ACG1000-X

重启无法正常启动，信息如下：

U-Boot 2011.03 (Release Version: V3.6.1_B609) (Build time: Apr 01 2016 - 15:50:54)

Skipping PCIe port 0 BIST, reset not done. (port not configured)

Skipping PCIe port 1 BIST, reset not done. (port not configured)

BIST check passed.

Warning: Clock descriptor tuple not found in eeprom, using defaults

Warning: Board descriptor tuple not found in eeprom, using defaults

CUST_MC5800 board revision major:1, minor:0, serial #: MC5800

OCTEON CN6880-HAP pass 2.2, Core clock: 1200 MHz, IO clock: 800 MHz, DDR clock: 533 MHz (1066 Mhz DDR)

Base DRAM address used by u-boot: 0x0f800000, size: 0x7fdb80

DRAM: 8 GiB

Now running in RAM - U-Boot at: ffffffffc0000000

Clearing DRAM...... done

NAND:  1024 MiB

Flash: 4 MiB

PCIe: Port 0 is XAUI, skipping.

PCIe: Port 1 link active, 4 lanes, speed gen2

PCI console init succeeded, 1 consoles, 1024 bytes each

Net:   Unknown PHY compatibility "davicom,dm9161"

here get mii link state for mc5800 

octmgmt0, octeth0, octeth1, octeth2, octeth3, octeth4, octeth5, octeth6, octeth7, octeth8

Bus 0: not available  

DTT: Unknown manufacturer id 0xff

DTT:    FAILED INIT

USB:   USB EHCI 1.00

scanning bus for devices... 1 USB Device(s) found

Type the command 'usb start' to scan for USB storage devices.

Bypass is set

CPLD1 3003

CPLD2 4   

Press Ctrl+C to enter menuboot:  0 

Creating 1 MTD partitions on "nand0":

0x000000000000-0x000040000000 : "mtd=0"

UBI: attaching mtd2 to ubi0

UBI: physical eraseblock size:   524288 bytes (512 KiB)

UBI: logical eraseblock size:    520192 bytes

UBI: smallest flash I/O unit:    4096

UBI: sub-page size:              1024

UBI: VID header offset:          1024 (aligned 1024)

UBI: data offset:                4096

UBI error: ubi_io_read: error -77 while reading 520192 bytes from PEB 312:4096, read 520192 bytes

UBI warning: ubi_eba_copy_leb: error -77 while reading data from PEB 312

UBI error: wear_leveling_worker: error -77 while moving PEB 312 to PEB 1709

UBI warning: ubi_ro_mode: switch to read-only mode

UBI error: do_work: work failed with error code -77

UBI: attached mtd2 to ubi0

UBI: MTD device name:            "mtd=0"

UBI: MTD device size:            1024 MiB

UBI: number of good PEBs:        2048

UBI: number of bad PEBs:         0

UBI: max. allowed volumes:       128

UBI: wear-leveling threshold:    4096

UBI: number of internal volumes: 1

UBI: number of user volumes:     1

UBI: available PEBs:             140

UBI: total number of reserved PEBs: 1908

UBI: number of PEBs reserved for bad PEB handling: 20

UBI: max/mean erase counter: 12219/9948

UBIFS: read-only UBI device

UBIFS: recovery needed

UBIFS: recovery deferred

UBIFS: mounted UBI device 0, volume 0, name "rootfs"

UBIFS: mounted read-only

UBIFS: file system size:   974319616 bytes (951484 KiB, 929 MiB, 1873 LEBs)

UBIFS: journal size:       33292288 bytes (32512 KiB, 31 MiB, 64 LEBs)

UBIFS: media format:       w4/r0 (latest is w4/r0)

UBIFS: default compressor: LZO

UBIFS: reserved for root:  5182151 bytes (5060 KiB)

Loading file 'vmlinux.64' to addr 0x20000000 with size 44082896 (0x02a0a6d0)...

UBI: fixable bit-flip detected at PEB 648

UBI: schedule PEB 648 for scrubbing

UBI: fixable bit-flip detected at PEB 648

UBI error: ubi_io_write: read-only mode

UBI error: wear_leveling_worker: error -30 while moving PEB 648 to PEB 1777

UBI error: do_work: work failed with error code -30

Loading vmlinux.64: |..                                      |   5%UBI: fixable bit-flip detected at PEB 1510

UBI: schedule PEB 1510 for scrubbing

UBI: fixable bit-flip detected at PEB 1510

UBI error: ubi_io_write: read-only mode

UBI error: wear_leveling_worker: error -30 while moving PEB 1510 to PEB 1137

UBI error: do_work: work failed with error code -30

Loading vmlinux.64: |...                                     |   8%UBI: fixable bit-flip detected at PEB 394

UBI: schedule PEB 394 for scrubbing

UBI: fixable bit-flip detected at PEB 394

UBI error: ubi_io_write: read-only mode

UBI error: wear_leveling_worker: error -30 while moving PEB 394 to PEB 1460

UBI error: do_work: work failed with error code -30

UBI: fixable bit-flip detected at PEB 262

UBI: schedule PEB 262 for scrubbing

UBI: fixable bit-flip detected at PEB 262

UBI error: ubi_io_write: read-only mode

UBI error: wear_leveling_worker: error -30 while moving PEB 262 to PEB 752

UBI error: do_work: work failed with error code -30

Loading vmlinux.64: |....                                    |  10%UBI: fixable bit-flip detected at PEB 262

UBI: schedule PEB 262 for scrubbing

UBI error: ubi_wl_scrub_peb: PEB 262 not found

UBIFS error (pid 0): try_read_node: cannot read node type 1 from LEB 1619:475720, error -19

UBI: fixable bit-flip detected at PEB 262

UBI: schedule PEB 262 for scrubbing

UBI error: ubi_wl_scrub_peb: PEB 262 not found

UBIFS error (pid 0): ubifs_read_node: cannot read node 1 from LEB 1619:475720, error -19

UBIFS error (pid 0): do_readpage: cannot read page 1004 of inode 68, error -19

Error reading file 'vmlinux.64'

vmlinux.64 not found!

argv[2]: quiet

argv[3]: cOnsole=ttyS0,9600

argv[4]: numcores=32

argv[5]: mtdparts=octeon_nand0:1024m(system)

Allocating memory for ELF segment: addr: 0xffffffff80100000 (adjusted to: 0x100000), size 0x2c750b0

## Loading big-endian Linux kernel with entry point: 0xffffffff807551a0 ...

Bootloader: Done loading app on coremask: 0xffffffff

Starting cores 0xffffffff