13:58:45:768 2013 H3C OPTMOD/4/MODULE_IN: GigabitEthernet1/0/25: The transceiver is 1000_BASE_LX_SFP.
[H3C]dis interface GigabitEthernet 1/0/25
GigabitEthernet1/0/25
Current state: DOWN
Line protocol state: DOWN
IP packet frame type: Ethernet II, hardware address: 00dd-b68d-aa11
Description: GigabitEthernet1/0/25 Interface
Bandwidth: 1000000 kbps
Loopback is not set
Media type is optical fiber, Port hardware type is 1000_BASE_LX_SFP
Unknown-speed mode, unknown-duplex mode
Link speed type is autonegotiation, link duplex type is autonegotiation
Flow-control is not enabled
Maximum frame length: 10000
Allow jumbo frames to pass
Broadcast max-ratio: 100%
Multicast max-ratio: 100%
Unicast max-ratio: 100%
PVID: 1
MDI type: Automdix
Port link-type: Access
Tagged VLANs: None
Untagged VLANs: 1
Port priority: 0
Last link flapping: Never
Last clearing of counters: Never
Current system time:2013-04-07 14:06:54
Last time when physical state changed to up:-
Last time when physical state changed to down:2013-01-01 00:00:46
Peak input rate: 0 bytes/sec, at 2013-01-01 00:02:00
Peak output rate: 0 bytes/sec, at 2013-01-01 00:02:00
Last 300 seconds input: 0 packets/sec 0 bytes/sec -%
Last 300 seconds output: 0 packets/sec 0 bytes/sec -%
Input (total): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
Input (normal): 0 packets, - bytes
0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
Input: 0 input errors, 0 runts, 0 giants, 0 throttles
0 CRC, 0 frame, - overruns, 0 aborts
- ignored, - parity errors
Output (total): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
Output (normal): 0 packets, - bytes
0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
Output: 0 output errors, - underruns, - buffer failures
0 aborts, 0 deferred, 0 collisions, 0 late collisions
0 lost carrier, - no carrier
(0)
检查下两端的功率情况
(0)
GigabitEthernet1/0/25 transceiver diagnostic information: Current diagnostic parameters: Temp.(▒▒C) Voltage(V) Bias(mA) RX power(dBm) TX power(dBm) 34 3.42 19.69 -40.00 -5.64 Alarm thresholds: Temp.(▒▒C) Voltage(V) Bias(mA) RX power(dBm) TX power(dBm) High 85 3.60 85.00 -2.00 -1.00 Low -10 3.00 1.00 -26.02 -11.00
两端用的是两种交换机,这个是H3C的 还有一个是思科的
没关系,功率正常,速率一致就可以
这不是模块的问题吧
太乱了,下面回答上图看下吧
是否光模块单模多模混用了?
(0)
这有可能是模块的问题吗?
没有,都是一个型号的,用的是烽火的
这有可能是模块的问题吗?
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明
太乱了,下面回答上图看下吧