华三S5120V3交换机对接华为5135s交换机光口不亮问题

S5120V3交换机华三光口配置：

port link-type trunk

 port trunk permit vlan all

 speed 1000

 duplex full

光口下信息

[FD3]display interface Ten-GigabitEthernet 1/0/25

Ten-GigabitEthernet1/0/25

Current state: UP

Line protocol state: UP

IP packet frame type: Ethernet II, hardware address: b845-f4ff-798b

Description: Ten-GigabitEthernet1/0/25 Interface

Bandwidth: 1000000 kbps

Loopback is not set

Media type is optical fiber, Port hardware type is 1000_BASE_LX_SFP

1000Mbps-speed mode, full-duplex mode

Link speed type is force link, link duplex type is force link

Flow-control is not enabled

Maximum frame length: 12288

Allow jumbo frames to pass

Broadcast max-ratio: 100%

Multicast max-ratio: 100%

Unicast max-ratio: 100%

Known-unicast max-ratio: 100%

[H3C]display transceiver diagnosis interface Ten-GigabitEthernet 1/0/25

Ten-GigabitEthernet1/0/25 transceiver diagnostic information:

  Current diagnostic parameters:

    Temp.(°C) Voltage(V)  Bias(mA)  RX power(dBm)  TX power(dBm)

    36         3.38        13.23     -6.44          -6.13

  Alarm thresholds:

          Temp.(°C) Voltage(V)  Bias(mA)  RX power(dBm)  TX power(dBm)

    High  73         3.60        48.43     -3.00          6.00

    Low   -3         3.00        1.00      -22.01         -12.50

华为交换机光口配置信息

[huawei]display transceiver diagnosis interface GigabitEthernet 0/0/25

Port GigabitEthernet0/0/25 transceiver diagnostic information:

Parameter        Current       Low Alarm    High Alarm

  Type            Value        Threshold    Threshold    Status

-------------   ---------      ---------    ----------   --------

TxPower(dBm)    -6.05          -12.50       6.00         normal

RxPower(dBm)    -40.00         -22.01       -3.00        abnormal

Current(mA)     13.45          1.00         48.85        normal

Temp.(°C)      38.91          -3.00        73.00        normal

Voltage(V)      3.30           3.00         3.60         normal

[fuliaokuAP-POESW2-GigabitEthernet0/0/25]di this 

#

interface GigabitEthernet0/0/25

 undo negotiation auto

 port link-type trunk

 port trunk allow-pass vlan 2 to 4094

#

华为交换机报错信息：

ul  5 2021 19:34:36 fuliaokuAP-POESW2 %%01RM/4/ROUTERID_CHANGE(l)[0]:The router ID is . (InstanceID=0)

Jul  5 2021 19:33:59 fuliaokuAP-POESW2 %%01RM/4/ROUTERID_CHANGE(l)[1]:The router ID is 0.0.0.0. (InstanceID=0)

Jul  5 2021 02:52:18 fuliaokuAP-POESW2 %%01CFM/4/BACKUPCONFIG_SUC(s)[2]:Succeeded in backing up file flash:/$_backup/running_config/20210705025217.fuliaokuAP-POESW2.zip.

Jul  5 2021 02:23:58 fuliaokuAP-POESW2 %%01IFADP/4/PORTDOWNINFO(l)[3]:Interface GigabitEthernet0/0/25 has turned into DOWN state. (Information=Physical state: down, Negotiation: disable, Negotiation complete: no, Local speed(100M: no, 1000M: yes), RX loss of signal: yes, Current RX power(dBM): -40.00, Current TX power(dBM): -5.82)

Jul  5 2021 02:23:58 fuliaokuAP-POESW2 %%01IFNET/4/LINK_STATE(l)[4]:The line protocol IP on the interface Vlanif1 has entered the DOWN state.

Jul  5 2021 02:23:58 fuliaokuAP-POESW2 %%01IFNET/4/IF_STATE(l)[5]:Interface Vlanif1 has turned into DOWN state.

 一台华三S5120V3交换机对接华为交换机。两台设备都是千兆口，都是用千兆的模块。已经尝试过两端都用华三的模块和两端都用华为的模块，一端用华为一端用华三。。。。都是华三这台交换机的光口亮。

麻烦各位大佬帮看看！！！！