H3C Comware Platform Software
Comware Software, Version 5.20.99, Release 1112
Copyright (c) 2004-2019 New H3C Technologies Co., Ltd. All rights reserved.
H3C S5048PV2-EI uptime is 0 week, 0 day, 0 hour, 57 minutes
版本升级到最新
H3C S5048PV2-EI
128M bytes DRAM
32M bytes Flash Memory
Config Register points to Flash
Hardware Version is Ver.A
Bootrom Version is 121
[SubSlot 0] 48GE+4SFP Hardware Version is Ver.A
41-48电口不来,查看端口状态
GigabitEthernet1/0/41 current state: DOWN
IP Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: 741f-4ab4-f35e
Description: GigabitEthernet1/0/41 Interface
Loopback is not set
Media type is optical fiber, Port hardware type is No connector
100Mbps-speed mode, unknown-duplex mode
Link speed type is force link, link duplex type is autonegotiation
Flow-control is not enabled
The Maximum Frame Length is 9600
Broadcast MAX-ratio: 100%
Unicast MAX-ratio: 100%
Multicast MAX-ratio: 100%
PVID: 1
Mdi type: auto
Port link-type: access
Tagged VLAN ID : none
Untagged VLAN ID : 1
Port priority: 0
Last clearing of counters: Never
Peak value of input: 0 bytes/sec, at 00-00-00 00:00:00
Peak value of output: 0 bytes/sec, at 00-00-00 00:00:00
Last 300 seconds input: 0 packets/sec 0 bytes/sec 0%
Last 300 seconds output: 0 packets/sec 0 bytes/sec 0%
Input (total): 0 packets, 0 bytes
复用口,切换一下模式:
比如当前使用G1/0/1为光口,那么标号G1/0/1的电口就无法使用;
可以在接口下通过combo enable 【copper 或 fiber】copper代表电口,fiber代表光口
Combo端口是一个逻辑端口,一个Combo端口对应设备面板上的一个电口和一个光口。电口与其对应的光口均为设备上的以太网端口,是光电复用关系,两者不能同时工作(当激活其中的一个端口时,另一个端口就自动处于禁用状态),用户可根据组网需求选择使用电口或光口。
电口和光口有各自对应的端口视图。当用户需要激活电口或光口、配置电口或光口的属性(比如速率、双工等)时,必须先进入对应的端口视图。
· 通过display port combo命令了解设备上有哪些Combo端口,每个Combo端口是由哪两个物理端口组成的。
· 通过display interface命令了解当前处于激活状态的是电口还是光口。如果显示信息中包含“Media type is twisted pair, Port hardware type is 1000_BASE_T”,则表示电口处于激活状态,否则,则表示光口
接口显示Media type is optical fiber, 41-48全是电口
亲~登录后才可以操作哦!
确定你的邮箱还未认证,请认证邮箱或绑定手机后进行当前操作
举报
×
侵犯我的权益
×
侵犯了我企业的权益
×
抄袭了我的内容
×
原文链接或出处
诽谤我
×
对根叔社区有害的内容
×
不规范转载
×
举报说明
接口显示Media type is optical fiber, 41-48全是电口