Output bandwidth utilization threshold: 90.00%
Input bandwidth utilization : 0%
Output bandwidth utilization : 0%

[HQ_SJZ_JR_SW_S5700_48_F20_BG_3-XGigabitEthernet0/1/1]