请问H3C MSR26-00 支持指定网段或者vlan走指定的wan口么

策略路由啊

可以的

直接使用pbr绑定acl，丢给指定出接口的下一跳即可

配置参考

https://www.h3c.com/cn/d_201401/812766_30005_0.htm

做策略路由就可以实现，具体参照1.3

https://www.h3c.com/cn/d_202312/1988687_30005_0.htm

您好，请知：

可以配置策略路由实现特定网段走特定出口。

以下是策略路由的配置案例，请参考：

3.1  组网需求

如图1所示，RouterA到达RouterC的路由下一跳为RouterB，在RouterB上通过策略路由、Track与NQA联动，对到达Router C的链路有效性进行实时判断。

图1 策略路由与NQA联动配置组网图

3.2  配置思路

·     为实现全网互通，配置路由协议；

·     为监控策略路由，建立NQA测试组；

·     为使能NQA，Track与NQA测试组关联。

3.3  使用版本

本举例是在Release 2317版本上进行配置和验证的。

3.4  配置注意事项

策略路由可以在配置报文的发送接口、缺省发送接口、下一跳、缺省下一跳时与Track项关联，通过Track项的状态来动态地决定策略的可用性。当应用动作增加Track关联后，如果事件发生时Track项状态为positive，则该配置项有效，可以指导转发；事件发生时，Track项状态为negative，则该配置项无效，转发时忽略该配置项。

3.5  配置步骤

3.5.1  RouterA的配置

# 配置以太网口的IP地址

<RouterA>system-view

[RouterA]interface GigabitEthernet 0/1 

[RouterA-GigabitEthernet0/1]ip address 200.1.1.1 255.255.255.0

[RouterA-GigabitEthernet0/1]quit

# 创建RIP动态路由

[RouterA]rip 1

[RouterA-rip-1]version 2

[RouterA-rip-1]network 200.1.1.0

3.5.2  RouterB的配置

# 定义访问控制列表

<RouterB>system-view

[RouterB]acl number 3009

[RouterB-acl-adv-3009]rule 0 permit ip source 200.1.1.0 0.0.0.255

[RouterB-acl-adv-3009]quit

# 创建虚接口VT87，并配置其IP地址

[RouterB]interface Virtual-Template 87

[RouterB-Virtual-Template87]ip address 1.1.1.1 255.255.255.0 

[RouterB-Virtual-Template87]quit

# 配置串口S8/7，使其MP捆绑到虚接口VT87上

[RouterB]interface Serial 8/7

[RouterB-Serial8/7]ppp mp Virtual-Template 87

[RouterB-Serial8/7]quit

# 定义1号节点，使匹配ACL 3009的任何IP报文被发往接口VT87，并配置与track1的联动配置

[RouterB]policy-based-route test permit node 1

[RouterB-pbr-test-1]if-match acl 3009

[RouterB-pbr-test-1]apply output-interface Virtual-Template87 track 1

[RouterB-pbr-test-1]quit

# 创建ICMP类型的NQA测试组（管理员为admin，操作标签为 1）并配置相关可选测试参数

[RouterB]nqa entry admin 1

[RouterB-nqa-admin-1]type icmp-echo

[RouterB-nqa-admin-1-icmp-echo]destination ip 1.1.1.2

[RouterB-nqa-admin-1-icmp-echo]frequency 5000

[RouterB-nqa-admin-1-icmp-echo]source ip 1.1.1.1

# 配置Reaction监测项1（失败1次触发联动）

[RouterB-nqa-admin-1-icmp-echo]reaction 1 checked-element probe-fail threshold-type consecutive 1 action-type trigger-only 

