<H3C>
<H3C>dis
<H3C>display loop
<H3C>display loopback-detection
Loopback detection is enabled.
Loopback detection interval is 250 second(s).
No loopback is detected.
<H3C>dis
<H3C>display stp
<H3C>display stp tc
-------------- STP slot 1 TC or TCN count -------------
MST ID Port Receive Send
0 Bridge-Aggregation1 0 76504
0 GigabitEthernet1/0/17 71 76376
0 GigabitEthernet1/0/18 2 76508
0 GigabitEthernet1/0/19 0 34460
0 GigabitEthernet1/0/21 0 76504
0 GigabitEthernet1/0/22 0 76504
0 GigabitEthernet1/0/24 0 76504
0 Ten-GigabitEthernet1/0/26 7566 62040
0 Ten-GigabitEthernet1/0/27 31608 7648
Ten-GigabitEthernet1/0/26
Current state: UP
Line protocol state: UP
IP packet frame type: Ethernet II, hardware address: 9023-b400-68a3
Description: Ten-GigabitEthernet1/0/26 Interface
Bandwidth: 1000000 kbps
Loopback is not set
Media type is optical fiber, Port hardware type is 1000_BASE_SX_SFP
1000Mbps-speed mode, full-duplex mode
Link speed type is force link, link duplex type is force link
Flow-control is not enabled
Maximum frame length: 10000
Allow jumbo frames to pass
Broadcast max-ratio: 100%
Multicast max-ratio: 100%
Unicast max-ratio: 100%
PVID: 3
MDI type: Automdix
Port link-type: Access
Tagged VLANs: None
Untagged VLANs: 3
Port priority: 0
Last link flapping: 33 weeks 1 days 17 hours 26 minutes
Last clearing of counters: Never
Peak input rate: 19160862 bytes/sec, at 2013-05-26 11:58:04
Peak output rate: 115320686 bytes/sec, at 2013-05-09 14:02:50
Last 300 second input: 379 packets/sec 258589 bytes/sec 0%
Last 300 second output: 304 packets/sec 126968 bytes/sec 0%
Input (total): 3022733592 packets, 1779402370679 bytes
3006295826 unicasts, 2670971 broadcasts, 13766795 multicasts, 0 pauses
Input (normal): 3022733592 packets, - bytes
3006295826 unicasts, 2670971 broadcasts, 13766795 multicasts, 0 pauses
Input: 0 input errors, 0 runts, 0 giants, 0 throttles
0 CRC, 0 frame, - overruns, 0 aborts
- ignored, - parity errors
Output (total): 3448373252 packets, 3176479285048 bytes
3436975208 unicasts, 582362 broadcasts, 10815682 multicasts, 0 pauses
Output (normal): 3448373252 packets, - bytes
3436975208 unicasts, 582362 broadcasts, 10815682 multicasts, 0 pauses
Output: 0 output errors, - underruns, - buffer failures
0 aborts, 0 deferred, 0 collisions, 0 late collisions
0 lost carrier, - no carrier
Ten-GigabitEthernet1/0/27
Current state: UP
Line protocol state: UP
IP packet frame type: Ethernet II, hardware address: 9023-b400-68a4
Description: Ten-GigabitEthernet1/0/27 Interface
Bandwidth: 1000000 kbps
Loopback is not set
Media type is optical fiber, Port hardware type is 1000_BASE_SX_SFP
1000Mbps-speed mode, full-duplex mode
Link speed type is force link, link duplex type is force link
Flow-control is not enabled
Maximum frame length: 10000
Allow jumbo frames to pass
Broadcast max-ratio: 100%
Multicast max-ratio: 100%
Unicast max-ratio: 100%
PVID: 4
MDI type: Automdix
Port link-type: Access
Tagged VLANs: None
Untagged VLANs: 4
Port priority: 0
Last link flapping: 33 weeks 1 days 17 hours 26 minutes
Last clearing of counters: Never
Peak input rate: 20494184 bytes/sec, at 2013-01-19 16:17:56
Peak output rate: 86769413 bytes/sec, at 2013-06-13 15:32:52
Last 300 second input: 559 packets/sec 132548 bytes/sec 0%
Last 300 second output: 1434 packets/sec 1857470 bytes/sec 1%
Input (total): 6716213457 packets, 4659461641905 bytes
6679833168 unicasts, 6477285 broadcasts, 29903004 multicasts, 0 pauses
Input (normal): 6716213457 packets, - bytes
6679833168 unicasts, 6477285 broadcasts, 29903004 multicasts, 0 pauses
Input: 0 input errors, 0 runts, 0 giants, 0 throttles
0 CRC, 0 frame, - overruns, 0 aborts
- ignored, - parity errors
Output (total): 7910127021 packets, 6937415746059 bytes
7895987332 unicasts, 13343955 broadcasts, 795734 multicasts, 0 pauses
Output (normal): 7910127021 packets, - bytes
7895987332 unicasts, 13343955 broadcasts, 795734 multicasts, 0 pauses
Output: 0 output errors, - underruns, - buffer failures
0 aborts, 0 deferred, 0 collisions, 0 late collisions
0 lost carrier, - no carrier
(0)
光口27口收到的TC报文比较多,沿着这个口往下查一下。
先看一下接口的收发光,在去对端设备查看一下,
看对端设备是哪个口收到的tc报文比较多,沿路往下查
顺便把接终端的设备配置成边缘端口
(0)
暂无评论
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明
暂无评论