H3C SecPath ACG1000-ME Console 连接后键盘无法输入 网口无法连接

症状：

SecureCRT终端通过Console连接设备，通电可引导启动，停留在输入用户名却无法进行输入，光标闪烁正常；

机器前面板工作灯正常；

用网线连接千兆网口-0或1口，电脑网卡显示”未连接“；

贴上设备启动信息【Console口连接】

--------------------------------分割线--------------------------------

SPI stage 1 bootloader

SPI ID: ef:40:17:00:00

header found at offset 0x10000

Image 1.2: address: 0xffffffffc0000000, header length: 192, data length: 458032

Validating data...

Starting stage 1.5 bootloader at 0xffffffff81000000

Warning: Board descriptor tuple not found in eeprom, using defaults

OCTEON CN7130-AAP pass 1.2, Core clock: 1200 MHz, IO clock: 400 MHz, DDR clock: 667 MHz (1334 Mhz DDR)

Base DRAM address used by u-boot: 0x8fc00000, size: 0x400000

DRAM: 2 GiB

Clearing DRAM...... done

Using default environment

MMC:   Octeon MMC/SD0: 1

SF: Detected W25Q64CV with page size 256 Bytes, erase size 4 KiB, total 8 MiB

Found valid SPI bootloader at offset: 0x100000, size: 1516120 bytes

U-Boot 1.6.32 (Build time: Jun 27 2019 - 15:04:09)

Using DRAM size from environment: 2048 MBytes

OCTEON CN7130-AAP pass 1.2, Core clock: 1200 MHz, IO clock: 400 MHz, DDR clock: 667 MHz (1334 Mhz DDR)

Base DRAM address used by u-boot: 0x8e000000, size: 0x2000000

DRAM: 2 GiB

Clearing DRAM...... done

xspeed NEW CUST_NC01 board detected

sata detected

Octeon MMC/SD0: 1

Flash boot bus region not enabled, skipping NOR flash config

PCIe: Port 0 link active, 1 lanes, speed gen1

PCIe: Port 1 stuck in reset, skipping.

PCIe: Port 2 not in PCIe mode, skipping

PCI console init succeeded, 1 consoles, 1024 bytes each

Press CTRL+C to enter menuboot: 0

reading vmlinux.64

...........................................

44082896 bytes read in 7735 ms (5.4 MiB/s)

argv[2]: cOnsole=ttyS0,9600

argv[3]: numcores=4

Allocating memory for ELF segment: addr: 0xffffffff80100000 (adjusted to: 0x100000), size 0x2c750b0

## Loading big-endian Linux kernel with entry point: 0xffffffff807551a0 ...

Bootloader: Done loading app on coremask: 0xf

Starting cores:

 0xf

/sbin/rc starting

Mounting file systems

Setting up loopback

log disk part is sda1.

mgt0 MAC address is : 5c:c9:99:ca:88:fd

CVMX_SHARED: 0x10d00000-0x11390000

Active coremask = 0xf

Node 0 Interface 0 has 1 ports (RXAUI)

Node 0 Interface 2 has 4 ports (NPI)

Node 0 Interface 3 has 4 ports (LOOP)

Node 0 Interface 4 has 1 ports (AGL)

BOOTMEM 0x4b000000 size 1104MB(1157627904B)

Page size 16384 bytes, memory regions:

 0: 0x800000004b33c000 -> 0x8000000090000000 (1154236416 bytes)

Buddy initialized

Slub initialized

nf_conntrack (size 504 buckets 131072 max 2000000) memory:2GB

Application identify initialized

Application audit initialized

Intrusion Prevention System initialized

Anti-Virus Protection initialized

WAF initialized

TCP Stack initialized

The configuration is loaded !

watchdog init ok.

watchdog pthread init ok.

/sbin/rc complete

Username: 

--------------------------------分割线--------------------------------