[RouterB-nqa-admin-1-icmp-echo]quit 

# 配置以太口GigabitEthernet0/1的IP地址，在GigabitEthernet0/1接口上应用策略路由test

[RouterB]interface GigabitEthernet 0/1

[RouterB-GigabitEthernet0/1]ip address 200.1.1.2 255.255.255.0

[RouterB-GigabitEthernet0/1]ip policy-based-route test

[RouterB-GigabitEthernet0/1]quit

# 配置Track项1，关联NQA测试组（管理员为admin，操作标签为 1）的Reaction监测项1

[RouterB]track 1 nqa entry admin 1 reaction 1

# 创建RIP动态路由

[RouterB]rip 1

[RouterB-rip-1]version 2

[RouterB-rip-1]network 200.1.1.0 

[RouterB-rip-1]network 1.1.1.0 

3.5.3  RouterC的配置

# 创建虚接口VT87，并配置其IP地址

<RouterC>system-view

[RouterC]interface Virtual-Template 87  

[RouterC-Virtual-Template87]ip address 1.1.1.2 255.255.255.0

[RouterC-Virtual-Template87]quit

# 配置串口S8/7，使其MP捆绑到虚接口VT87上

[RouterC]interface Serial 8/7 

[RouterC-Serial8/7]ppp mp Virtual-Template 87

[RouterC-Serial8/7]quit  

# 创建RIP动态路由

[RouterC]rip 1

[RouterC-rip-1]version 2

[RouterC-rip-1]network 1.1.1.0

3.6  验证结果

(1)     启动ICMP测试操作

[RouterB]nqa schedule admin 1 start-time now lifetime forever  

(2)     在RouterB显示ICMP  NQA测试成功的结果，NQA将探测结果通知给TRACK模块，则对应Track项的状态为positive，就表示策略路由指定的出接口有效，可以指导转发

 [RouterB]display nqa result admin 1

  NQA entry(admin admin, tag 1) test results:

    Destination IP address: 1.1.1.2

      Send operation times: 1              Receive response times: 1

      Min/Max/Average round trip time: 38/38/38

      Square-Sum of round trip time: 1444

      Last succeeded probe time: 2011-09-28 15:11:57.1

    Extend results:

      Packet lost in test: 0%

      Failures due to timeout: 0

      Failures due to disconnect: 0

      Failures due to no connection: 0

      Failures due to sequence error: 0

      Failures due to internal error: 0

      Failures due to other errors: 0      

[RouterB]display track 1

Track ID: 1

  Status: Positive

  Duration: 0 days 0 hours 4 minutes 50 seconds

  Notification delay: Positive 0, Negative 0 (in seconds)

  Reference object:

    NQA entry: admin 1

    Reaction: 1 

(3)     在RouterA发5个ping包到1.1.1.2，查看RouterB的策略路由的统计信息，统计成功转发了5个数据包

<RouterB>dispaly ip policy-based-route statistics interface GigabitEthernet 0/1

 Interface GigabitEthernet0/1 policy based routing statistics information:

 policy-based-route: test

    permit node 1

       apply output-interface Virtual-Template87 track 1

          Denied: 0,

          Forwarded: 5

 Total denied: 0, forwarded: 5 

(4)     断开RouterB与RouterC之间的连接线缆，在RouterB显示ICMP NQA测试不成功的结果，NQA将探测结果通知给TRACK模块，则对应Track项的状态为Negative，就表示策略路由指定的出接口无效，转发时忽略该配置项

 <RouterB>display nqa result admin 1

  NQA entry(admin admin, tag 1) test results:

    Destination IP address: 1.1.1.2

      Send operation times: 1              Receive response times: 0

      Min/Max/Average round trip time: 0/0/0

      Square-Sum of round trip time: 0

      Last succeeded probe time: 0-00-00 00:00:00.0

    Extend results:

      Packet lost in test: 100%

      Failures due to timeout: 1

      Failures due to disconnect: 0

      Failures due to no connection: 0

      Failures due to sequence error: 0

      Failures due to internal error: 0

      Failures due to other errors: 0

<RouterB>dis track 1

Track ID: 1

  Status: Negative

  Duration: 0 days 0 hours 4 minutes 50 seconds

  Notification delay: Positive 0, Negative 0 (in seconds)

  Reference object:

    NQA entry: admin 1

Reaction: 1  

(5)     在RouterA发5个ping包到1.1.1.2，查看RouterB的策略路由的统计信息，统计显示忽略了这5个数据包，这些数据包无法通过此策略路由进行转发，需按正常转发流程处理。

<RouterB>dispaly ip policy-based-route statistics interface GigabitEthernet 0/1

 Interface GigabitEthernet0/1 policy based routing statistics information:

 policy-based-route: test

    permit node 1

       apply output-interface Virtual-Template87 track 1

          Denied: 5,

          Forwarded: 0

 Total denied: 5, forwarded: 0